Korg KROSS Operation Manual page 19

ENTER button and ▲▼ cursor buttons
When you select a parameter and press the ENTER button, a
▲▼ symbol will appear beside the value (
you can use the ▲▼ cursor buttons to increment or decrement
the value in steps of one. When you've specified the value, press
the ENTER button once again to confirm it. This method is
convenient when you want to make small changes.
Note: If you decide not to change the value, press the EXIT button.
Using the keyboard to enter a note number or velocity
value
For parameters that specify a note number (such as G4 or C#2) or
a velocity value, pressing the ENTER button will cause a ▲▼
symbol to appear beside the value (see above). You can play a
key to directly enter a note number or velocity value. When
you've specified the value, press the ENTER button once again to
confirm it.
ENTER button
If the parameter item is a toggle, radio button, or check box, press
the ENTER button to switch the setting.
Other
CATEGORY dial, VALUE dial
Parameters indicated by (category select icon) can be edited
using the CATEGORY dial and VALUE dial to change the
category and program/combination number. The dial's LED will
light to indicate the current category.
In Program mode you can select the program category and
number.
In Combination mode these dials have the following two
functions.
• Select the combination category and number.
• When the edit cell is a timbre program (highlighted), the
dials select the program category and number.
In Sequencer mode when the edit cell is a track program
(highlighted), the dials select the program category and number.
Compare/Undo function
Program, Combination mode
Use this when you wish to compare the edits you have made to a
program or combination's sound with the un-edited original (i.e.,
the sound that is written into memory).
While editing a program or combination, you can turn on the
Compare function (select the check mark) to recall the settings
that were last written to that program number or combination
number. When you turn off the Compare function (remove the
check mark), you will return to the settings that you had
previously been editing.
1. While editing, turn the Compare function on (select
the check mark).
To turn this on, press the FUNCTION button to access
the function list, use the PAGE+ (▼) or PAGE– (▲)
button to select Compare, and press the MENU (OK)
button.
The sound that had been saved before you began editing
will be recalled.
2. When you turn off the Compare function (remove the
check mark), you will return to the sound that you
had previously been editing.
To turn it off, select the Compare function once again and
press the MENU (OK) button.
Note: If you edit the settings that were recalled by turning
Compare on (i.e., the saved settings), the check mark will be
cleared, and your previously edited settings will be lost. Even if
you turn Compare on again (select the check mark), the previous
→ ), and
settings will not return.
Sequencer mode
In Sequencer mode, you can use the Undo function to make
"before and after" comparisons immediately after using realtime
recording or step recording to record a song, or after performing
an edit on a track.
For example, this can be used effectively when realtime-
recording a MIDI track for a song.
1. Realtime-record a MIDI track. (Take 1)
2. Once again, realtime-record on the same track.
(Take 2)
3. If you turn on the Undo function (select the check
mark), take 1 will be recalled.
4. If you turn off the Undo function (clear the check
mark), take 2 will be recalled.
5. If at step 3 you once again realtime-record on the
same track (take 3), the Compare function will now be
referencing take 1.
6. If at step 4 you once again realtime-record on the
same track (take 3), the Compare function will be
referencing take 2.
In this way, the Undo function lets you recall the previous
recording or the previous state of event editing.
Note: If you edit while Undo is on (the check mark selected), the
check mark will be cleared. That musical data now becomes the
musical data that will be selected when Undo is off.
Global/Media mode
The Compare function is not available in Global/Media mode.
Audio recorder
When using the audio recorder, you can use Undo to return to a
previously recorded state. You can step back through multiple
takes. You can also redo. In the AUDIO RECORDER SETUP
dialog box, press the PAGE– (UNDO) button.
Pad Audio Play
As with the audio recorder, the pad audio play function also lets
you return to the previously recorded state. In the AUDIO SONG
SETUP dialog box, press the PAGE- (UNDO) button.
Pad Sampler
The compare function cannot be used with pad sampler
recording, nor when editing in the EDIT SAMPLE window.
Basic Information Basic operations
13