Step Phaser - Roland RD-2000 Parameter Manual

Parameter Value
Drive # 0–127
Vowel1
A, E, I, O, U
Vowel2 A, E, I, O, U
Rate
OFF, ON
(sync sw)
Rate (Hz) # / 0.05–10.00
Rate (note) # note (p. 60)
Depth # 0–127
Input Sync
OFF, ON
Sw
Input Sync
0–127
Threshold
Manual # 0–100
Low Gain
-15–+15
High Gain -15–+15
Pan # L64–63R
Level
0–127
18: PHASER 1
A phase-shifted sound is added to the original sound and
modulated.
L in
Phaser
Phaser
R in
Parameter Value
Switch OFF, ON
Depth Knob
MANUAL,
RATE,
RESONANCE,
MIX
Rate Knob
OFF,
MANUAL,
Feedback
RATE,
Knob
RESONANCE,
MIX
Explanation
Degree of distortion
Also changes the volume.
Selects the vowel.
If this is ON, the modulation
is synchronized to the tempo
of the rhythm (owner's
manual: p. 24).
[Hz]
Frequency at which the two
vowels switch
Effect depth
LFO reset on/off
Determines whether the LFO
for switching the vowels is
reset by the input signal (ON)
or not (OFF).
Volume level at which reset
is applied
Point at which Vowel 1/2
switch
49 or less: Vowel 1 will have
a longer duration.
50:
Vowel 1 and 2 will be of
equal duration.
51 or more:
Vowel 2 will
have a longer duration.
Gain of the low frequency
[dB]
range
Gain of the high frequency
[dB]
range
Stereo location of the output
Output level
2-Band
L out
EQ
Mix
Mix
2-Band
R out
EQ
Explanation
Turns the effect on/off.
Specifies the parameter
that is controlled by the
MODULATION FX [DEPTH]
knob.
Specifies the parameter
that is controlled by the
MODULATION FX [RATE]
knob.
Specifies the parameter
that is controlled by the
MODULATION FX [FEEDBACK]
knob.
Parameter Value
4-STAGE,
Mode
8-STAGE,
12-STAGE
Manual # 0–127
Rate
OFF, ON
(sync sw)
Rate (Hz) #/ 0.05–10.00
Rate (note) # note (p. 60)
Depth 0–127
INVERSE,
Polarity
SYNCHRO
Resonance # 0–127
Cross
-98–+98
Feedback
Mix # 0–127
Low Gain -15–+15
High Gain -15–+15
Level 0–127

19: STEP PHASER

This is a stereo phaser. The phaser effect will be varied gradually.
L in
Step Phaser
Step Phaser
R in
Parameter Value
Switch
OFF, ON
Depth Knob
MANUAL,
RATE,
RESONANCE,
STEP RATE,
MIX
Rate Knob
Modulation FX Parameters
Explanation
Number of stages in the
phaser
Adjusts the basic frequency
from which the sound will be
modulated.
If this is ON, the modulation
is synchronized to the tempo
of the rhythm (owner's
manual: p. 24).
[Hz]
Frequency of modulation
Depth of modulation
Selects whether the left
and right phase of the
modulation will be the same
or the opposite.
INVERSE:
The left and right
phase will be opposite. When
using a mono source, this
spreads the sound.
SYNCHRO:
The left and
right phase will be the same.
Select this when inputting a
stereo source.
Amount of feedback
Adjusts the proportion of the
phaser sound that is fed back
[%]
into the effect. Negative
settings will invert the phase.
Level of the phase-shifted
sound
[dB] Gain of the low range
[dB] Gain of the high range
Output Level
2-Band
EQ
Mix
Mix
2-Band
EQ
Explanation
Turns the effect on/off.
Specifies the parameter
that is controlled by the
MODULATION FX [DEPTH]
knob.
Specifies the parameter
that is controlled by the
MODULATION FX [RATE]
knob.
"-"
L out
R out
41