Digital Audio Input Setup - Onkyo TX-NR5007 Instruction Manual

First Time Setup—Continued

Digital Audio Input Setup

If you connect a component to a digital input jack, you
must assign that jack to an input selector. For example, if
you connect your CD player to the OPTICAL IN1 jack,
you should assign that jack to the CD input selector. By
default, the COAXIAL IN1 jack is assigned to the DVD/
BD input selector, although this can be changed.
Here are the default assignments.
Input selector
DVD/BD
VCR/DVR
CBL/SAT
GAME
AUX 1
AUX 2
TV/TAPE
TUNER
CD
PHONO
PORT
1 Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn't appear, make
sure the appropriate external input is
selected on your TV.
2 Use the Up and Down [q]/[w] but-
tons to select "1. Input/Output
Assign", and then press
[ENTER].
The "Input/Output Assign" menu
appears.
3 Use the Up and Down [q]/[w] but-
tons to select "4. Digital Audio
Input", and then press [ENTER].
The "Digital Audio Input" menu
appears.
56
Default assignment
(TX-NR3007) (TX-NR5007)
COAX1 COAX1
COAX2 COAX2
COAX3 COAX3
OPT1 OPT1
FRONT (Fixed) FRONT (Fixed)
- - - - - - - - - -
- - - - - OPT2
- - - - - (Fixed) - - - - - (Fixed)
OPT2 OPT3
- - - - - - - - - -
- - - - - - - - - -
1. Input/Output Assign
1. Monitor Out
2. HDMI Input
3. Component Video Input
4. Digital Audio Input
5. Analog Audio Input
1–4. Digital Audio Input
DVD/BD COAX1
VCR/DVR COAX2
CBL/SAT COAX3
GAME OPT1
AUX 1 FRONT
4
Use the Up and Down [q]/[w] but-
tons to select an input selector,
and use the Left and Right [e]/
[r] buttons to select "COAX1",
"COAX2", "COAX3", "OPT1",
"OPT2", "OPT3" (TX-NR5007), or
"- - - - - (analog)".
• When an HDMI IN is assigned to an
input selector in "HDMI Input
Setup" on page 54, the AV receiver
will select audio from HDMI IN as a
priority.
• Press the [ENTER] button when you
do not use the signal of audio from
the HDMI IN. The " " mark is dis-
played like "COAX1 ".
• "AUX 1" is used only for digital
input from the front panel terminals.
Examples:
If you connect your DVD player to the
OPTICAL IN 1 jack, set "DVD/BD" to
"OPT1".
If you want to listen to audio from the
component connected to the OPTICAL
IN 2 jack when the VCR/DVR input
selector is selected, set "VCR/DVR" to
"OPT2".
If you want to listen to audio from the
component connected to the
COAXIAL IN 1 jack when the CBL/
SAT input selector is selected, set
"CBL/SAT" to "COAX1".
For input selectors that you don't want
to assign a digital input jack, set to
"- - - - - (analog)".
5 Press the [SETUP] button.
The setup menu closes.
Notes:
• Available sampling rate for PCM signals from a
digital input (optical and coaxial) is 32/44.1/48/88.2/
96 kHz/16, 20, 24 bit.
• If you connect an input component (such as UP-A1
Dock that seated iPod) to the UNIVERSAL PORT
jack, you cannot assign any input to PORT selector.
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
*
*