Siemens SITRANS LUT400 Operating Instructions Manual page 289

2. SETUP - DATE AND TIME (cont' d )
2.14.3 DAYLIGHT SAVING
2. 1 4.3.1 ENABLE
2. 1 4.3.2 STARTING ORDINAL
2. 1 4.3.3 STARTING DAY
2. 1 4.3.4 STARTING MONTH
2. 1 4.3.5 ENDING ORDINAL
2. 1 4.3.6 ENDING DAY
2. 1 4.3.7 ENDING MONTH
2.15 FLOW (LUT430, 440 only)
2.15.1 PRIMARY MEASURING DEVICE
2.15.2 AUTO ZERO HEAD
2 15.3 BASIC SETUP
2. 1 5.3. 1 METHOD OF FLOW CALCULATION
2. 1 5.3.2 FLOW EXPONENT
2. 1 5.3.3 MAXIMUM HEAD
2. 1 5.3.4 MAXIMUM FLOW AT 20MA
2. 1 5.3.5 ZERO HEAD OFFSET
2. 1 5.3.6 FLOWRATE DECIMAL
2. 1 5.3.7 FLOWRATE UNITS
2. 1 5.3.8 USER DEFINED UNIT
2. 1 5.3.9 LOW FLOW CUTOFF
2 15.4 PMD DIMENSIONS
2. 1 5.4. 1 K FACTOR
2. 1 5.4.2 V NOTCH ANGLE
2. 1 5.4.3 SLOPE
2. 1 5.4.4 ROUGHNESS COEFFICIENT
2. 1 5.4.5 OCM DIMENSION 1
2. 1 5.4.6 OCM DIMENSION 2
2. 1 5.4.7 OCM DIMENSION 3
2. 1 5.4.8 OCM DIMENSION 4
2 15.5 UNIVERSAL HEAD VS FLOW
2. 1 5.5. 1 TABLE 1-8
2. 1 5.5.2 TABLE 9-16
2. 1 5.5.3 TABLE 17-24
2. 1 5.5.4 TABLE 25-32
2.16 TOTALIZERS (LUT430, 440 only)
2.16.1 DAILY TOTALIZER
2.16.2 RUNNING TOTALIZER
2.16.3 TOTALIZER DECIMAL POSITION
2 16.4 TOTALIZER MULTIPLIER
2 16.5 RESET DAILY TOTALIZER
2 16.6 RESET RUNNING TOTALIZER
A5E33329501 SITRANS LUT400 (HART) – INSTRUCTION MANUAL
3. MAINTENANCE AND DIAGNOSTICS
3 1 IDENTIFICATION
3. 1 .1 TAG
3.1.2 LONG TAG
3.1.3 DESCRIPTOR
3.1.4 MESSAGE
3.1.5 INSTALLATION DATE
3.1.6 PRODUCT
3.1.7 ORDER NO.
3.1.8 SERIAL NUMBER
3.1.9 FINAL ASSEMBLY NUMBER
3.1. 1 0 HARDWARE REV
3.1. 1 1 FIRMWARE REV
3.1. 1 2 LOADER REV
3.1. 1 3 MANUF. DATE
3.1. 1 4 ORDER OPTION
3.2 DIAGNOSTICS
3.2.1 ECHO PROFILE
3.2.2 TREND
3.2.3 MASTER RESET
3.2.4 POWER-ON RESETS
3.2.5 POWER-ON TIME
3.2.6 VIEW LOGS
3.2.6. 1 ALARMS
3.2.6.2 OCM
3.2.6.3 DAILY TOTALS
3.2.6.4 PV
3.2.7 PUMP RECORDS
3.2.7.1 RUN TIME RELAY 2
3.2.7.2 RUN TIME RELAY 3
3.2.7.3 RELAY PUMP 1
3.2.7.4 RELAY PUMP 2
3.2.8 TEMPERATURE PEAK VALUES
3.2.8. 1 HIGHEST VALUE
3.2.8.2 LOWEST VALUE
3.2.9 ECHO QUALITY
3.2.9. 1 FIGURE OF MERIT
3.2.9.2 CONFIDENCE
3.2.9.3 ECHO STRENGTH
3.2.9.4 NOISE AVERAGE
3.2.9.5 NOISE PEAK
3.3 MAINTENANCE
3.3.1 TRANSDUCER ENABLE
3.3.2 BACKUP CONTROL
3.3.3 REMAIN. DEV. LIFE
3.3.3. 1 LIFETIME EXPECTED
3.3.3.2 TIME IN OPER.
3.3.3.3 REMAIN. LIFETIME
3.3.3.4 REMINDER ACTIV.
3.3.3.5 REMIND. 1 (REQ.)
3.3.3.6 REMIND. 2 (DEM.)
3.3.3.7 MAINT STAT
3.3.3.8 ACK STATUS
SITRANS LUT400 (HART) – INSTRUCTION MANUAL Page 281