Connecting The Power/Basic Operations; Turning On The Power; Operating On The Tx-Nr1000/Tx-Nr5000E - Onkyo TX-NR1000 Instruction Manual

Connecting the Power/Basic Operations

• Before you plug in the TX-NR1000/TX-NR5000E, confirm that all connections have been made properly.
• Turning on the power may cause a momentary power surge, which might interfere with other electrical equipment
on the same circuit, such as computers. If this happens, use a wall outlet on a different circuit.
(All models other than USA, Canadian, and Australian models)
The TX-NR1000/TX-NR5000E is shipped with the main power (POWER) switch in the on position (
the power cord is plugged in for the first time, the TX-NR1000/TX-NR5000E will automatically enter the standby
state and the [STANDBY] indicator will light (same condition after step 2 below on the left coloumn).
Input source buttons
STANDBY/ON
STANDBY indicator
STANDBY/ON
STANDBY
DISPLAY
( )
REC / ZONE 3 RED
MAIN ( BLUE )
ZONE 2 ( GREEN )
DVD VIDEO 1
PURE AUDIO
LISTENING AUDIO
MODE SELECTOR TONE ZONE
PHONES
TUNING
MODE MEMORY DIMMER LEVEL
CLEAR
(USA, Canadian, and Australian models)

Turning on the Power

1 Plug the power cord into an AC
wall outlet.
(USA, Canadian, and Australian
models)
The [STANDBY] indicator will light up.
POWER (Other models)
Press the [POWER] switch to set
the TX-NR1000/TX-NR5000E to
ON OFF
standby state.
STANDBY
The [STANDBY] indicator will light up.
2 Press the [STANDBY/ON] button
to turn on the TX-NR1000/
STANDBY/ON
TX-NR5000E.
The display will light up and the
[STANDBY] indicator will turn off.
STANDBY
If you press the [STANDBY/ON] button
again, the TX-NR1000/TX-NR5000E
Turn off
returns to the standby state.
Note:
Any components connected via
on when the remote controller's [ON] button is pressed.
50
MASTER VOLUME
MASTER VOLUME
TAPE 1 TAPE 2 TUNER PHONO C D NET AUDIO
VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7 OPEN
2 SELECT/ PRESET SETUP CONTROL / TUNING REC/ ZONE 3 VIDEO 7 INPUT
DIGITAL S VIDEO VIDEO L AUDIO R
EXIT LEVEL
PUSH TO ENTER PUSH TO ENTER
To wall outlet
will also be turned
Input source buttons
STANDBY/ON
STANDBY indicator
MASTER VOLUME
STANDBY/ON
STANDBY
POWER
DISPLAY TAPE 1 TAPE 2 TUNER PHONO C D
REC / ZONE 3 ( RED )
MAIN ( BLUE )
ZONE 2 ( GREEN )
DVD VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6
ON OFF
PURE AUDIO
LISTENING AUDIO
MODE SELECTOR TONE ZONE 2 SELECT/ PRESET SETUP CONTROL / TUNING REC/ ZONE 3
PHONES
TUNING
MODE MEMORY RT/ PTY/ TP LEVEL EXIT LEVEL
CLEAR PUSH TO ENTER PUSH TO ENTER
To wall outlet
POWER
(Other models)
Operating on the TX-NR1000/
TX-NR5000E
1 Select an input source.
Press the input source button.
DISPLAY TAPE 1 TAPE 2
*You cannot listen to a source in main
TUNER PHONO C D NET AUDIO room A, and to another source in main
room B.
DVD VIDEO 1 VIDEO 2 VIDEO 3
VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7
2 Start playing the device selected.
When playing a picture device such as a
DVD player, you need to switch input to
a monitor such a TV set.
Some picture-playing devices such as a
DVD-type game machine may also
require setting of sound output. Refer to
the manual of the device connected.
3
Adjust the volume level with the
[MASTER VOLUME] dial.
You can adjust the volume level in the
MASTER VOLUME
range from – ∞ , –81.5 dB to 18.0 dB
(Max) (when Relative is selected in the
Volume Setup sub-menu).
Hint:
TX-NR1000/TX-NR5000E is a product
for users to enjoy home theater, so it is
equipped with a wide range of volume
levels. Please fine tune the volume level
aaccording to your preferences.
). When
ON
MASTER VOLUME
NET AUDIO
VIDEO 7 OPEN
VIDEO 7 INPUT
DIGITAL S VIDEO VIDEO L AUDIO R