Connection Examples - Onkyo TX-NR1000 Instruction Manual

Speaker Placement —Continued

Connection Examples

The TX-NR1000/TX-NR5000E has two speaker terminal blocks for speaker system [A] and [B]. This allows you to
build two 7.1 ch home theater systems, and various speaker placements and connections are also available. For
example, some channels of either speaker system can be used for another room (Zone 2), or you can select one of two
speaker systems for playback according to the source.
When you use two speaker systems, you have to associate the speakers with the zone (e.g., Main A, Main B, etc.).
After making the association, for example, pressing the "MAIN A" button on the remote controller will output the
source from the speakers configured as "Main A."
Here are some examples of speaker placement and zone association. These examples can be your reference when you
build your own home theater system. The illustration on the right represents the actual settings displayed corresponding to
each example. For details on configuring speaker placement and zone association, see page 88.
*In the following illustrations, white speakers denote speaker system [A] and gray ones denote speaker system [B].
* Key to abbreviations:
FL : Front left speaker; FR : Front right speaker; C : Center speaker; SL : Surround left speaker; SR : Surround right speaker;
SBL : Surround back left speaker; SBR : Surround back right speaker; SW : Subwoofer
When you wish to configure 7.1 ch speaker system in the main room A only, the initial setting can be used without
any modification.
Main room A: 7.1 ch speaker system; Main room B: 7.1ch speaker system
SW
FL C FR
Main room A
SBL SBR
• Set all the zone parameters for speaker system [A] to "Main A."
• Set all the zone parameters for speaker system [B] to "Main B."
• Pressing the [MAIN A] or [MAIN B] button causes the sound to be output
from the speaker system associated with the zone button. Both speaker
systems cannot be selected simultaneously.
* If you set all the zone parameters for speaker system [B] to "Main A" and play a single
source, the same audio signal will be output from both speaker systems [A] and [B].
Main room A: 7.1 ch speaker system; Main room B: 5.1 ch speaker system; Sub room (Zone 2): 2 ch
speakers
SW
FR
FL C
Main room A
SBL SBR
• Set all the zone parameters for speaker system [A] to "Main A." Set the zone parameters for
speaker system [B] to "Main B" and "Zone 2" accordingly.
• Both main room A and B cannot be used simultaneously. However, while either of the main
rooms is used, you can enjoy a different source in Zone 2.
• Note that when you use Zone 2, the surround back speakers for main room A cannot be used
since Zone 2 uses the surround back speaker circuit for main room A.
22
SW
FL C FR
Main room B
SBL SBR
SW
FL
FR
FL C
Zone 2
Main room B
1-1.Speaker Config
=====================
a.Front L/R :Main A
b.Center
c.Surr L/R
d.Surr Back
:Main A 2ch
e.Subwoofer :Main A
f.Front L/R :Main B
g.Center
h.Surr L/R
i.Surr Back
:Main B 2ch
j.Subwoofer :Main B
1-1.Speaker Config
=====================
FR
Speaker A
a.Front L/R :Main A
b.Center
c.Surr L/R
d.Surr Back
:Main A 2ch
e.Subwoofer :Main A
Speaker B
f.Front L/R :Main B
g.Center
h.Surr L/R
i.Surr Back
Powered
:Powered Zone 2
j.Subwoofer :Main B
Zone 2
Speaker A
:Main A
:Main A
Speaker B
:Main B
:Main B
:Main A
:Main A
:Main B
:Main B
Main B