Toshiba E-STUDIO287CS User Manual page 14

PRINTING FROM WINDOWS
 [Basic] tab
The [Basic] tab contains basic print operation settings, such as
the original paper size, print paper size, paper source, paper
1
type, destination, number of copies, orientation, and so on.
2
3
1) Original Paper Size
This selects the size of a document to be printed.
4
Available original paper sizes are listed below:
• A4 (210 x 297 mm)
• A5 (148 x 210 mm)
• B5 (182 x 257
• Folio (210 x 330 mm)
• A6 (105 x 148mm)
• Postcard
5
• Letter (8 1/2 x 11")
• Legal (8 1/2 x 14")
• Statement
(5 1/2 x 8 1/2")
• 13"LG (8 1/2 x 13")
• 8.5"SQ (8 1/2 x 8 1/2")
• 16K (195 x 270 mm)
• 13.5"LG (8 1/2 x 13.5")
• IndexCard (3 x 5")
6
Note
• There are also 40 custom paper sizes in the [Original
Paper Size] box. You can set the custom paper sizes in
the [Others] tab.

P.27 "[Others] tab"
7
• The default paper size will be [Letter] or [A4] according
to the regional setting in the Windows.
2) Print Paper Size
Select this to enlarge or reduce a page image to fit exactly
in the selected paper size. If you do not wish to enable
enlarge or reduce printing, select [Same as Original Size].
Note
• When you use the custom paper size, you need to select
manually the custom paper size in a drawer in advance.
1
2
3
4
5
6
7
8
9
• Executive
(7 1/4 x 10 1/2")
• Env-Com10
(4 1/8 x 9 1/2")
• Env-Com9
(3 7/8 x 8 7/8")
• Env-Monarch
(3 7/8 x 7 1/2")
• Envelope DL
(110 x 220 mm)
• Envelope Cho-3
(120 x 235 mm)
• Envelope You-4
(105 x 235 mm)
• Envelope-C5
(162 x 229mm)
- 14 -
Memo
• There are also 20 custom paper sizes in the [Print Paper
Size] box. You can set the custom paper sizes in the
[Others] tab.
3) Image Scale
Select this check box to enter the scale manually to enlarge
or reduce an image. The ratio can be set at between 25
and 400%.
Memo
• For detailed instructions on how to print with the [Image
Scale] setting, see the following page:

P.43 "Fitting images within paper size"
4) Paper Source
This selects a paper source to print a job in the most
suitable paper size. The figure on the right indicates the
paper size set for each paper source. When you select a
paper source, the chosen one is indicated with a green
square in the figure.
Memo
• Youj can select a paper source by directly clicking on the
figure on the right.
- Auto — Automatically selects the paper set in this
equipment according to the printed document size.
- Drawer 1 — Paper is fed from the 1st Drawer.
- Drawer 2 — Paper is fed from the 2nd Drawer.
- Drawer 3 — Paper is fed from the 3rd Drawer.
- Drawer 4 — Paper is fed from the 4th Drawer.
- Bypass Tray — Paper is fed from the bypass tray.
When this is selected and print a job, [JOB STATUS] on
the touch panel will blink. Press [JOB STATUS] and
check the paper size of the job. Then set the paper and
press the [START] button to print a job.
Note
• The selectable values vary depending on the optional
devices installed in this equipment and their
configuration on the [Device Settings] tab.
• When paper such as special that needs to be fed from
the bypass tray is set, [Bypass Tray] may be
automatically selected in the [Paper Source] box, and
then a confirmation dialog box may appear.
• When the paper size settings on the [Device Settings]
tab differ from those in the equipment, the paper source
setting is ignored and the equipment may prompt to set
the paper in the bypass tray.
• The Large Capacity Feeder is not available for some
countries or regions.
5) Paper Type
This sets the media type of the paper.
- Plain (Thin) — Select this when printing on plain thin
paper.
- Plain — Select this when printing on plain paper.
- Thick1 — Select this when printing on thick 1 paper.
- Thick2 — Select this when printing on thick 2 paper.
- Thick3 — Select this when printing on thick 3 paper.
- Thick4 — Select this when printing on thick 4 paper.
- Thick5 — Select this when printing on thick 5 paper.