Table of Contents
Advertisement
•
Short Edge: Prints pages to be read by flipping like a note pad.
2
3
5
7. Press OK to save your selection.
8. Press Stop/Clear to return to ready mode.
Receiving faxes in memory
Since your machine is a multi-tasking device, it can receive faxes while you
are making copies or printing. If you receive a fax while you are copying or
printing, your machine stores incoming faxes in its memory. Then, as soon
as you finish copying or printing, the machine automatically prints the fax.
ADJUSTING THE DOCUMENT SETTINGS
Before starting a fax, change the following settings according to your
original's status to get the best quality.
Resolution
The default document settings procedure good results when using typical
text-based originals. However, if you send originals that are of poor quality,
or contain photographs, you can adjust the resolution to produce a higher
quality fax.
1. Press Fax on the control panel.
2. Press Menu on the control panel.
3. Press the up/down arrow to highlight Fax Feature and press OK.
4. Press the up/down arrow to highlight Resolution and press OK.
5. Press the up/down arrow until the option you want highlights and press
OK.
6. Press Stop/Clear to return to ready mode.
Recommended resolution settings for different original document types are
described in the table below:
MODE
Standard
Originals with normal sized characters.
Fine
Originals containing small characters or thin lines or
originals printed using a dot-matrix printer.
RECOMMENDED FOR:
MODE
Super Fine
Originals containing extremely fine detail. Super Fine
mode is enabled only if the machine with which you
are communicating also supports the Super Fine
resolution.
Photo Fax
Originals containing shades of gray or photographs.
Color Fax
Originals with colors. Sending a color fax is enabled
only if the machine with which you are
communicating supports color fax reception and you
send the fax manually. In this mode, memory
transmission is not available.
The resolution setting is applied to the current fax job. To change the
default setting, see "Change Default" on page 93.
Darkness
You can select the degree of darkness of the original document.
1. Press Fax on the control panel.
2. Press Menu on the control panel.
3. Press the up/down arrow to highlight Fax Feature and press OK.
4. Press the up/down arrow to highlight Darkness and press OK.
5. Press the up/down arrow until the option you want highlights and press
OK.
6. Press Stop/Clear to return to ready mode.
The darkness setting is applied to the current fax job. To change the
default setting, see "Change Default" on page 93.
FORWARDING A FAX TO OTHER DESTINATION
You can set the machine to forward the received or sent fax to other
destination by a fax, an email or a server. If you are out of office but have to
receive the fax, this feature may be useful.
When you forward a fax by an email, you firstly set the mail server and
IP address in SyncThru™ Web Service. (See "Using SyncThru™ Web
Service" on page 99.)
Forwarding a sent fax to other destination by a fax
You can set the machine to forward every fax you sent to other destination
by faxing.
1. Press Fax on the control panel.
2. Press Menu on the control panel.
3. Press the up/down arrow to highlight Fax Feature and press OK.
4. Press the up/down arrow to highlight Forward and press OK.
5. Press the up/down arrow to highlight Fax and press OK.
6. Press the up/down arrow to highlight Send Forward and press OK.
7. Press the up/down arrow to highlight On and press OK.
Faxing_ 85
RECOMMENDED FOR:
•
For memory transmission, Super Fine
mode is not available. The resolution setting
is automatically changed to Fine
•
When your machine is set to Super Fine
resolution and the fax machine with which
you are communicating does not support
Super Fine resolution, the machine
transmits using the highest resolution mode
supported by the other fax machine.
Advertisement
Table of Contents
