Table of Contents
Advertisement
Available languages
Available languages
17) PTT
Transmission key, press to
transmit
to
listen to
an incoming communication,
TOT (Time Out Timer)
If the PTT switch (17) key is pressed for more than 5 minutes, the display starts
blinking and the transmission ends. A beep will sound until the PTT switch
(17) key is released.
18) UP/DN BUTTONS ON MICROPHONE
In normal use, press UP/DN buttons (18) on the microphone to
channel. UP to
increase
and DN to
See ROTARY "PUSH" KNOB page 7.
A) DC-POWER TERMINAL (13,8 V)
B) ANTENNA CONNECTOR (SO-239)
C) JACK FOR EXTERNAL OPTIONAL SPEAKER (8 Ω, Ø 3.5 mm)
D) JACK FOR PA OPTIONAL SPEAKER (Public Address) (8 Ω,
Ø 3.5 mm)
E) JACK FOR OPTIONAL VOX MICROPHONE (Ø 2.5 mm)
C) MENU
The order of 13 functions is as described in this manual. However, the func-
tion displayed by entering the MENU will be the last function modified by
user.
The procedure is the same whatever the function is:
Push the rotary PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
select
to
the menu.
2.
Push the rotary PUSH knob (6) to
function blinks on the display.
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
modify
the value of the parameter.
4.
New Push the rotary PUSH knob (6) to
rameter stops blinking and if the function has more than one parameter,
the next parameter blinks.
5.
If no key is pressed, the unit exits MENU after 10 seconds.
the display.
Note: UP/DN buttons (18) on the microphone have the same effect as the
a message,
is displayed and release
disappears.
change
decrease
the channel.
enter
MENU.
is displayed.
validate.
The parameter of the chosen
validate
the chosen value. The pa-
disappears from
rotation of the rotary PUSH knob (6). PTT switch (17)
exists
MENU.
and
disappears.
1) COLOR
This function allows to
Push the rotary PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the COLOR menu.
2.
Push the rotary PUSH knob (6) to
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (11) on the microphone
select
to
the color. 7 available colors are displayed over and over :
the
4.
New Push the rotary PUSH knob (6) to
stops blinking. a) Go back to point 1 to
the PTT switch (17) to
validate
5.
If no key is pressed, the unit
the display.
Default COLOR is
(Orange).
2) DIMMER
The DIMMER function allows to
backlight or to set no backlight (OF).
Push the rotary PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the DIMMER menu.
2.
Push the rotary PUSH knob (6) to
on the display.
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
select
to
a new value.
4.
New Push the rotary PUSH knob (6) to validate. The parameter stops blinking.
a) Go back to point 1 to
validate
exit
(17) to
and
5.
If no key is pressed, the unit
the display.
Default DIMMER value is 9.
3) KEY BEEP
When the function is activated, a beep
changing the channel etc. "BP" appears on the display when the function
is active.
10
validates
choose
the backlight color of the LCD.
enter
MENU.
validate.
The current color blinks on LCD.
validate
the chosen color. The color
adjust
another function or b) Press
exit
MENU.
and
disappears in the display.
exits
MENU after 10 seconds,
adjust
the brightness (from 1 to 9) of the
enter
MENU.
validate.
The value of the dimmer blinks
adjust
another function or b) Press the PTT switch
MENU.
disappears.
exits
MENU after 10 seconds,
sounds
when a key is pressed, by
the last setting
is displayed.
disappears in
is displayed.
disappears in
Advertisement
Table of Contents
