Dolby Virtual Speaker Setup Sub-Menu - Onkyo TX-NR1000 Instruction Manual

Listening Mode Setup —Continued
e. Surr Bk Speaker
This option configures the surround back speakers to
use when playing the source. Select the speaker
terminals to which the speakers you want to use are
connected. This setting can be made when the
"(Speaker B) Surr Back" is set to "Main A" in the
Speaker Configuration sub-menu. However, when the
"(Speaker A) Surr Back" is set to "BTL for Front," "Bi-
Amp for Front," or "Not Used," this setting will not be
displayed.
• When the impedance setting for "Surr L/R A" or "Surr
L/R B" in the Speaker Impedance sub-menu is set to
"6 ohms" or "4 ohms," the available options will be
"A" and "B."
• When the settings for "(Speaker A) Surr Back" and
"(Speaker B) Surr Back" in the Speaker Configuration
sub-menu differ, the available options will be "A" and
"B."
A (Default): Outputs the source from the speakers
connected to the SURR BACK L/R SPEAKERS A
terminals.
B: Outputs the source from the speakers connected to
the SURR BACK L/R SPEAKERS B terminals.
A+B: Outputs the source from the speakers connected
to the SURR BACK L/R SPEAKERS A and SURR
BACK L/R SPEAKERS B terminals.
f. Subwoofer
This option configures the subwoofer to use when
playing the source. Select the terminal to which the
subwoofer you want to use is connected. This setting
can be made when the "(Speaker A) Subwoofer" is set
to an option other than "Not Used" in the Speaker
Configuration sub-menu. However, when the "(Speaker
B) Subwoofer" is set to an option other than "Main A"
in the Speaker Configuration sub-menu, the available
options will be "A" or "Not Used."
A (Default): Outputs the source only from the
subwoofer connected to the SUBWOOFER PRE OUT
A terminal.
B: Outputs the source only from the subwoofer
connected to the SUBWOOFER PRE OUT B terminal.
A+B: Outputs the source from the subwoofers
connected to the SUBWOOFER PRE OUT A and
SUBWOOFER PRE OUT B terminals.
Not Used: No subwoofers are used for playback.
Dolby Virtual Speaker Setup Sub-
menu
This sub-menu allows you to configure the playback
options when you use the Dolby Virtual Speaker effect.
a. Mode (2ch or 3ch only)
This option allows you to configure the width of a virtual
sound image which is simulated using two or three
speakers while you use the Dolby Virtual Speaker effect.
Wide: The breadth of the sound image is emphasized.
116
Reference (Default): The general 5.1ch surround
sound is simulated.
b. Front Speaker
This option configures the front speakers to use when
playing the source. Select the speaker terminals to
which the speakers you want to use are connected. This
setting can be made when the "(Speaker B) Front L/R"
is set to "Main A" in the Speaker Configuration sub-
menu.
• When the impedance setting for "Front L/R A" or
"Front L/R B" in the Speaker Impedance sub-menu is
set to "6 ohms" or "4 ohms," the available options will
be "A" and "B."
A (Default): Outputs the source from the speakers
connected to the FRONT L/R SPEAKERS A terminals.
B: Outputs the source from the speakers connected to
the FRONT L/R SPEAKERS B terminals.
A+B: Outputs the source from the speakers connected
to the FRONT L/R SPEAKERS A and FRONT L/R
SPEAKERS B terminals. Note that this option is not
available when the front speakers are in Bi-amp or in
BTL configuration.
c. Center Speaker
This option configures the center speaker to use when
playing the source. Select the speaker terminal to which
the speaker you want to use is connected. This setting
can be made when the "(Speaker B) Center" is set to
"Main A" in the Speaker Configuration sub-menu.
• When the impedance setting for "Center A" or
"Center B" in the Speaker Impedance sub-menu is set
to "6 ohms" or "4 ohms," the available options will be
"A" and "B."
A (Default): Outputs the source from the speaker
connected to the CENTER SPEAKERS A terminal.
B: Outputs the source from the speaker connected to the
CENTER SPEAKERS B terminal.
A+B: Outputs the source from the speakers connected
to the CENTER SPEAKERS A and CENTER
SPEAKERS B terminals.
d. Surr L/R Sp
This option configures the surround speakers to use
when playing the source. Select the speaker terminals to
which the speakers you want to use are connected. This
setting can be made when the "(Speaker B) Surr L/R" is
set to "Main A" in the Speaker Configuration sub-menu.
• When the impedance setting for "Surr L/R A" or "Surr
L/R B" in the Speaker Impedance sub-menu is set to
"6 ohms" or "4 ohms," the available options will be
"A" and "B."
A (Default): Outputs the source from the speakers
connected to the SURR L/R SPEAKERS A terminals.
B: Outputs the source from the speakers connected to
the SURR L/R SPEAKERS B terminals.