H3C S5100-SI series Quick Start Manual
  1. Manuals
  2. Brands
  3. H3C Manuals
  4. Network Router
  5. H3C S5100-SI
  6. Quick start manual
H3C S5100-SI series Quick Start Manual

H3C S5100-SI series Quick Start Manual

Hide thumbs Also See for S5100-SI series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operating Manual, Installation Manual
H3C S5100-SI/EI Series
Ethernet Switches

Quick Start

Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Manual Version: T2-08018B-20070522-C-1.02

Advertisement

Table of Contents
loading

Related Manuals for H3C S5100-SI series

Summary of Contents for H3C S5100-SI series

  • Page 1: Quick Start

    H3C S5100-SI/EI Series Ethernet Switches Quick Start Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Manual Version: T2-08018B-20070522-C-1.02...
  • Page 2 Copyright © 2007, Hangzhou H3C Technologies Co., Ltd. and its licensors All Rights Reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co., Ltd. Trademarks H3C,...

  • Page 3: About This Manual

    About This Manual Related Documentation In addition to this manual, each H3C S5100-SI/EI Series Ethernet Switches documentation set includes the following: Manual Content H3C S5100-SI/EI Series It is used for assisting the users Ethernet Switches Operation in data configurations and...
  • Page 4 Chapter Contents Introduces the installation preparation and 2 Preparing for precaution of S5100-SI/EI Series Ethernet Installation Switches. Introduces the procedures to install an S5100-SI/EI Series Ethernet Switch, 3 Installing the Switch including the setup of the mainframe, cards and cables. 4 Lightning Protection Introduces lightning protection of of the Switch...
  • Page 5 Symbols Convention Description Means reader extremely careful. Improper operation may cause bodily Warning injury. Means reader careful. Improper operation may cause data loss or damage Caution to equipment. Note Means a complementary description. Environmental Protection This product has been designed to comply with the requirements on environmental protection.

  • Page 6: Table Of Contents

    1.1 Preface................1-1 1.2 LEDs ..................1-4 1.3 System Features of the S5100 Series .......1-8 1.3.1 System Features of the S5100-SI Series....1-8 1.3.2 System Features of the S5100-EI Series....1-9 1.4 Ordering SFP Interface Modules ........1-16 1.5 Ordering 10 G Stack Interface Modules ......1-18 1.6 Ordering Stack Cables.............1-18...
  • Page 7 Quick Start H3C S5100-SI/EI Series Ethernet Switches Table of Contents 3.1.4 Use Front Mounting Ears and a Tray ......3-8 3.1.5 Use Front and Rear Mounting Ears......3-9 3.1.6 Use Front Mounting Ears and Guide Rails....3-13 3.2 Desk Mounting ..............3-16 3.3 Wall Mounting ..............3-17 3.4 Magnet Mounting .............3-20...

  • Page 8: Chapter 1 Product Overview

    H3C S5100 series) are Gigabit Ethernet switching products developed by H3C Technology Co., Ltd. The H3C S5100 series provide a variety of service features. The H3C S5100 series are designed as convergence and access devices for intranets and metropolitan area networks (MANs), and can also be used for connecting data center server clusters.
  • Page 9 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview Table 1-1 H3C S5100-SI/EI series 10/100/1 000Base 1000Base- Console Series Model autosen X SFP port port sing Ethernet port S5100-8P-SI S5100-16P-SI S5100-S S5100-24P-SI S5100-48P-SI S5100-8P-EI S5100-16P-EI S5100-24P-EI S5100-48P-EI S5100-26C-EI...
  • Page 10 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview Table 1-2 Mapping relations between the ports forming the Combo port 10/100/1000Base-T 1000Base-X Model autosensing SFP port Ethernet port S5100-16P-SI S5100-16P-EI S5100-16P-PWR-EI S5100-24P-SI S5100-24P-EI S5100-26C-EI S5100-26C-PWR-EI S5100-48P-SI S5100-48P-EI S5100-50C-EI...

  • Page 11: Leds

    Chapter 1 Product Overview 1.2 LEDs Note: For the descriptions on the Ethernet port status LEDs and Ethernet port mode LEDs (MODE) of the S5100 series, see H3C S5100-SI/EI Series Ethernet Switches Installation Manual. Only the S5100-24P-EI, S5100-48P-EI, S5100-26C-EI, S5100-50C-EI, S5100-26C-PWR-EI, and S5100-50C-PWR-EI Ethernet switches provide DC power LEDs.
  • Page 12 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview Table 1-3 Description on the LEDs of the S5100-SI/EI series Mark Status Description Yellow, ON The switch is starting. The switch has been normally Green, ON started. The system is performing...
  • Page 13 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview Mark Status Description The module has not been installed or connected. The module has been installed Green, ON and connected. Modul 1 (or The module is receiving or Green, blinking e LED sending data.
  • Page 14 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview Mark Status Description A “1” is displayed. Unit Green, A “C” is displayed on command switch. An “S” is displayed on member Clust switch. Green, mana A “c” is displayed on candidate geme switch.

  • Page 15: System Features Of The S5100 Series

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview 1.3 System Features of the S5100 Series 1.3.1 System Features of the S5100-SI Series Table 1-4 System features of the S5100-SI series S5100-8P-S S5100-16P- S5100-24 S5100-48P- Item P-SI Dimensi 43.6 ×...

  • Page 16: System Features Of The S5100-Ei Series

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview S5100-8P-S S5100-16P- S5100-24 S5100-48P- Item P-SI power 16 W 25 W 39 W 78 W consum ption Operati 0°C to 45°C (32°F to 113°F) tempera ture Relative humidit 10% to 90%...
  • Page 17 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview S5100-8P- S5100-16P- S5100-24 S5100-48 Item P-EI P-EI 24 × 48 × 8 × 16 × 10/100/10 10/100/10 10/100/100 10/100/1000 00Base-T 00Base-T 0Base-T Base-T autosensin autosensin autosensin autosensing g Ethernet...
  • Page 18 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview S5100-8P- S5100-16P- S5100-24 S5100-48 Item P-EI P-EI Relative humidity 10% to 90% (noncond ensing) Table 1-6 System features of the S5100-EI series (2) Item S5100-26C-EI S5100-50C-EI Dimensio 43.6 × 440 × 300 mm (1.7 × 17.3 × 11.8 in.) (H ×...
  • Page 19 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview Item S5100-26C-EI S5100-50C-EI The S5100-EI series support AC input and DC input. AC input: Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60Hz Power supply Max voltage range: 90 VAC to 264 VAC, 47 Hz to 63...
  • Page 20 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview Table 1-7 System features of the S5100-EI series (3) S5100-16 S5100-8P S5100-26C- S5100-50C- Item P-PWR-E -PWR-EI PWR-EI PWR-EI 43.6 × 43.6 × Dimensio 300 × 220 300 × 260 43.6 ×...
  • Page 21 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview S5100-16 S5100-8P S5100-26C- S5100-50C- Item P-PWR-E -PWR-EI PWR-EI PWR-EI The S5100-EI series support AC input and DC input. AC input: Rated voltage range: 100 VAC to 240 VAC, 50 Hz or...
  • Page 22 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview S5100-16 S5100-8P S5100-26C- S5100-50C- Item P-PWR-E -PWR-EI PWR-EI PWR-EI Operating temperatu 0°C to 45°C (32°F to 113°F) Relative humidity 10% to 90% (noncond ensing) S5100-8P-PWR-EI, S5100-16P-PWR-EI, S5100-26C-PWR-EI, and S5100-50C-PWR-EI Ethernet switches provide over-temperature protection.

  • Page 23: Ordering Sfp Interface Modules

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview PoE protection PoE restoration Item temperature (°C) temperature (°C) S5100-26C-PWR-EI S5100-50C-PWR-EI 1.4 Ordering SFP Interface Modules Table 1-9 Ordering information for the SPF interface modules Item Model SFP-FE-SX-MM1310-A SFP-FE-LX-SM1310-A...
  • Page 24 XENPAK optical modules XENPAK-LX-SM1310 XENPAK-LH40-SM1550 Note: You are recommended to use H3C's optical modules for the S5100-SI/EI series Ethernet switches. Only the S5100-26C-EI, S5100-50C-EI, S5100-26C-PWR-EI, and S5100-50C-PWR-EI switches support XENPAK and XFP optical modules, but these switches do not support the XFP modules that require -5.2 V power supply.

  • Page 25: Ordering 10 G Stack Interface Modules

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview 1.5 Ordering 10 G Stack Interface Modules Table 1-10 Ordering information for 10 G stack interface modules Model No. Description Single-port 10 G Ethernet stack LS5M1XS1PA interface board (STACK)

  • Page 26: Ordering Dc Power Cords

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview 1.7 Ordering DC Power cords Table 1-12 Ordering information for DC power cords Model No. Length Description CAB-48V 2 m (6.6 Power cord 14AWG 2 m Pwr-2m-T2.5^2 ft.) CAB-RPS Non 2 m (6.6...

  • Page 27: Chapter 2 Preparing For Installation

    Quick Start Chapter 2 Preparing for H3C S5100-SI/EI Series Ethernet Switches Installation Chapter 2 Preparing for Installation 2.1 Safety Precautions To avoid any device impairment or bodily injury caused by improper use, observe these rules: Before cleaning the switch, unplug the power plug from the switch first.

  • Page 28: Temperature/Humidity

    Quick Start Chapter 2 Preparing for H3C S5100-SI/EI Series Ethernet Switches Installation The rack or table/workbench has a good ventilation system. The rack is sturdy enough to support the device and its accessories. The rack or table/workbench is well earthed.

  • Page 29: Cleanness

    Quick Start Chapter 2 Preparing for H3C S5100-SI/EI Series Ethernet Switches Installation 2.2.2 Cleanness Dust is a hazard to the operating safety of your device. The dust accumulated on the chassis can be adsorbed by static electricity and result in poor contact of metal connectors or metal contact points.

  • Page 30: Electromagnetic Susceptibility

    Quick Start Chapter 2 Preparing for H3C S5100-SI/EI Series Ethernet Switches Installation Maximum concentration (mg/m 0.05 0.01 2.2.3 Electromagnetic Susceptibility The operation of your switch can be affected by external interferences, such as conducted emission by capacitance coupling, inductance coupling, electromagnetic wave radiation, and common impedance (including the grounding system) coupling, and leads (power cords, signaling cables and output wires).

  • Page 31: Installation Tools

    Quick Start Chapter 2 Preparing for H3C S5100-SI/EI Series Ethernet Switches Installation When the extended optical interface cards on your switch are operating, do not stare into the optical ports because the laser light emitted by the optical fiber can hurt your retina.

  • Page 32: Chapter 3 Installing The Switch

    Otherwise, you will bear any consequence resulted from your actions without permission. 3.1 Rack-Mounting the Switch You can mount an H3C S5100 switch into a 19-inch standard rack in one of the following four ways: Use front mounting ears...
  • Page 33 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Table 3-1 Installation methods for a switch with a width of 440 mm or 436 mm (17.3 in. or 17.2 in.) Use front Use front Use front Use front...

  • Page 34: Introduction To Mounting Ear

    Guide rails purchased from H3C apply only to standard racks 1,000 mm (39.4 in.) deep. Use other supports to substitute for guide rails in the case of other rack depths.
  • Page 35 (1) Screw hole used to fix the mounting ear to the rack (Use one M6 screw) Figure 3-2 Appearance of a rear mounting ear When you install an H3C S5100 series switch into a 19-inch standard rack, you should select front mounting ears with a proper length (L1 as shown in Figure 3-1) according to the physical dimensions of the switch.
  • Page 36 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Table 3-3 Selection of mounting ear for the H3C S5100 series Ethernet Switches Configurati Configurati Physical on type of on type of Model dimensions (H x front rear...

  • Page 37: Introduction To Guide Rail

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch 3.1.2 Introduction to Guide Rail Figure 3-3 shows the appearance of a guide rail. Slotted hole 1 Cooling hole Slotted hole 2 Slotted hole 1: Used to fix the guide rail to the rear bracket. You can adjust the screw hole position according to the position of the switch.
  • Page 38 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Wear an ESD-preventive wrist strap to check the grounding and stability of the rack. Take out the screws which are packed together with the front mounting ears, and fix one end of mounting ears to the switch, as shown in Figure 3-4.

  • Page 39: Use Front Mounting Ears And A Tray

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Front square-holed bracket Front square-holed bracket Front mounting ear Front mounting ear Front panel Front panel Front Front mounting ear mounting ear Figure 3-5 Mounting the switch with front mounting ears and a tray 3.1.

  • Page 40: Use Front And Rear Mounting Ears

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch front brackets with crews and captive nuts, as shown in Figure 3-5. 3.1.5 Use Front and Rear Mounting Ears Follow these steps to install a switch into a 19-inch standard rack...
  • Page 41 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Note: There are three positions to mount a load-bearing screw on both sides of a switch. You should select a proper position according to the actual requirements. The rear mounting ears tightly contacted with the load-bearing screws can support the switch.
  • Page 42 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Hold the bottom of the switch with one hand and the front part of the switch with the other hand, and pull the switch into the cabinet gently, as shown in Figure 3-8.
  • Page 43 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Rear square- holed bracket Screw 1 Rear panel Rear mounting ear Screw 1: Load-bearing screw Figure 3-9 Effect diagram of front and rear mounting ea installation (1) Fix the other end of the front mounting ears to the front...

  • Page 44: Use Front Mounting Ears And Guide Rails

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Screw 1 Rear mounting ear Front panel Front mounting ear Front square-holed bracket Screw 1: Load-bearing screw Figure 3-10 Effect diagram of front and rear mounting ea installation (2) 3.1.6 Use Front Mounting Ears and Guide Rails...
  • Page 45 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Figure 3-11 Fix front mounting ears Install guide rails on the brackets on both sides of the cabinet with M5 self-tapping screws, as shown in Figure 3-12. Figure 3-12 Install guide rails...
  • Page 46 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Hold the two sides of the switch and slide it gently along the guide rails into the cabinet until it is located in a proper position, as shown in Figure 3-13. Ensure that the bottom side of the guide rails and the switch are in close contact.

  • Page 47: Desk Mounting

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Guide Rear panel rail Figure 3-14 Effect diagram of front mounting ear and guide ra installation Note: Ensure a clearance of 1U (44.45 mm, namely, 1.75 inches) between devices for the purpose of heat dissipation.

  • Page 48: Wall Mounting

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch The installation environment is drafty and a clearance about 10 cm (3.9 in) is reserved around the switch for heat dissipation. No heavy object is placed on the switch.
  • Page 49 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch (1) Outside edge of anchor kit Figure 3-16 Anchor kit II. Installation procedure The wall-mounting procedure is as follows: As shown in Figure 3-17, drill two holes having a diameter of 5 mm (0.2 in.) in the wall on the same horizontal line, with a...
  • Page 50 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch As shown in Figure 3-17, drive screws into the anchor kits, keeping the inside of screw head at least 1.5 mm (0.06 in.) away from the edge of the anchor kit so that the switch could hang on the screws securely.

  • Page 51: Magnet Mounting

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch 3.4 Magnet Mounting The S5100-8P-EI, S5100-16P-EI, S5100-8P-PWR-EI, and S5100-16P-PWR-EI series Ethernet switches support magnet mounting: I. Introduction to magnetic accessories Magnetic accessories consists of four permanent magnets and four M3*6 countersunk head screws, as shown in Figure 3-18.
  • Page 52 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch the dent of the switch bottom, and ensure that the permanent magnet and the switch are fastened reliably. Note: Remove the cushion, if any, from the dent before installation.
  • Page 53 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Caution: Apply magnet mounting to only the above four models. Otherwise, a falloff or mis-operation may occur. Select the installation location carefully. In the case of poor interface, magnet mounting may not be reliable.

  • Page 54: Connecting Power Cord And Grounding Wire

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch 3.5 Connecting Power Cord and Grounding Wire 3.5.1 Connecting AC Power Cord I. AC power socket (recommended) You are recommended to use a mono-phase three-wire power socket with a neutral point or a multi-function power socket for computers.
  • Page 55 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Install the power cord tie for the AC power cord. Insert the two ends of the power cord tie into the slots at both sides of the AC power input, and then set the power cord into the notch of the power cord tie.

  • Page 56: Connecting Dc Power Cord

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Caution: Before powering on the switch, you should properly connect the grounding wire. 3.5.2 Connecting DC Power Cord ＋ － NULL ＋ － NULL +: -48 V working ground —: -48 V to -60 V...
  • Page 57 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Figure 3-23 RPS DC power connector As shown in Figure 3-23, pass the two power cords through the air filter, insert them into the corresponding holes, and tighten them with screw 1 and screw 2. The positive and negative poles of the power cords must correspond to the silkscreen above the holes.

  • Page 58: Connecting Grounding Wire

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Figure 3-24 Fix the RPS DC power connector to the chassis Insert the connector into the DC socket directly. Use the flathead screwdriver to fix the connector with screw 1 and screw 2 (delivered with the switch), as shown in Figure 3-24.
  • Page 59 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Caution: You should properly connect the switch grounding wire since it is crucial to the lightning protection and electromagnetic shield (EMS) of your switch. The power input end of the switch is connected with a noise filter, whose central ground is directly connected to the chassis, forming the so-called chassis ground (commonly known as PGND).
  • Page 60 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch (1) Power input (2) Grounding screw (3) Protection grounding wire (4) Grounding strip Figure 3-25 Ground the switch through a grounding strip When there is no grounding strip but there is cement floor nearby where a grounding body is allowed to be buried, hammer an angle steel/steel pipe no shorter than 0.5 m (1.6 ft.) into the earth, with the...
  • Page 61 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch ( 2 ) ( 2 ) ( 3 ) ( 3 ) ( 1 ) ( 1 ) ( 4 ) ( 4 ) ( 5 ) ( 5 )
  • Page 62 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch (1 ) (1 ) (3 ) (3 ) (2 ) (2 ) (6 ) (6 ) (5 ) (5 ) (4 ) (4 ) (1) AC power socket...

  • Page 63: Connecting Console Cable

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch (11) (11) ( 5 ) ( 5 ) ( 5 ) ( 5 ) ( 10 ) ( 10 ) ( 10 ) ( 10 ) ( 9 )

  • Page 64: Connecting Console Cable

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Figure 3-29 Console cable Table 3-4 Console cable connector pinouts and mapping relation RJ-45 Signal Direction DB-9 ← ← ← → — → → → 3.6.2 Connecting Console Cable...
  • Page 65 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Step 1: Connect the DB-9 female connector of the Console cable to the serial port of the PC or the terminal device used to configure the switch. Step 2: Connect the RJ-45 connector of the Console cable to the Console port of the switch.

  • Page 66: Installing And Removing Optional Interface Modules

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch 3.7 Installing and Removing Optional Interface Modules 3.7.1 XFP Interface Module I. Appearance and front panel Figure 3-30 Appearance of an XFP interface module Figure 3-31 Front panel of an XFP interface module II.
  • Page 67 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Step 2: Loosen the mounting screws of the filler panel on the rear panel of the switch with a screwdriver and remove the filler panel. Step 3: Hold the fastening screws on the front panel of the XFP...
  • Page 68 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Note: Keep the removed filler panel properly for future use. When tightening the fastening screws at both sides of the optional module with a screwdriver or an electric screwdriver, make sure that the torque is not bigger than 0.4N•m.

  • Page 69: Stack Module

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Caution: When installing or removing an optional interface module, pay attention to the following points: Do not use too much force in the operation, and do not touch the surface-mounted components directly with your hands.

  • Page 70: Xenpak Optical Module

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Figure 3-34 Front panel of a stack module II. Installation and removal A stack module is installed and removed in the same way as you install and remove an XFP interface module. Refer to section 3.7.1 II.
  • Page 71 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Figure 3-36 Front panel of an XENPAK optical module II. Installation Step 1: Put on an ESD-preventive wrist strap and verify the ESD-preventive wrist strap properly grounded. Then take out the XENPAK optical module from the package.
  • Page 72 Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch (1): Switch (2): Filler panels for optional module slots (3): Small cover plate (removed) in the middle on the filler panel (4): Push-in direction (5): XENPAK optical module...

  • Page 73: Installing And Removing Dedicated Stack Cables

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Note: Keep the removed small cover plate properly for future use. When tightening the fastening screws at both sides of the optional module with a screwdriver or an electric screwdriver, make sure that the torque is not bigger than 0.4N•m.

  • Page 74: Installation

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch The dedicated stack cables for the S5100-EI series are available in three length specifications: 0.5 m (1.6 ft.), 1 m (3.3 ft.), and 3 m (9.8 ft.). You can choose the cables according to the specific needs.

  • Page 75: Verifying The Installation

    Quick Start H3C S5100-SI/EI Series Ethernet Switches Chapter 3 Installing the Switch Step 3: Pull out horizontally the plugs of the dedicated stack cable from the 10GE stack ports of the switches. Caution: The dedicated stack cables for the S5100-EI series are hot-swappable.

  • Page 76: Chapter 4 Lightning Protection Of The Switch

    Quick Start Chapter 4 Lightning Protection H3C S5100-SI/EI Series Ethernet Switches of the Switch Chapter 4 Lightning Protection of the Switch 4.1 Installation of Lightning Arrester for AC Power (Socket Strip with Lightning Protection) Caution: No lightning arrester is shipped with the switch. You need to purchase one if needed.
  • Page 77 Quick Start Chapter 4 Lightning Protection H3C S5100-SI/EI Series Ethernet Switches of the Switch Figure 4-1 Diagram of lightning arrester...
  • Page 78 Quick Start Chapter 4 Lightning Protection H3C S5100-SI/EI Series Ethernet Switches of the Switch Caution: Make sure that the lightning arrester is well grounded before using it for power. After the AC power cord of the switch is plugged into the socket of...

This manual is also suitable for:

H3c s5100-ei

Table of Contents