Flanger; Step Flanger - Roland RD-2000 Parameter Manual

Parameter Value
OFF,
Filter Type LPF,
HPF
Cutoff Freq 200–8000
Pre Delay 0.0–100 [msec]
Rate
OFF, ON
(sync sw)
Rate (Hz) #/ 0.05–10.00
Rate (note) # note (p. 60)
Depth
0–127
Phase 0–180 [deg]
Low Gain -15–+15 [dB]
High Gain -15–+15 [dB]
D100:0W–
Balance #
D0:100W
Level 0–127

27: FLANGER

This is a stereo flanger. (The LFO has the same phase for left and
right.) It produces a metallic resonance that rises and falls like a jet
airplane taking off or landing. A filter is provided so that you can
adjust the timbre of the flanged sound.
Balance D
L in
Flanger
Feedback
Feedback
Flanger
R in
Balance D
Parameter Value
Switch OFF, ON
Depth Knob
RATE,
FEEDBACK,
BALANCE
Rate Knob
OFF,
Feedback RATE,
Knob FEEDBACK,
BALANCE
OFF,
Filter Type LPF,
HPF
Explanation
Type of filter
OFF:
no filter is used
LPF:
cuts the frequency
range above the Cutoff Freq
HPF: cuts the frequency
range below the Cutoff Freq
[Hz] Basic frequency of the filter
Adjusts the delay time from
the direct sound until the
chorus sound is heard.
If this is ON, the modulation
is synchronized to the tempo
of the rhythm (owner's
manual: p. 24).
[Hz]
Frequency of modulation
Depth of modulation
Spatial spread of the sound
Gain of the low range
Gain of the high range
Volume balance between
the direct sound (D) and the
chorus sound (W)
Output Level
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Explanation
Turns the effect on/off.
Specifies the parameter
that is controlled by the
MODULATION FX [DEPTH]
knob.
Specifies the parameter
that is controlled by the
MODULATION FX [RATE]
knob.
Specifies the parameter
that is controlled by the
MODULATION FX [FEEDBACK]
knob.
Type of filter
OFF:
no filter is used
LPF: cuts the frequency
range above the Cutoff Freq
HPF:
cuts the frequency
range below the Cutoff Freq
Parameter Value
Cutoff Freq
200–8000
Pre Delay
0.0–100 [msec]
Rate
OFF, ON
(sync sw)
Rate (Hz) #/ 0.05–10.00
Rate (note) # note (p. 60)
Depth 0–127
Phase
0–180 [deg]
Feedback # -98–+98 [%]
Low Gain -15–+15 [dB]
High Gain -15–+15 [dB]
D100:0W–
Balance #
D0:100W
Level 0–127

28: STEP FLANGER

This is a flanger in which the flanger pitch changes in steps. The
speed at which the pitch changes can also be specified in terms of
a note-value of a specified tempo.
Balance D
L in
Step Flanger
Feedback
Feedback
Step Flanger
R in
Balance D
Parameter Value
Switch
OFF, ON
Depth Knob
RATE,
FEEDBACK,
STEP RATE,
BALANCE
Rate Knob
OFF,
RATE,
Feedback
FEEDBACK,
Knob
STEP RATE,
BALANCE
OFF,
Filter Type LPF,
HPF
Cutoff Freq 200–8000
Modulation FX Parameters
Explanation
[Hz] Basic frequency of the filter
Adjusts the delay time from
the direct sound until the
flanger sound is heard.
If this is ON, the modulation
is synchronized to the tempo
of the rhythm (owner's
manual: p. 24).
[Hz]
Frequency of modulation
Depth of modulation
Spatial spread of the sound
Adjusts the proportion of the
flanger sound that is fed back
into the effect. Negative
settings will invert the phase.
Gain of the low range
Gain of the high range
Volume balance between
the direct sound (D) and the
flanger sound (W)
Output Level
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Explanation
Turns the effect on/off.
Specifies the parameter
that is controlled by the
MODULATION FX [DEPTH]
knob.
Specifies the parameter
that is controlled by the
MODULATION FX [RATE]
knob.
Specifies the parameter
that is controlled by the
MODULATION FX [FEEDBACK]
knob.
Type of filter
OFF:
no filter is used
LPF:
cuts the frequency
range above the Cutoff Freq
HPF: cuts the frequency
range below the Cutoff Freq
[Hz] Basic frequency of the filter
"-"
45