Panasonic AJ-PX800G Operating Instructions Manual page 157

24 Recommended ND filter display
Displays the ND filter recommended for the current shooting conditions.
25 Camera warning, notification display area (pages 203, 158)
26 Automatic white balance abnormal display
Displayed when the automatic white balance is abnormal during mode check.
27 Automatic black balance abnormal display
Displayed when the automatic black balance is abnormal during mode check.
28 Chromatic aberration compensation function display
Displayed when the chromatic aberration compensation function is active.
29 Lens extender display
Displayed when the lens extender is used.
30 Flash band compensation function display
Displayed when the flash band compensation function is activated.
31 Dynamic range stretcher function display
Displayed when the dynamic range stretcher function is working.
32 Scene file name display
Indicates the scene file name [F1:] to [F6:].
33 Battery charge level indicator
f [**.*V]: Displays the battery charge level in 0.1 V unit.
f [***%]: Displays the charge level of batteries with charge level information in %.
f [EMP]: Displayed when there is no charge level on batteries with charge level information or the level is at the near end setting value or below.
f [MAX]: Displayed when batteries with charge level information are fully charged.
34 P2 card remaining free space
: This is the slot No. This is displayed in black and white inversion when the slot No. is recording destination. It flashes while the card is being
f
recognized.
f [***min]: Displays the remaining space on the media in each slot. During a near end, it flashes. 0 to 599 indicates minutes, while 600 minutes or
longer indicates hours.
f No display: Not displayed when a card is not inserted.
f [END]: Displayed when there is no space remaining on each card.
f [WP]: Displayed when the P2 card is write-protected.
f [ERR]: Displayed in case of format errors or authentication errors.
f [LOOP ***min]: Displayed when the loop recording mode is set. [LOOP] flashes when loop recording is not possible, for example, when there is
no more space remaining on the P2 card. During the mode check, the second line displays the standard recording time of loop recording.
35 Simultaneous recording mode display
f [SIMUL]: Displayed when the simultaneous recording is set. When the simultaneous recording cannot be performed, [SIMUL] indication is
displayed with a diagonal line.
36 High-sensitivity mode display
Displayed when [HIGH SENS.] is set in the main menu → [SYSTEM MODE] → [SHOOTING MODE].
37 One clip recording mode status display
f [1-CLIP]: The status where a new clip is to be recorded in one-clip recording
f [1*CLIP]: The status where recording can be performed by combining to the previous clip in one-clip recording
38 Recording/playback operation status display
f [REC]* : Recording
1
f No display: Recording standby
f [&]: Playback pause
f [=]: Playback
f [&=] ([~&]): Frame-by-frame playback (frame-by-frame rewind)
f [)] ([%]): Fast-forwarding/fast-forward playback (fast-reversing/fast-reverse playback)
f [CLIP&=] ([CLIP~&]): Clip forwarding (clip rewinding), cueing up by clips
f [CLIP&T&=] ([CLIP&T~&]): Cueing up (rewinding) by clip and text memo (when [CLIP&TEXT MEMO] is set in the main menu → [OTHER
FUNCTIONS] → [SEEK POS SEL])
f [START]* : Displayed when recording of a new clip is started in one-clip recording.
1
f [END]* : Displayed when combining of clips is ended in one-clip recording.
1
f [L-]* : Loop recording
2
f [I-]* : Interval recording, one-shot recording
2
f [P-]* : Pre-recording
2
*1 Even if the display is set to [OFF], only [REC], [START], and [END] are displayed. Also, when pre-recording, loop recording, interval recording, or one-shot
recording is set, it is displayed.
*2 Displayed when [INTERVAL], [ONE SHOT], or [LOOP] is set in the main menu → [RECORDING SETUP] → [RECORDING], or when [ON] is set in the
main menu → [RECORDING SETUP] → [PRE REC].
39 Rec during upload status display
Displays the status of rec during upload.
f [ ]: Displayed when the rec during upload function is enabled.
The display will blink when recording is started immediately after the power is turned on or the P2 card is inserted, and the upload will not be
performed until the recording is stopped.
f [ ]: Displayed during upload.
Chapter 8 Display — Screen status display
– 157 –