Panasonic AJ-PX800G Operating Instructions Manual page 133

Item
[WIRELESS TYPE]
[RECORDING CH [FRONT VR CH1]
SETTING]
[FRONT VR CH2]
[FRONT VR CH3]
[FRONT VR CH4]
[MIC LOWCUT CH1]
[MIC LOWCUT CH2]
[MIC LOWCUT CH3]
[MIC LOWCUT CH4]
[LIMITER CH1]
[LIMITER CH2]
[LIMITER CH3]
[LIMITER CH4]
[HEADROOM]
[OUTPUT SETTING] [TEST TONE]
Chapter 6 Menu Operations — Menu list
Selects the type of wireless microphone receiver.
[SINGLE]: Selects a single channel type wireless microphone receiver.
[DUAL]: Selects a double channel type wireless microphone receiver.
f Factory setting: [SINGLE]
Selects whether to enable the <F.AUDIO LEVEL> dial for input signals selected for audio channel 1.
[FRONT]: Enabled only when [FRONT] is selected.
[W.L.]: Enabled only when wireless microphone receiver is selected.
[REAR]: Enabled only when [REAR] is selected.
[ALL]: Enabled when any input is selected.
[OFF]: Disabled regardless of the input selected. Recording levels do not change even if the volume dial
is turned.
f Factory setting: [OFF]
Selects whether to enable the <F.AUDIO LEVEL> dial for input signals selected for audio channel 2.
[FRONT]: Enabled only when [FRONT] is selected.
[W.L.]: Enabled only when wireless microphone receiver is selected.
[REAR]: Enabled only when [REAR] is selected.
[ALL]: Enabled when any input is selected.
[OFF]: Disabled regardless of the input selected. Recording levels do not change even if the volume dial
is turned.
f Factory setting: [OFF]
Selects whether to enable the <F.AUDIO LEVEL> dial for input signals selected for audio channel 3.
[FRONT]: Enabled only when [FRONT] is selected.
[W.L.]: Enabled only when wireless microphone receiver is selected.
[REAR]: Enabled only when [REAR] is selected.
[ALL]: Enabled when any input is selected.
[OFF]: Disabled regardless of the input selected. Recording levels do not change even if the volume dial
is turned.
f Factory setting: [OFF]
Selects whether to enable the <F.AUDIO LEVEL> dial for input signals selected for audio channel 4.
[FRONT]: Enabled only when [FRONT] is selected.
[W.L.]: Enabled only when wireless microphone receiver is selected.
[REAR]: Enabled only when [REAR] is selected.
[ALL]: Enabled when any input is selected.
[OFF]: Disabled regardless of the input selected. Recording levels do not change even if the volume dial
is turned.
f Factory setting: [OFF]
Enables/disables the lowcut filter for audio channel 1.
[ON], [OFF]
f Factory setting: [OFF]
Enables/disables the lowcut filter for audio channel 2.
[ON], [OFF]
f Factory setting: [OFF]
Enables/disables the lowcut filter for audio channel 3.
[ON], [OFF]
f Factory setting: [OFF]
Enables/disables the lowcut filter for audio channel 4.
[ON], [OFF]
f Factory setting: [OFF]
Enables/disables the limiter for audio channel 1.
[ON], [OFF]
f Factory setting: [OFF]
Enables/disables the limiter for audio channel 2.
[ON], [OFF]
f Factory setting: [OFF]
Enables/disables the limiter for audio channel 3.
[ON], [OFF]
f Factory setting: [OFF]
Enables/disables the limiter for audio channel 4.
[ON], [OFF]
f Factory setting: [OFF]
Sets the headroom (standard level).
[18dB], [20dB]
f Factory setting: [20dB]
Outputs rated level 1 kHz tone signal according to the reference level.
The standard level varies depending on the setting of [HEADROOM].
[NORMAL]: Outputs the test tone to CH1/CH2/CH3/CH4 when the <OUTPUT>/<AUTO KNEE>
selector switch is switched to <BARS> and audio channel 1 is set to [FRONT] at the [IN] item on the
[AUD02:INPUT] screen of SmartUI.
[ALWAYS]: Always outputs the test tone to CH1/CH2/CH3/CH4 when the <OUTPUT>/<AUTO KNEE>
selector switch is switched to <BARS>.
[CHSEL]: Outputs the test tone to the channel where the [IN] item on the [AUD02:INPUT] screen of
SmartUI is set to [FRONT] when the <OUTPUT>/<AUTO KNEE> selector switch is switched to <BARS>.
(Does not output to CH3/CH4.)
[OFF]: Does not output the test tone.
f Factory setting: [NORMAL]
– 133 –
Description of settings