Peg-Perego pilko switch Instruction Manual page 23

attached (fig_c).
4 FITTING THE REAR WHEELS: carefully distinguish
between the two rear wheels connected by the brake
cable: the rear left wheel features a slot that matches
a corresponding rib on the rear left chassis tube. Press
in the wheels until they click into place (fig_a) and
check that they are firmly attached (fig_b).
5 FITTING THE BASKET: insert the loops over the front
hooks (fig_a) and rear hooks (fig_b) and button down
the two flaps around the front tube (fig_c).
6 FITTING THE CUP HOLDER: insert the cup holder on
the corresponding peg and press down until it clicks
into place (fig_a). The cup holder can be attached to
either side of the chassis.
7 EXTENDABLE HANDLES: to extend the handles press
the top of the button and lift upwards the same time
(fig_a); to retract the handles press the bottom of the
button and push the handle downwards at the same
time (fig_b).
8 FIXED OR SWIVELLING FRONT WHEELS: lift the levers
to prevent the front wheels from swivelling (fig_a),
lower the levers to allow the front wheels to swivel
(fig_b). On uneven surfaces the wheels should be set
to their fixed position.
9 REAR WHEELS WITH CENTRAL BRAKE CABLE: press a
brake lever to immobilise the stroller (fig_a), lift the
lever to release it (fig_b).
10 MOUNTING THE SEAT TO THE CHASSIS: the reversible
seat can be attached to the chassis either facing
the person pushing the stroller (fig_a), or facing
forwards (fig_b), place the seat on the chassis so
that it is aligned with the relative symbols and press
downwards with both hands until you hear two clicks
confirming that it has locked into position. Ensure
the seat is correctly secured by attempting to pull it
upwards by gripping the front bar.
11 REMOVING THE SEAT FROM THE CHASSIS: move the
two levers in the direction of the arrow (fig_a) and lift
the two handles up (fig_b) until release. Pull the two
handles upwards until the seat is released. The seat
can be removed from and re-attached to the chassis
also when it is occupied by a child.
12 FRONT BAR: to attach the front bar, slide the
connections into the end of the armrests, press the
two side buttons and push the bar towards the seat
until it clicks into place (fig_a). To remove the front
bar press the two buttons and pull it outwards (fig_b).
Open the front bar at one side only so that the child
can be positioned in or removed from the seat more
easily.
13 BACKREST: to recline the backrest lift the lever (fig_a)
and choose one of the 4 positions (fig_b).
14 FOOTREST: to lower the footrest push the two levers
downwards and then push the footrest downwards
(fig_a); to raise the footrest lift it upwards (fig_b).
15 5-POINT SAFETY HARNESS: to attach the safety
harness, insert the two buckles of the waist strap
(with shoulder straps attached – arrow_a) into the
leg divider strap until it clicks into place (arrow_b). To
release, push the round button placed in center of the
buckle upwards (arrow_c) and pull the waist strap to
the sides (arrow_d).
16 To tighten the waist strap, pull on both sides in the
direction of the arrow (arrow_a). To loosen it do the
opposite. The waist strap can be tightened as far as
the safety lock (fig_b).
17 To adjust the height of the safety harnesses, release
the two buckles on the rear of the backrest.
Pull the shoulder straps towards you (arrow_a) until
the buckles are released and insert them in the
backrest loops (arrow_b). Remove the shoulder straps
from the sack (arrow_c) and insert them in the most
appropriate loop (arrow_d), then re-attach the two
buckles on the rear of the backrest (arrow_e) The
buckles are securely attached when a click is heard
(fig_f).
18 HOOD: to attach the hood insert the connections
into the sides of the seat (fig_a) and then fasten the
buttons on the rear of the backrest (fig_b). To remove
the hood: disengage the connections and unbutton
from the backrest. To raise the hood: pull it towards
you; to close the hood: push it back. To convert the
hood into a sun canopy, open the double zipper
(fig_c) and unfasten the buttons on the rear of the
backrest.
19 COVER: The same cover can be attached and used
with both the Navetta XL and the Pliko Switch stroller.
Unbutton the part under the cover (fig_a), detach the
Velcro (fig_b) and extend it (fig_c).
20 For the carriage version, lift the leg rest and fit the
cover over the front bar (fig_a), then fasten it behind
the leg rest with the Velcro (fig_b) and attach it to the
buttons on the hood with the elastic loops (fig_c).
21 For the stroller version, fasten the buttons on the
underside of the cover (fig_a), lower the leg rest and
fit the cover on (fig_b). Next, pass the cover under the
front bar (fig_c) and attach it with the buttons (fig_d).
22 RAIN CANOPY: position the rain canopy on the stroller
(fig_a) and insert the two lateral loops over the hood
buttons (fig_b).
23 Secure the rain canopy by attaching the elastic loop
to the rear uprights (fig_a) or to the front uprights
(fig_b), according to the seat position.
24 REAR LEDGE: the rear ledge makes it easier to
negotiate kerbs or level differences with the stroller
(fig_a) and can also be used to transport a second
child (fig_b). To use the stroller with two children,
apply the brakes, position the smaller child in the seat
and attach the safety harness (1). Grip the handles (2)
and help the second child to climb onto the ledge (3).
25 FOLDING: the stroller can be folded without the
seat, with the seat facing the person pushing the
stroller, or with the seat facing forwards. If the seat
is facing the person pushing the stroller: before
folding it, lower the backrest completely; if the seat is
facing forwards: before folding the stroller raise the
backrest, and once it is folded, lower it. To fold the
stroller set the front wheels to their fixed position
and close the hood, if fitted. Lift the two levers of the
handles together and push downwards to release the
side tubes (fig_a-b), pull the central handle upwards
(fig_c) until the safety catches engage (fig_d). When
folded the stroller will stand upright without support.
26 TRANSPORT: the stroller can be carried by the central
handle, keeping the front wheels fixed (fig_a) or by
the side handle (fig_b).
27 REMOVABLE LINING: with the backrest in its raised
position, detach the two elastic loops on the back
(fig_a), extract the four tabs to the sides (fig_b) and
detach the Velcro from the armrests (fig_c).
28 Slip the side lining off the hood tabs (fig_a), undo
the two buttons at the sides of the backrest (fig_b),
detach the two elastic loops of the sack from the
footrest (fig_c), remove the leg divider strap from the
top (by pushing it up from under the seat) (fig_d).
NAVETTA XL
INSTRUCTIONS FOR USE
29 HOOD: To attach the hood, fasten the clips (fig_a) and
then the buttons on the sides (fig_b) and, if present,
the back (fig_c).
30 COVER: The same cover can be attached and used
with both the Navetta XL and the Pliko Switch stroller.
Position the cover, button it on both sides (fig_a),
attach the cover flap by buttoning it to the cover
- 23 -