Connecting A Recording Device Such As Md Recorder, Dat Deck, Cd Recorder Or Cassette Deck - Onkyo TX-NR1000 Instruction Manual

Connecting AV Components —Continued
Connecting a Recording Device such as MD Recorder, DAT Deck, CD Recorder
or Cassette Deck
• When connecting a MD recorder, DAT deck or CD recorder to the TX-NR1000/TX-NR5000E, make connections
using digital or analog terminals. Before making connections, refer to page 30 for correct connections.
• Connect a cassette or DAT tape deck to TAPE1, and an MD or CD recorder to TAPE 2.
• When you connect a cassette deck to the TX-NR1000/TX-NR5000E, be sure to use only analog audio terminals. In
the initial settings, no terminal of this unit is assigned to a REC terminal of the cassette deck. To achieve the assign-
ment, connect the REC terminal of the cassette deck to any of the AUDIO OUT 1 to 5 terminals and set the terminal
to "Tape 1 Rec Out" in the Audio Output Assign sub-menu (See page 91). In addition, you can switch the input source
"TAPE2" to MD or CDR. Press the [TAPE 2] button on the front panel to display "TAPE 2," then press the [TAPE 2]
button again and hold it for 3 seconds. This changes the display to "MD." If you wish to change it to "CDR," release
the button once, and press and hold it again for 3 seconds. This operation enables you to operate Onkyo's MD or CD
recorders with the remote controller of this unit (Please note that the
• When connecting to other terminals, remember to configure the audio input assignment in the Audio Assign sub-
menu (See page 94) and the audio output assignment in the Audio Output Assign sub-menu (See page 91).
• You can change the display name for the input source to represent the actual connected device (See page 97).
• When you want to perform analog recording of an audio signal or operate your
connections between the TX-NR1000/TX-NR5000E, you have to make analog audio signal connections. Con-
nect the audio output terminals on the source device to the AUDIO IN terminals on the TX-NR1000/TX-NR5000E
using analog audio cables (RCA/phono).
Example for connecting with the TAPE 1 as input
Cassette deck or DAT deck
When connecting to other digital audio ter-
minals or to other analog audio output ter-
minals, configure the audio output settings
accordingly using the Audio Output Assign
sub-menu (See page 91).
C DIGITAL IN D
OPTICAL
1 1
2 2
"Net-Tune"
3 3
is a trademark of
Onkyo Corporation.
4 4
ETHERNET
5 5
( Net-Tune )
6 6
1 1
2 2
OUT
A B C D
SURR R SURR BACK R
PRE OUT A
When connecting to other digital audio termi-
nals or to other analog audio output terminals,
configure the audio output settings accord-
ingly using the Audio Output Assign sub-
menu (See page 91).
MD recorder or CD recorder
Example for connecting to the TAPE 2 as input
AUDIO IN
DIGITAL
OPTICAL
F AUDIO IN G G
DIGITAL IN E MULTI H S VIDEO
- CH
COAXIAL R L R L
IN 1
FR
FL
PH 4 1
SUB C
5
2
GND
SR SL R L
1 6
3
SBR SBL
2 7 4
FR FL
3 8 5
SUB C
1 9 6
SR SL
2 4
1
SBR SBL
3 5 2
R
R L L
OUT
S VIDEO
MULTI G
- CH
IN 2
F
( ASSIGNABLE ) FRONT R CENTER FRONT L
AUDIO IN AUDIO OUT
DIGITAL
OPTICAL
connection is required).
-compatible Onkyo products via
When connecting to other audio
terminals within the same terminal
AUDIO OUT AUDIO OUT
DIGITAL ANALOG
section, configure the audio input
OPTICAL
R L
settings accordingly using the
Audio Assign sub-menu (See page
94).
COMPONENT J K
VIDEO I L
VIDEO
IN 1
IN 2
ANTENNA
COMPONENT VIDEO
IN 4
Y
Y
P B
P
B
HDMI, the HDMI logo
P R is a trademark
FM
or registered
75 trademarks of HDMI
IN 3
OUT 1
Licensing LLC.
P
R
Y
OUT 2
P
B
Y
AM
P
R
P
B
3
P
R
4
OUT OUT
VIDEO VIDEO S VIDEO
H I J K
SURR BACK L ( ASSIGNABLE ) SURR L
( SINGLE )
When connecting to other audio ter-
minals within the same terminal
section, configure the audio input
R L
settings accordingly using the
AUDIO OUT
DIGITAL
Audio Assign sub-menu (See page
ANALOG
COAXIAL
94).
RS 232
HDMI
IN 1
REMOTE
12V
CONTROL
TRIGGER
OUT
A
200mA MAX.
IN 2
B 100mA MAX.
C
100mA MAX.
D 100mA MAX.
E
100mA MAX.
MAIN
ZONE 2
OUT ZONE 3
IN
OUT
L
IR
39