Table of Contents
Advertisement
CC484/CC486/CC488 | Operators Manual | 10.
4
Sensor Watch Fault
A sensor watch fault registers because one
or more detection devices failed to detect
any movement during the disarmed state
for the time period programmed by your
installer. The fault clears once the zone in
question detects movement and resets.
Press and hold the [4] key until two beeps
sound. This displays the zone reporting
the sensor watch fault.
5
RF Sensor Watch
An RF sensor watch fault registers
because one or more RF detection
devices fails to communicate to the RF
radio receiver for the time period
programmed by your installer. The fault
clears once the RF device in question
successfully transmits to the RF radio
receiver.
Press and hold the [5] key until two beeps
sound. This displays the RF detection
device reporting the RF sensor watch
fault.
6
Communication Fail
A communication fail registers when the
control panel fails to communicate with
the receiving party (such as a monitoring
company, mobile phone, or pocket
pager). The communication fault clears
once the control panel successfully
reports to the receiving party.
To determine which receiver failed to
communicate, press and hold the [6] key.
10. Date and Time
Programming the date and time is only required
when you need functions such as automatic test
reports, automatic arming, and history events to
operate correctly.
How to Program the Date and Time
1. Enter your four character Master Code,
followed by [6] and the [#] key (for example,
[25806#]).
Three beeps sound, and the STAY and
AWAY indicators flash.
2. Enter the day, month, year, hour, and minute
(DD, MM, YY, HH, MM format) (for
example, DD = day of the month, MM =
month of the year, YY = current year, HH =
hour of the day, MM = minute of the day).
To program the hour of the day, use the 24:00
hour format.
Bosch Security Systems | 3/04 | SUB-MA48XO-3318
Date and Time
3. Press the [#] button to exit and return to the
disarmed state.
Two beeps sound, and the STAY and AWAY
indicators turn off. If a long beep sounds, an
error was made when entering the date and
time.
11.
Turning Outputs On/Off
This feature is only applicable if your installer set
up an output that can be turned on or off by the
codepad. The output programmed by your
installer can control a pool pump or outside
lighting. Up to three separate outputs can be
programmed.
How to Turn an Output On or Off
1. Enter your four character Master Code,
followed by [5] and the [#] key (for example,
[25805#]).
Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the output number (1 to 3).
3. Press the [#] key to turn the output on, or
press the [*] key to turn the output off.
Three beeps sound if the output is turned on,
and two beeps sound if the output is turned
off.
Repeat Step 2 and Step 3 if more than one
output is required to be turned on or off.
4. Press the [#] key to exit this function.
Two beeps sound and the STAY and AWAY
indicators turn off.
12. Reset Latching Outputs
This feature is only applicable if your installer
programmed an output to latch (remain on) until
you acknowledge the event that occurred.
How to Reset Latching Outputs
Hold down the [7] key until two beeps sound.
The output resets.
13. Telco Arm/Disarm
Sequence (Call Forward
On/Off)
Use this feature to program the Telco Arm
Sequence and Telco Disarm Sequence.
13.1
Telco Arm Sequence
Use to program the Call Forward – Immediate On
sequence or Call Forward – No Answer sequence
to automatically operate when you arm the system
in the AWAY Mode. This feature is only available
if your telecommunications provider has the call-
forward option available.
EN | 13
Hide quick links:
Advertisement
Table of Contents
