Connecting A Dbs Tuner, Dbs Tv, Or Bs/Cs Tuner - Onkyo TX-NR1000 Instruction Manual

Connecting AV Components —Continued

Connecting a DBS Tuner, DBS TV, or BS/CS Tuner

• When connecting a DBS tuner, DBS TV, or BS/CS tuner to the TX-NR1000/TX-NR5000E, make connections for
video and audio signals using digital and analog terminals. Before making connections, refer to page 30 for correct
connections.
• This section shows the connection example when you use the VIDEO 4 or VIDEO 5 as an input. In this case, you do
not need additional configurations. When connecting to other terminals within the same terminal section on the
TX-NR1000/TX-NR5000E, remember to configure the audio input assignment in the Audio Assign sub-menu (See
page 94) and the video input assignment in the Video Assign sub-menu (See page 95). When you use the S VIDEO
terminal for connection, you should configure the Video Assign sub-menu.
• You can change the display name for the input source to represent the actual connected device (See page 97).
• For a model without a slot for the HDMI terminal, when you connect a BS/CS tuner or LD player to the COMPO-
NENT terminals, be sure to use the COMPONENT terminals to connect a TV or projector.
*For more information on the HDMI interface, see page 43.
*For more information on the i.LINK (AUDIO) interface, see page 40.
Example for connecting with the VIDEO 4 as input
When connecting to other audio ter-
minals within the same terminal sec-
tion, configure the audio input
settings accordingly using the Audio
Assign sub-menu (See page 94).
C DIGITAL IN D
OPTICAL
1 1
2 2
"Net-Tune"
3 3
is a trademark of
Onkyo Corporation.
4 4
ETHERNET
5 5
( Net-Tune )
6 6
1 1
2 2
OUT
A B C D
SURR R SURR BACK R
R L
AUDIO OUT AUDIO OUT
DIGITAL
COAXIAL
When connecting to other When connecting to other
audio terminals within the video terminals within the
same terminal section, con- same terminal section, con-
figure the audio input set- figure the video input set-
tings accordingly using the tings accordingly using the
Audio Assign sub-menu (See Video Assign sub-menu
page 94). (See page 95).
Example for connecting with the VIDEO 5 as input
AUDIO OUT AUDIO OUT
DIGITAL ANALOG
OPTICAL
R L
DIGITAL IN E MULTI F AUDIO IN G G H S VIDEO
- CH
R L R L
COAXIAL IN 1
FR
FL
PH 4 1
SUB C
5 2
GND
R L
SR SL
1 6 3
SBR SBL
2 7
4
FR FL
3 8
5
SUB C
1 9 6
SR SL
2 4 1
SBR SBL
3 5 2
R L R L
OUT
S VIDEO
G
MULTI
- CH
IN 2
F
( ASSIGNABLE ) FRONT R CENTER FRONT L
VIDEO
OUT
When connecting to other video ter-
minals within the same terminal sec-
VIDEO
tion, configure the video input
OUT
settings accordingly using the Video
Assign sub-menu (See page 95).
COMPONENT K
VIDEO I J L
VIDEO
IN IN IN 1
IN 2
COMPONENT VIDEO ANTENNA
IN 4
Y
Y
P
B
P
B
HDMI, the HDMI logo
P
R is a trademark
FM or registered
75
trademarks of HDMI
OUT 1 IN 3
Licensing LLC.
P R
Y
OUT 2
P B
Y
AM
P
R
P
B
3
P
R
4
OUT OUT
VIDEO VIDEO S VIDEO
H I J K
SURR BACK L ( ASSIGNABLE ) SURR L
RS 232
HDMI
IN 1
REMOTE
12V
CONTROL
TRIGGER
OUT
A
200mA MAX.
IN 2
B 100mA MAX.
C
100mA MAX.
D 100mA MAX.
E
100mA MAX.
MAIN
ZONE 2
ZONE 3
OUT
IN OUT
L
IR
37