Starting The Engine; Adding Bar And Chain Lubricant - Homelite HCS3435A User Manual

GB
F D E I P
Loosen the fuel cap slowly.
■
Carefully pour the fuel mixture into the tank. Avoid
■
spillage.
Prior to replacing the fuel cap, clean and inspect the
■
gasket.
Immediately replace the fuel cap and hands tighten it.
■
Wipe up any fuel spillage.
Note: It is normal for the engine to emit smoke during
and after the first use.
(ADD IMAGE PUMP + LUBRICANT = MIX FROM OTHER
PETROL MANUALS)
1 litre + 20 ml
2 litres + 40 ml
3 litres + 60 ml
4 litres + 80 ml
5 litres + 100 ml

ADDING BAR AND CHAIN LUBRICANT

See Figure 6.
Use HOMELITE Bar and Chain Lubricant. It is designed for
chains and chain oilers, and is formulated to perform over
a wide temperature range with no dilution required. The
chainsaw should use approximately one tank of lubricant
per tank of fuel.
Note: Do not use dirty, used, or otherwise contaminated
lubricants. Damage may occur to the lubricant pump, bar,
or chain.
Carefully pour the bar and chain lubricant into the
■
lubricant tank.
Fill the lubricant tank every time you fuel the engine.
■
OPERATING THE CHAIN BRAKE
See Figures 7 - 8.
Check the operating condition of the chain brake prior to
OPERATION
each use.
Engage the chain brake by rotating your left hand
■
around the front handle, allowing the back of your
hand to push the chain brake lever/hand guard toward
the bar while the chain is rotating rapidly. Be sure to
maintain both hands on the saw handles at all times.
Reset the chain brake back into the RUN position by
■
HCS3435A-25lgs manual.indd Sec1:37 HCS3435A-25lgs manual.indd Sec1:37
NL S DK N FIN GR HU
English

STARTING THE ENGINE

See Figures 8 - 13.
Starting the product differs depending on whether the
engine is cold or warm.
=
}
=
■
= 50: 1
=
=
■
To start a cold engine:
■
■
■
■
■
■
■
37
CZ RU RO PL SLO HR TR EST LT
grasping the top of the chain brake lever/hand guard
and pulling toward the front handle until you hear a
click.
WARNING:
If the chain brake does not stop the chain
immediately, or if the chain brake will not stay
in the run position without assistance, take the
saw to an authorised service centre for repair
prior to use.
WARNING:
Keep your body to the left of the chain line. Never
straddle the saw or chain, or lean over past the
chain line.
Place the chainsaw on level ground and ensure
that no objects or obstructions are in the immediate
vicinity that could come in contact with the bar and
chain.
Hold the front handle firmly with your left hand and
put your right foot onto the base of the rear handle.
Set the ignition switch to the RUN ( I ) position.
Make sure the chain brake is in the run position by
pulling back on the lever/hand guard.
Fully press and release the primer bulb at least 7
times.
Pull choke lever all the way out to FULL position.
When the temperature is above 10°C, pull the starter
grip until the engine attempts to start, but no more
than 3 times. When the temperature is below 10°C,
pull the starter grip until the engine attempts to start,
but no more than 5 times.
Push choke lever to RUN position. Pull starter grip
until engine runs.
Note: Allow the saw to run in this position 15-30
seconds, depending upon the temperature.
Depress the trigger release and squeeze and release
the throttle trigger to return the engine to idle after a
total run time of at least 30 seconds.
CAUTION:
Failure to release partial throttle when chain
brake lever is in the brake position will result in
serious damage to the unit. Never squeeze and
hold the throttle trigger while the chain brake is in
the brake position.
LV SK BG
12/19/08 3:08:52 PM 12/19/08 3:08:52 PM