HP 10500 Series Configuration Manual page 80

[SwitchB-ospf-1] area 0
[SwitchB-ospf-1-area-0.0.0.0] network 2.2.2.9 0.0.0.0
[SwitchB-ospf-1-area-0.0.0.0] network 10.1.1.0 0.0.0.255
[SwitchB-ospf-1-area-0.0.0.0] network 20.1.1.0 0.0.0.255
[SwitchB-ospf-1-area-0.0.0.0] quit
[SwitchB-ospf-1] quit
# Configure Switch C.
<SwitchC> system-view
[SwitchC] ospf
[SwitchC-ospf-1] area 0
[SwitchC-ospf-1-area-0.0.0.0] network 3.3.3.9 0.0.0.0
[SwitchC-ospf-1-area-0.0.0.0] network 20.1.1.0 0.0.0.255
[SwitchC-ospf-1-area-0.0.0.0] network 21.1.1.0 0.0.0.255
[SwitchC-ospf-1-area-0.0.0.0] quit
[SwitchC-ospf-1] quit
# Verify that the switches have learned the routes to each other. For example, on Switch A:
[SwitchA] display ip routing-table
Destinations : 21
Destination/Mask
0.0.0.0/32
1.1.1.9/32
2.2.2.9/32
3.3.3.9/32
10.1.1.0/24
10.1.1.0/32
10.1.1.1/32
10.1.1.255/32
11.1.1.0/24
11.1.1.0/32
11.1.1.1/32
11.1.1.255/32
20.1.1.0/24
21.1.1.0/24
127.0.0.0/8
127.0.0.0/32
127.0.0.1/32
127.255.255.255/32
224.0.0.0/4
224.0.0.0/24
255.255.255.255/32
Enable MPLS and LDP:
3.
# Configure Switch A.
[SwitchA] mpls lsr-id 1.1.1.9
[SwitchA] mpls ldp
[SwitchA-ldp] quit
[SwitchA] interface vlan-interface 2
Routes : 21
Proto Pre Cost
Direct 0 0
Direct 0 0
OSPF 10 1
OSPF 10 2
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
OSPF 10 2
OSPF 10 3
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
74
NextHop Interface
127.0.0.1 InLoop0
127.0.0.1 InLoop0
10.1.1.2 Vlan2
10.1.1.2 Vlan2
10.1.1.1 Vlan2
10.1.1.1 Vlan2
127.0.0.1 InLoop0
10.1.1.1 Vlan2
11.1.1.1 Vlan4
11.1.1.1 Vlan4
127.0.0.1 InLoop0
11.1.1.1 Vlan4
10.1.1.2 Vlan2
10.1.1.2 Vlan2
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
0.0.0.0 NULL0
0.0.0.0 NULL0
127.0.0.1 InLoop0