Panasonic AJ-PX800G Operating Instructions Manual page 129

Item
[FILE SPLIT]
[RECORDING [RECORDING HOLD]
SETTING]
[ONE SHOT TIME]
[INTERVAL TIME]
[START DELAY]
[PRE REC]
[ONE CLIP REC]
[SIMUL REC]
[DUAL CODEC [CODEC USAGE]
SETTING]
[PROXY REC MODE]
[STREAMING MODE]
[PROXY DISP]
[QoS MAX RATE]
[QoS MIN RATE]
[STREAMING
LATENCY]
Chapter 6 Menu Operations — Menu list
Selects the split method of the recording file.
[NORMAL]: Divides the file every 4 GB regardless of the recording format.
[SHORT]: Divides the file every 128 seconds regardless of the recording format.
f Factory setting: [NORMAL]
If the clip is recorded in one file, it cannot be copied to a P2 memory card or 32 GB microP2 memory card,
or copied or exported to a storage.
A clip will be divided to recording files of approximately 128 seconds when [SHORT] is selected, but they
can be operated as a single clip when the thumbnails of clips are operated on the P2 device. A single
continuous recording time is approximately 3.5 hours. [SHORT] is disabled in interval recording, one-shot
recording, and loop recording modes.
Selects whether to hold [RECORDING] settings.
[ON]: Holds the settings.
[OFF]: Does not hold the settings. It will always be [NORMAL] the next time when the power is turned on.
f Factory setting: [OFF]
Sets the recording duration of one-shot recording.
[1frm], [2frm], [4frm], [8frm], [16frm], [1s]
f Factory setting: [1frm]
Sets the interval duration for interval recording.
[2frm], [4frm], [8frm], [16frm], [1s], [2s], [5s], [10s], [30s], [1min], [5min], [10min]
f Factory setting: [2frm]
Selects whether to delay the recording start time by approximately one second when performing interval
recording or one-short recording.
[ON], [OFF]
f Factory setting: [OFF]
Selects whether to perform pre-recording. If [ON] is selected, pre-recording is performed for approximately
three seconds in HD, and for approximately seven seconds in SD.
[ON], [OFF]
f Factory setting: [OFF]
Selects whether to perform one-clip recording.
[ON], [OFF]
f Factory setting: [OFF]
Selects whether to perform simultaneous recording.
[ON], [OFF]
f Factory setting: [OFF]
Selects media for recording proxy data.
[PROXY REC(P2)]: Records proxy data to a P2 card.
[PROXY REC(P2&SD)]: Records proxy data to both of a P2 card and SD memory card.
[STREAMING]: Outputs video stream.
[OFF]: Does not record proxy data or output streaming.
f Factory setting: [OFF]
If [CODEC USAGE] cannot be changed, change the [PROXY REC MODE] or [STREAMING MODE]
setting.
Sets the recording mode of proxy data.
[LOW 2CH MOV], [HQ 2CH MOV], [SHQ 2CH MOV], [AVC-G6 2CH MOV]
f Factory setting: [HQ 2CH MOV]
Sets the transfer mode for streaming.
[LOW], [HQ], [AVC-G6], [SHQ (QoS)], [AVC-G (QoS)]
f Factory setting: [HQ]
Selects whether to display proxy data recorded information or messages in the viewfinder.
[ON]: Displays proxy recording information and SD memory card remaining capacity at the start of
recording. Warning information is displayed at all times.
[OFF]: Displays proxy and SD memory card warning information for only three seconds when warning
occurs.
f Factory setting: [OFF]
Sets the maximum bitrate for video data when the QoS is operating. This setting is used when the
streaming distribution is started from the operation of the camera.
This can be set when [CAMERA] is selected in the main menu → [NETWORK SETUP] → [STREAMING
SETTING] → [START TRIGGER].
[256Kbps], [512Kbps], [1Mbps], [1.5Mbps], [2.5Mbps], [3.5Mbps], [6Mbps], [9Mbps]
f Factory setting: [9Mbps]
[9Mbps] cannot be selected when [STREAMING MODE] is set to [SHQ (QoS)].
Sets the minimum bitrate for video data when the QoS is operating. This setting is used when the
streaming distribution is started from the operation of the camera.
This can be set when [CAMERA] is selected in the main menu → [NETWORK SETUP] → [STREAMING
SETTING] → [START TRIGGER].
[256Kbps], [512Kbps], [1Mbps], [1.5Mbps], [2.5Mbps], [3.5Mbps], [6Mbps], [9Mbps]
f Factory setting: [256Kbps]
Sets the delay mode during the streaming distribution. This setting is used when the streaming distribution
is started from the operation of the camera.
This can be set when [CAMERA] is selected in the main menu → [NETWORK SETUP] → [STREAMING
SETTING] → [START TRIGGER].
[NORMAL]: Set this to prioritize the stability of streaming.
[SHORT]: Set this to prioritize the reduction of streaming delay.
f Factory setting: [NORMAL]
– 129 –
Description of settings