Table of Contents
Advertisement
Zone 2 and Zone 3—Continued
Using the 12V Triggers
The 12V triggers A, B, and C can be used to turn on 12V
trigger-capable components automatically when they are
selected as the input source. The triggers can be set so
that they activate when a connected component is
selected as the input source for the main room, Zone 2,
Zone 3, or any combination of rooms.
When triggered, the output from a 12V TRIGGER OUT
goes high (+12 volts, 100 milliamperes max).
IN 4
IN 3
RS232
COMPONENT VIDEO
MONITOR OUT 2
ASSIGNABLE
/ZONE 2 OUT
MONITOR
IN 3
IN 2
IN 1(DVD)
OUT 1
Y
REMOTE
C
B
/P
B
CONTROL
DIGITAL
ASSIGNABLE
COAXIAL
IN 1
(DVD)
C
R
/P
R
IN
IN
OUT
IN
IN 2
(VCR/DVR)
L
L
IN 3
(CBL/SAT)
R
R
OPTICAL
PHONO
CD
TAPE
IN 1
(GAME/TV)
GND
BALANCE L
SURR BACK R
BALANCE R
MONO
IN 2
(CD)
2
1
3
OUT
HOT
GND
COLD
INPUT
Hookup
• Use a miniplug cable to connect the AV controller's
12V TRIGGER OUT A, B, or C jack to the 12 V trig-
ger input on a connected component.
When several components are turned on simultaneously
by using triggers A, B, and C, depending on the type of
components, a large amount of current may be drawn
momentarily. To prevent this, you can delay trigger sig-
nals A, B, and C individually. Another application for
trigger delay is eliminating the "thump" noise that's
sometimes heard when a source component is turned on.
Delaying the trigger signal for your power amplifier so
that it's the last component to be turned on will accom-
plish this.
1
Press the [RECEIVER] REMOTE
MODE button, followed by the
RECEIVER
[SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [
buttons to select
"6. Miscellaneous," and then
press [ENTER].
ENTER
The Miscellaneous menu appears.
ENTER
114
C
12V TRIGGER OUT
A
B
HDMI
AC INLET
ASSIGNABLE
IN 2
IN 1
OUT
OUT
MAIN
SUB
HD RADIO
XM
ANTENNA
ETHERNET
AM
FM75
SIRIUS
AM
MONITOR
AUX 1
GAME/TV CBL/SAT
VCR/DVR
DVD
OUT
IR
ANTENNA
V
V
A
B
C
AC OUTLET
ZONE 2
IN
FM
OUT
75
12V TRIGGER OUT
ZONE 2
ZONE 3
SW
S
S
OUT
A
B
IN
IN
IN
OUT
IN
IN
FRONT
CENTER
SURR
SURR BACK
FRONT
CENTER
SURR
SURR BACK
L
AC 120V
60Hz
SWITCHED
120W 1A MAX.
R
SUBWOOFER
SUBWOOFER
AUX 1
GAME/TV
CBL/SAT
VCR/DVR
DVD
MULTI CH
PRE OUT
PRE OUT
SURR BACK L
SURR R
FRONT R
CENTER
FRONT L
SURR L
SUBWOOFER
Bi-AMP
Bi-AMP
1
2
3
GND
HOT
COLD
PRE OUT
6.Miscellaneous
1.Volume Setup
2.OSD Setup
3.12V Trigger
A
Setup
4.12V Trigger
B
Setup
5.12V Trigger
C
Setup
3
ENTER
ENTER
4
ENTER
ENTER
5
ENTER
ENTER
]/[
]
6
Use the Up and Down [
buttons to select "12V Trigger A,
B, or C," and then press [ENTER].
The 12V Trigger A/B/C Setup screen
appears.
6-x.12V Trigger x Setup
Delay
DVD
VCR/DVR
CBL/SAT
TV/GAME
AUX1
AUX2
TAPE
TUNER
CD
PHONO
Use the Up and Down [
buttons to select "Delay," and use
the Left and Right [
tons to select: 0 sec, 1 sec, 2 sec,
or 3 sec.
When 0 sec is selected, the trigger sig-
nal is output as soon as the input source
is changed.
Use the Up and Down [
buttons to select an input source,
and use the Left and Right
[
]/[
] buttons to select an
option.
Off: No trigger signal is output.
A 12-volt trigger signal is output when
the connected component is selected as
the source for:
Main: Main room.
Zone2: Zone 2.
Main/Z2: Main room or Zone 2.
Zone3: Zone 3.
Main/Z3:Main room or Zone 3.
Z2/Z3: Zone 2 or Zone 3.
Main/Z2/Z3:Main room, Zone 2, or
Zone 3.
When you've finished, press the
[SETUP] button.
Setup closes.
]/[
]
1sec
Main/Zone2
Main/Zone2
Main/Zone2
Main/Zone2
Main/Zone2
Main/Zone2
Main/Zone2
Main/Zone2
Main/Zone2
Main/Zone2
]/[
]
]/[
] but-
]/[
]
Hide quick links:
Advertisement
Table of Contents
