Connecting; Compatible Av Components; Connections For Remote Control ( ) - Onkyo TX-NR1000 Instruction Manual

Connecting

The terminal on the TX-NR1000/TX-NR5000E is
for connecting other Onkyo components equipped with
the same terminal. When a component is connected
to the terminal, it can be operated by the remote
controller supplied with the TX-NR1000/TX-NR5000E.
In addition, when you connect a component to the
terminal, you can also perform the system operations
given below.
Power on/ready function
When the TX-NR1000/TX-NR5000E is in the standby
state, if an -connected component is turned on, the
TX-NR1000/TX-NR5000E also turns on and the input
source selected at the TX-NR1000/TX-NR5000E
automatically switches to that component.
Be aware that this function will not work if the power cord
for the -connected component is connected to the AC
OUTLET on the TX-NR1000/TX-NR5000E, or if the
TX-NR1000/TX-NR5000E has already been turned on.
Direct change function
When the play button is pressed on an
component, the input source selected at the
TX-NR1000/TX-NR5000E automatically changes to
that component.
Power off function
When the TX-NR1000/TX-NR5000E is placed in the
standby state, all -connected components are also
automatically put into the standby state.
Also, if you press the [ON] button on the TX-NR1000/
TX-NR5000E remote controller while the TX-NR1000/
TX-NR5000E is turned on, all
components (DVD players, CD players, MD recorders,
tuners, etc.) are also turned on.
Onkyo DVD player
L
R
ANALOG
OUTPUT
AUDIO IN
R L
4
C DIGITAL IN D DIGITAL IN E MULTI F AUDIO IN G H S VIDEO VIDEO I COMPONENT
- CH VIDEO
OPTICAL COAXIAL IN 1 R L R L IN IN IN 1 IN 2
FR FL
PH 4
1 1 1
SUB C
2 2 5 2
GND
R L
SR SL
1 6
3 3 3
SBR SBL OUT 1 IN 3
4 4 2 7 4
FR FL
5 5 3 8 5
SUB C
6 6 1 9 6
SR SL
1 1 2 4 1 3
SBR SBL
2 2 3 5 2 4
R L R L
OUT OUT OUT OUT
S VIDEO VIDEO VIDEO S VIDEO
MULTI G
- CH
IN 2
C D F H I
SURR R SURR BACK R ( ASSIGNABLE ) FRONT R CENTER FRONT L SURR BACK L ( ASSIGNABLE
( SINGLE )
FRONT R (BTL) FRONT L (BTL)

-compatible AV Components

To connect components using the
connect a remote control cable from this
the
control cable with a 1/8 inch (3.5 mm) miniature two-
conductor plug comes with every cassette tape deck,
compact disc player, MD recorder, and DVD player that
has an
• When performing operations with
• For remote control operation, the audio connection
• If a component has two
• With Onkyo DVD players, you can enter the pre-
-connected
-connected
REMOTE
CONTROL
Remote
control
cable
REMOTE
CONTROL
J K L
ANTENNA RS 232
COMPONENT VIDEO HDMI
IN 4
Y
Y
IN 1
P B
P
B
REMOTE
HDMI, the HDMI logo 12V
P CONTROL
R is a trademark TRIGGER
FM
or registered
75 OUT
trademarks of HDMI
Licensing LLC. A
P R 200mA MAX.
IN 2
Y
B 100mA MAX.
C
OUT 2 100mA MAX.
P
B Y D 100mA MAX.
AM E
100mA MAX.
P R
P
B
MAIN
ZONE 2
P
R
OUT ZONE 3
IN OUT
J K L
IR
) SURR L
SPEAKERS A
AC INLET
AC OUTLET
AC 120V 60Hz
SWITCHED
120W 1A MAX.
SPEAKERS B
UDC / UDT TX-NR 1000
MODEL NO.
Connections for Remote Control (
terminal of the other component. An
terminal.
components using the system, do not use the
remote zone (Zone 2/Zone3).
cables must also be connected.
terminals, you can use
either one to connect to the TX-NR1000/
TX-NR5000E. The other one can be used to daisy
chain with another component.
program code so that you can operate the DVD player
directly with the remote controller without connecting
the terminals (See page 129).
connector
Ex: Onkyo CD player
connector
Ex: Onkyo cassette tape
deck
Remote control cable
)
terminal, simply
terminal to
remote
-connected
TX-NR1000/
TX-NR5000E
REMOTE
CONTROL
47