Report +12V O/Load; Display Lan O/Load; Report Lan O/Load; Horn Speaker Options - Bosch solution 6000 Installation Manual

Display +12v O/Load
Setting this option allows the keypad to display a system
trouble message when the current load on the +12 V
terminal exceeds its maximum rating of 1Amp.

Report +12v O/Load

Setting this option will cause the panel to send an
Overcurrent Trouble report to the base station when the
current load on the +12 V terminal exceeds its maximum
rating of 1Amp.

Display LAN O/Load

Setting this option allows the keypad to display a system
trouble message when the current load on the LAN+
terminal exceeds its maximum rating of 1Amp.

Report LAN O/Load

Setting this option will cause the panel to send an
Overcurrent Trouble report to the base station when the
current load on the LAN+ terminal exceeds its maximum
rating of 1Amp.
H O R N S P E A K E R O P T I O N S
System > Siren >

Tone

This menu allows you to customise the tone that is
emitted from the horn speaker when a non-fire alarm is
triggered. By changing the tone and speed, it is possible
to program a unique siren sound for each system when
you are installing a number of them in close proximity to
each other.
1) Press [MENU] + [7] + [4] + [0]. The keypad will
display the current siren tone.
Tone
1. . . . . . . . . . . . . 7
-------------  ---------
Press  OK to SAVE
2) Use the up and down arrow keys to change the the
siren tone.
3) To test the new siren tone press [ON] to sound the
siren and press [OFF] to turn the siren off.
4) Repeat Steps 2 and 3 until the desired siren tone is
achieved then press [OK] to save and exit, or press
[MENU] to exit without saving.
Only outputs programmed as Event Type 36 and or
i
37 will be affected by this menu option.
Note
Bosch Security Systems 07/14 BLCC610I
System > Siren >

Speed

This menu allows you to customise the speed of the siren
tone when a non-fire alarm is triggered. By changing the
tone and speed, it is possible to program a unique siren
sound for each system when you are installing a number
of them in close proximity to each other.
1) Press [MENU] + [7] + [4] + [1]. The keypad will
2) Use the up and down arrow keys to change the
3) To test the new siren speed press [ON] to sound the
4) Repeat Steps 2 and 3 until the desired siren tone is
 MENU 7-4-0
i
Note
System > Siren >

Volume

(*** System Wide Parameter ***)
This menu allows you to program the volume level of the
radio key speeker beeps which are heard when the system
is armed and disarmed using a radio keyfob.
1) Press [MENU] + [7] + [4] + [2]. The keypad will
2) Using the numeric keys, enter the new volume
3) Press [OK] to save and exit or press [MENU] to exit
i
Note
Solution 6000
Installation Manual

display the current siren speed.
Speed
S. . . . . . . . . . . . . F
-------------  ---------
Press  OK to SAVE
siren speed.
siren and press [OFF] to turn the siren off.
achieved then press [OK] to save and exit, or press
[MENU] to exit without saving.
Only outputs programmed as event type 36 and or
37 will be affected by this menu option.
display the current siren volume (default = 15).
Volume
15
Press 0-9 OK to SAVE
level. Valid entries are 0 to 15 where 15 = the
loudest volume and 0 = no speeker beeps.
without saving.
Only outputs programmed as Event Type 36, horn
speaker with beeps will be effected by this menu
option.
System Programming

 MENU 7-4-1
-
  MENU 7-4-2
1 5
11-9