Table of Contents
Advertisement
Auto Fit Copying
This special copy feature can be applied only when you place a
document on the document glass. If a document is detected in
A
the ADF, Auto Fit copying does not work.
Number of Copies
1
Using the No. of Copies button, you can select the number of
copies from 1 to 99.
2
1
Press No. of Copies.
Setting Copy Options
2
3
Press the scroll button ( or ) until the number you want
appears on the display.
The buttons on the control panel let you select all basic copy
options: darkness, document type, copy size, and number of
omize the copy settings including number of copies,
Pressing and holding the button allows you to quickly scroll
4
copies. Set the following options for the current copy job before
y size, darkness, and original type, by using the control
to the number you want.
pressing Start to make copies.
el buttons. See "Setting Copy Options" on page 5.7.
5
You can enter the value using the number keypad.
ear the settings, use the Clear/Stop button.
N
: If you press Clear/Stop while setting the copy options, all
OTE
3
Press Enter to save the selection.
of the options you have set for the current copy job will be
g a Document
ecessary, you can use special copy features, such as
canceled and returned to their default status. Or, they will
automatically return to their default status after the machine
er, Auto Fit, Clone, and 2Sides on 1pg copying.
N
OTE
completes the copy in progress.
Enlarge button while Auto Fit copying is enabled.
s Start to begin copying.
document glass or the Automatic Document
Using Special Copy Features
load an original document for copying,
Darkness
6
display shows the copy processing.
ending a fax. Using the ADF, you can load up to
2
47 ~ 105 g/m
, 12.5 ~ 28 lb) for one job. You
If you have an original document containing faint markings and
You can use the following copy features using the Special Copy
place only one sheet at a time on the document
:
dark images, you can adjust the brightness to make a copy that
button on the control panel:
2 Sides on 1 Page Copying
is easier to read.
n cancel the copy job during an operation. Press Clear/
• Off: Prints in normal mode.
and the copying will stop.
he ADF:
To adjust the contrast, press Darkness.
You can copy a 2-sided document on one side of one page of
• Clone: Prints multiple image copies from the original
n the document glass may cause black spots on the
A4-, Letter-, Legal-, Folio-, Executive-, B5-, A5-, or A6-sized
Each time you press the button, the LED labeled with the
ocuments smaller than 142 x 127 mm or
document on a single page. The number of images is
ut. Always keep it clean.
paper.
selected mode lights.
16 x 356 mm.
automatically determined by the original image and paper
the best scan quality, especially for colored or gray-scaled
You can choose from the following contrast modes:
size. See page 5.10.
pt to feed the following types of documents:
When you copy using this feature, the machine prints one side
s, use the document glass.
of the document on the upper half of the paper and the other
• Lighten: works well with dark print.
• Copy Collate: Sorts the copy job. For example, if you make
er or carbon-backed paper
side on the lower half without reducing the size of the original.
• Normal: works well with standard typed or printed
2 copies of a 3 page document, one complete 3 page
er
This feature is helpful for copying a small-sized document, such
documents.
document will print followed by the second complete
as a name card.
r thin paper
document. See page 5.10.
• Darken: works well with light print or faint pencil
ing Copies from the Automatic
markings.
creased paper
If the original document is larger than the printable area, some
• Auto Fit: Automatically reduces or enlarges the original
portions may not be printed.
image to fit on the paper currently loaded in the machine.
ument Feeder
lled paper
See page 5.11.
Original Type
This special copy feature can be applied only when you place a
• 2 sides in 1pg: Prints 2-sided original document on one
document on the document glass. If a document is detected in
aples and paper clips before loading
The Original Type setting is used to improve the copy quality by
sheet of paper. See page 5.11.
the ADF, 2 Sides on 1 Page copying feature does not work.
d the document face up into the ADF (Automatic
selecting the document type for the current copy job.
Downloaded from ManualsPrinter.com Manuals
ument Feeder). You can insert up to 50 sheets at a
• 2/4 Up: Prints 2/4 original images reduced to fit onto one
To select the document type, press Original Type.
y glue, ink, or correction fluid on the paper is
1
. Make sure that the bottom of the document stack
sheet of paper. See page 5.12.
Setting the Time Out Option
You can set the time the machine waits before it restores the
Poster Copying
default copy settings, if you do not start copying after changing
them on the control panel.
This special copy feature can be applied only when you place a
document on the document glass. If a document is detected in
1
the ADF, the Poster copying feature does not work.
Press Menu on the control panel until "Copy Setup"
appears on the top line of the display.
1
Place the document to be copied on the document glass and
2
close the cover.
Press the scroll button ( or ) to display "Timeout" on the
bottom line.
2
Press Special Copy.
3
Press Enter to access the menu item.
Place the document to be copied on the document glass,
3
Press Special Copy or the scroll button ( or ) until
and close the cover.
4
"Poster" displays on the bottom line.
Press the scroll button ( or ) until the status you want
appears on the display.
Press Special Copy.
4
Press Enter to make your selection.
You can select from 15, 30, 60, 120, and 180 (seconds).
Press Special Copy or the scroll button ( or ) until "Auto
Selecting "Off" means that the machine does not restore
5
If necessary, customize the copy settings, including number
Fit" appears on the bottom line.
the default settings until you press Start to begin copying,
of copies, darkness, and original type, by using the control
or Clear/Stop to cancel.
panel buttons. See "Setting Copy Options" on page 5.7.
Press Enter to make your selection.
5
Press Enter to make your selection.
N
: You cannot adjust the copy size using the Reduce/
If necessary, customize the copy settings, including number
OTE
Enlarge button when making a poster.
6
To return to Standby mode, press Clear/Stop.
of copies, darkness, and original type, by using the control
panel buttons. See "Setting Copy Options" on page 5.7.
6
Press Start to begin copying.
: You cannot adjust the copy size using the Reduce/
Your original document is divided into 9
portions. Each portion is scanned and
printed one by one in the following order:
Press Start to begin copying.
Place the document to be copied on the document glass and
5
Advertisement
Table of Contents
