Table of Contents
Advertisement
The paper lev
3
Load the print material with the side to be printed on
the amount o
facing up.
empty, the in
Guidelines for Paper and Special Materials
When selecting or loading paper, envelopes, or other special
material, keep these guidelines in mind:
• Always use paper and other materials that conform with
the specifications listed under "Paper Specifications" on
To load pape
page C.6.
For envelopes, load them with the flap side down and with
side to be pri
the stamp area on the top left side.
• Attempting to print on damp, curled, wrinkled, or torn
paper can cause paper jams and poor print quality.
N
• Use only high quality copier grade paper for the best print
OTES
quality.
• If envelopes jam while printing, try reducing the number of
envelopes in the Multipurpose tray.
• Avoid paper with embossed lettering, perforations, or a
• If you want to print on previously printed paper from the
texture that is too smooth or too rough. Paper jams may
Multipurpose tray, the printed side should be facing down with an
occur.
uncurled edge toward the machine. If you experience problems
• Store paper in its ream wrapper until you are ready to use.
with the paper feeding, turn the paper around.
Place cartons on pallets or shelves, not on the floor. Do not
place heavy objects on top of the paper, whether it is
You can load
packaged or unpackaged. Keep it away from moisture, or
4
Squeeze the width guide and adjust it to the width of the
The top edge
other conditions that can cause it to wrinkle or curl.
print material without bending it.
front of the tr
• Store unused materials at temperatures between 15
and 30
o
C (59
o
F to 86
between 10 % and 70 %.
• During storage, you should use a moisture-proof wrap,
such as a plastic container or bag, to prevent dust and
moisture from contaminating your paper.
• Load special paper types one sheet at a time through the
Multipurpose tray to avoid paper jams.
• Only use materials specifically recommended for use in
For details ab
laser printers.
Paper" on pa
• To prevent special materials, such as transparencies and
label sheets from sticking together, remove them as they
print out.
5
Downloaded from ManualsPrinter.com Manuals
After loading paper, you need to set the paper type and size
• For envelopes:
for the Multipurpose tray. See page 2.21 for copying and
Printing to the Rear Output Slot
Using the rear output slot, paper comes out of the machine
face up.
3
Squeeze the width guide and adjust it to the width of the
print material without bending it.
Printing from the Multipurpose tray to the rear output slot
provides a straight paper path. Using the rear output slot
might improve the output quality with the following:
• envelopes
4
If you want the machine to stack the printed pages on the
• labels
rear output slot, open the rear door to use the rear output
• small custom-sized paper
slot.
Paper full
• postcards
N
: Make sure to open the rear output slot when you print on
• transparencies
OTE
transparencies. If not, they may tear while exiting the machine.
Paper empty
To use the rear output slot:
:
5
After printing, fold away the paper support extension and
1
Open the rear door by pulling it upward.
close the Multipurpose tray.
Tips on Using the Multipurpose Tray
• Load only one size of print material at a time in the
Multipurpose tray.
• To prevent paper jams, do not add paper when there is
still paper in the Multipurpose tray. This also applies to
other types of print materials.
• Print materials should be loaded face up with the top edge
o
F). The relative humidity should be
going into the Multipurpose tray first and be placed in the
center of the tray.
• Always load only the print materials specified in the
Specifications on page C.6 to avoid paper jams and print
W
: The fuser area inside of the machine becomes very
ARNING
quality problems.
hot when in use. Take care not to burn your fingers when you
• Flatten any curl on postcards, envelopes, and labels before
access this area.
loading them into the Multipurpose tray.
• When you print on 76 mm x 127 mm (3 x 5 in.) sized
media on the Multipurpose tray, open the rear door to use
the rear output slot.
• Make sure to open the rear door when you print on
transparencies. If not, they may tear while exiting the
machine.
3
o
C
(Face up)
Advertisement
Table of Contents
