Table of Contents
Advertisement
Connecting Your Components—Continued
Connecting Onkyo
Step 1: Make sure that each Onkyo component is connected to the AV controller with an analog audio cable (RCA).
Step 2: Make the necessary
Step 3: If you're using an MD, CDR, or RI DOCK component, change the Input Display (see page 49).
With
(Remote Interactive), you can use the following special functions:
Auto Power On/Standby
When you start playback on a component connected via
turn on and select that component as the input source. Similarly, when the AV controller is set to Standby, all compo-
nents connected via
AC OUTLET on the AV controller.
Direct Change
When playback is started on a component connected via
the input source. If your DVD player is connected to the AV controller's multichannel input, you'll need to press the
[AUDIO SEL] button repeatedly and select Multich to hear all channels (see page 78), as the Direct Change
tion selects the DVD IN L/R jacks.
Remote Control
You can use the AV controller's remote controller to control your other
the appropriate remote control code first (see page 117). And remember to point the remote controller at the AV control-
ler and not the other component.
Notes:
• Use only
cables for
are supplied with Onkyo players (DVD, CD, etc.).
• Some components have two
nect either one to the AV controller. The other jack is
for connecting additional
• Connect only Onkyo components to
necting other manufacturer's components may cause
a malfunction.
• Some components may not support all
Refer to the manuals supplied with your other Onkyo
components.
• While Zone 2 or Zone 3 is on, the Auto Power
On/Standby and Direct Change
work.
Connecting the Power Cord
• Before connecting the power cord, connect all your speakers and AV components.
• Connect the power cord to the AV controller's AC INLET.
• Plug the other end of the power cord into a suitable wall outlet.
• Turning on the AV controller may cause a momentary power surge that might interfere with other electrical equipment
on the same circuit. If this is a problem, plug the AV controller into a different branch circuit.
42
Components
connections (see illustration below).
will also go on Standby. This function will not work with components that are connected to an
connections.
cables
jacks. You can con-
-capable components.
jacks. Con-
functions.
functions do not
, if the AV controller is on Standby, it will automatically
, the AV controller automatically selects that component as
-capable Onkyo components. You must enter
IN 4
IN 3
RS232
COMPONENT VIDEO
MONITOR OUT 2
ASSIGNABLE
/ZONE 2 OUT
SIRIUS
MONITOR
IN 3
IN 2
IN 1(DVD)
OUT 1
Y
AUX 1
V
C
/P
REMOTE
B
B
CONTROL
DIGITAL
ASSIGNABLE
COAXIAL
IN 1
(DVD)
C
/P
R
R
S
IN
IN
OUT
IN
IN 2
(VCR/DVR)
L
L
IN 3
(CBL/SAT)
R
R
OPTICAL
PHONO
CD
TAPE
AUX 1
REMOTE
IN 1
(GAME/TV)
GND
BALANCE L
SURR BACK R
BALANCE R
MONO
Bi-AMP
CONTROL
IN 2
(CD)
2
1
3
OUT
HOT
GND
COLD
INPUT
e.g., CD player
e.g., DVD player
IN
L
R
HDMI
ASSIGNABLE
CD
IN 2
IN 1
OUT
OUT
MAIN
SUB
XM
ETHERNET
MONITOR
GAME/TV CBL/SAT
VCR/DVR
DVD
OUT
IR
V
A
B
C
ZONE 2
IN
OUT
12V TRIGGER OUT
ZONE 2
ZONE 3
FRONT
SW
S
OUT
A
B
IN
IN
IN
OUT
IN
IN
FRONT
CENTER
SURR
SURR BACK
FRONT
CENTER
SURR
SURR BACK
L
L
R
SUBWOOFER
SUBWOOFER
GAME/TV
CBL/SAT
VCR/DVR
DVD
MULTI CH
PRE OUT
PRE OUT
SURR R
FRONT R
CENTER
FRONT L
SURR L
R
DVD
R
L
ANALOG
AUDIO OUT
R
L
ANALOG
AUDIO OUT
func-
AC INLET
Hide quick links:
Advertisement
Table of Contents
