Mitsubishi Electric FR-F500 Series Instruction Manual page 27

( 3 ) Cables, crimping terminals, etc.
The following table lists the cables and crimping terminals used with the inputs (R, S, T) 〈L
outputs (U, V, W) of the inverter and the torques for tightening the screws:
• • • • FR-F520-0.75K to 55K
Terminal
Applicable Inverter
Screw
Type
Size
FR-F520-0.75K to 2.2K M4
FR-F520-3.7K M4
FR-F520-5.5K M5
FR-F520-7.5K M5
FR-F520-11K M5
FR-F520-15K M6
FR-F520-18.5K M6
FR-F520-22K M8
FR-F520-30K M8
FR-F520-37K M10
FR-F520-45K M10
FR-F520-55K M12
• • • • FR-F540-0.75K to 55K
Terminal
Applicable Inverter
Screw
Type
Size
FR-F540-0.75K to 3.7K M4
FR-F540-5.5K M4
FR-F540-7.5K M4
FR-F540-11K M4
FR-F540-15K M6
FR-F540-18.5K M6
FR-F540-22K M6
FR-F540-30K M6
FR-F540-37K M6
FR-F540-45K M8
FR-F540-55K M8
Note: 1. The cables used should be 75°C (167°F) copper cables.
2. Tighten the terminal screws to the specified torques.
Undertightening can cause a short or misoperation.
Overtightening can cause the screws and unit to be damaged, resulting in a short or
misoperation.
( 4 ) Connection of the power supply and motor
No-fuse
breaker
The power supply cables
must be connected to R, S, T
〈L
If they are connected to U, V,
W, the inverter will be damaged.
Phase sequence need not be
matched.
For use with a single-phase
power supply,the power supply
cables must be connected to
R and S 〈L
Crimping Terminals
Tightening
Torque
N ⋅ ⋅ ⋅ ⋅ m
R, S, T
U, V, W
〈 〈 〈 〈 L 〉 〉 〉 〉
, L , L
1 2 3
1.5 2-4
1.5 5.5-4
2.5 5.5-5
2.5 14-5
2.5 14-5
4.4 22-6
4.4 38-6
7.8 38-8
7.8 60-8
14.7 80-10
14.7 100-10 100-10
24.5 150-12 150-12
Crimping Terminals
Tightening
Torque
N ⋅ ⋅ ⋅ ⋅ m
R, S, T
U, V, W
〈 〈 〈 〈 L 〉 〉 〉 〉
, L , L
1 2 3
2-4 〈2.5-4〉 2-4 〈2.5-4〉
1.5
5.5-4 〈4-4〉 2-4 〈2.5-4〉
1.5
5.5-4 〈4-4〉 5.5-4 〈4-4〉
1.5
5.5-4 〈4-4〉 5.5-4 〈4-4〉
1.5
14-6 〈16-6〉 8-6 〈10-6〉
4.4
14-6 〈16-6〉 8-6 〈10-6〉
4.4
22-6 〈25-6〉 14-6 〈16-6〉
4.4
22-6 〈25-6〉 22-6 〈25-6〉
4.4
22-6 〈25-6〉 22-6 〈25-6〉
4.4
38-8 〈50-8〉 38-8 〈35-8〉
7.8
60-8 〈50-8〉 60-8 〈50-8〉
7.8
R S T
Power 〈L 〉 〈L 〉 〈L
1 2
supply
R S
〈L 〉 〈L 〉
1 2
〉.
, L , L
1 2 3
〉.
and L
1 2
INSTALLATION AND WIRING
HIV Cables (Note 1)
mm 2
R, S, T
U, V, W
〈 〈 〈 〈 L 〉 〉 〉 〉
, L , L
1 2 3
2-4 2 2
5.5-4 3.5 3.5
5.5-5 5.5 5.5
8-5 14 8
14-5 14 14
22-6 22 22
38-6 38 38
38-8 38 38
60-8 60 60
80-10 80 80
100 100
150 150
HIV Cables (Note 1)
mm 2
R, S, T
U, V, W
〈 〈 〈 〈 L 〉 〉 〉 〉
, L , L
1 2 3
2 2
3.5 2
3.5 3.5
5.5 5.5
14 8
14 8
22 14
22 22
22 22
38 38
60 60
Earth (Ground)
U V W
〉
terminal
3
Earth (Ground)
T U V W
〈L 〉
3
Connect the motor to U, V, W.
In the above connection,
turning on the forward rotation
switch (signal) rotates the motor
in the counterclockwise (arrow)
direction when viewed from
the load shaft.
16
, L , L
1 2
IEC Cables
(Note 1)
AWG mm
R, S, T R, S, T
U, V, W
〈 〈 〈 〈 L 〉 〉 〉 〉 〈 〈 〈 〈 L
, L , L , L , L
1 2 3 1 2
14 14 2.5
12 12 4
10 10 6
6 8 16
6 6 16
4 4 35
2 2 35
2 2 35
1/0 1/0 50
3/0 3/0 70

4/0 4/0

MCM300 MCM300
IEC Cables
(Note 1)
AWG mm
R, S, T R, S, T
U, V, W
〈 〈 〈 〈 L 〉 〉 〉 〉 〈 〈 〈 〈 L
, L , L , L , L
1 2 3 1 2
14 14 2.5
12 14 4
12 12 4
10 10 6
6 8 16
6 8 16
4 6 25
4 4 25
4 4 25
2 2 50
1/0 1/0 50
Motor
〉 and
3
2
U, V,
〉 〉 〉 〉
W
3
2.5
2.5
4
6
10
16
25
35
50
70


2
U, V,
〉 〉 〉 〉
W
3
2.5
2.5
4
2 2
6
10
10
16
25
25
35
50