Mode Check Display - Panasonic AJ-PX800G Operating Instructions Manual

No Item
16 Y GET brightness display
17 ND filter display
18 Shutter speed display
19 <WHITE BAL> switch position display
20 Gain display
21 Iris display
22 Zoom position display
23 Focus control information display
24 Recommended ND filter display
25 Camera warning, notification display area
26 Automatic white balance abnormal display
27 Automatic black balance abnormal display
Chromatic aberration compensation
28
function display
29 Lens extender display
30 Flash band compensation function display
31 Dynamic range stretcher function display
32 Scene file name display
33 Battery charge level indicator
34 P2 card remaining free space
35 Simultaneous recording mode display
36 High-sensitivity mode display
37 One clip recording mode status display
Recording/playback operation status
38
display
39 Rec during upload status display
40 Streaming distribution status display
HD SDI REMOTE recording status and
41
4G/LTE connection status display
*1 May be displayed depending on other settings.
*2 Displayed when the remaining capacity becomes smaller.
*3 Displayed during shooting.
*4 Always displayed when [HD SDI REMOTE] is set or when 4G/LTE connection is set.

Mode check display

The camera settings and status can be displayed on the viewfinder.
Each time the <DISP/MODE CHK> switch on the camera is pushed towards the <CHK> side, the five screens are switched.
[STATUS] screen display → [FUNCTION] screen display → [AUDIO] screen display → [USER SW] screen display → [CAC INFO] screen display → no
display
Each screen is displayed for approximately five seconds. Pushing the <DISP/MODE CHK> switch towards the <CHK> side while the screen is displayed
moves to the next screen.
[FUNCTION] screen
Displays the video output status and information of the recording media.
[SDI OUT]
[P2CARD STATUS]
Chapter 8 Display — Screen status display
Shooting Playback
—
l
—
l
—
l
—
l
—
l
—
l
—
l
—
l
—
l
l l
—
l
—
l
—
l
—
l
—
l
—
l
—
l
l l
l l
—
l
—
l
—
l
l l
l l
l l
—
l
*4
— Displays the status of the signal output from the <SDI OUT/IN (OP)> terminal.
Displays the format of the signal output from the <SDI OUT/IN (OP)> terminal by [HD-SDI]/
[TYPE]
[SD-SDI].
Displays the superimposition status of characters selected in the main menu → [IN/OUT
[CHAR]
SEL] → [SDI OUT CHAR] by [ON]/[OFF].
Displays the status of the P2 card inserted in the card slot, remaining capacity, and total
used capacity.
The statuses of cards to be displayed are as follows:
—
[ACTIVE]/[ACCESSING]/[INFO READING]/[FULL]/[PROTECTED]/[NOT SUPPORTED]/
[FORMAT ERROR]/[AUTH NG]/[REC IMPOSSIBLE]/[NO CARD]
For details, refer to "P2 card access LEDs and status of P2 cards" (page 43).
[TOTAL P2/mP2] Displays the remaining capacity/total capacity of slots 1 and 2 altogether.
[SLOT1] Displays the status of the P2 card in slot 1 and remaining capacity/total capacity.
[SLOT2] Displays the status of the P2 card in slot 2 and remaining capacity/total capacity.
– 159 –
<DISP/
<DISP/MODE
MODE CHK>:
CHK>: <OFF>
<CHK>
—
l
—
l
—
l
—
l
—
l
—
l
—
l
—
l
—
l
l l
—
l
—
l
—
l
—
l
—
l
—
l
—
l
—*
l 2
—*
l 2
—
l
—
l
—
l
—*
l
3
— —
— —
—
l
*4
<DISP/MODE CHK>: <ON>
[OTHER DISPLAY]
[ALL] [PARTIAL] [USER]
l l
—
l
l l
l l
l l
l l
—* —*
1 1
—* —*
1 1
—* —*
1 1
—* —*
1 1
— —
— —
l l
l l
l l
l l
—
l
—* —*
1 1
—* —*
1 1
—
l
l l
l l
l l
—* —*
1 1
—* —*
1 1
l l
*4 *4
l
l
l
l
l
l
—*
1
—*
1
—*
1
—*
1
—
—
l
l
l
l
l
—*
1
—*
1
l
l
l
l
—*
1
—*
1
l
*4