Unipulse F805AT-CK Manuals

Manuals and User Guides for Unipulse F805AT-CK. We have 1 Unipulse F805AT-CK manual available for free PDF download: Operation Manual

Unipulse F805AT-CK Operation Manual (129 pages)

CHECKER SCALE CONTROLLER

Brand: Unipulse | Category: Controller | Size: 4.98 MB

Table of Contents
7
1． Features of F805At-Ck
12
Dynamic Mode
12
Static Mode
14
Points to be Noted in Measuring
15
Interfaces of Weighing Controller
16
Graphic
16
2． Appearance Description
17
Front Panel
17
Touch Panel Type Color Liquid Display
17
Power Source Lamp
21
Rear Panel
22
3． Screen Composition and Settings
24
Screen Configuration Flow Chart
24
Entire Screen
24
Main Screen (Message)
25
The Way of Setting
25
Setting Item Selection
25
Setting Mode
26
Setting Mode of Items on Code
27
4． Way of Connection
29
Load Cell Connection
29
6-Wire Connection
30
How to Wire Load Cell Connector
31
Connecting Load Cells in Parallel
32
Sensor Cable
32
Connecting Power Input Terminal at the DC Spec
33
Connection of the Protective Ground
33
F 2-Wire Serial Interface
34
FII High Speed Bi-Directional 2- Wire Serial Interface
34
External In/Out Signal
35
Control Connector-Pin Assignment
35
Equivalent Circuit (Input)
36
Equivalent Circuit (Output)
36
RS-232C Connector
37
Connector Pin Assignment
37
Cable
37
5． Calibration
38
What Is Span Calibration
38
Calibration Procedure
39
Secondary Calibration Procedure (Equivalent Calibration)
40
Preparation for Calibration
41
LOCK Release
41
Load Cell Excitation
42
Unit
42
Decimal Place
42
Capacity
42
Minimum Scale Division
43
Balance Weight
43
Gravitational Acceleration
43
1/4 Scale Division
44
Zero Calibration
45
Span Calibration
46
Do Secondary Calibration (Equivalent Calibration)
47
Net Over/ Gross over
47
6． Function Setting
48
Operation
48
Display Frequency
48
Digital Filter
48
Analog Filter
48
Motion Detection
49
Zero Tracking
50
Digital Zero
51
Digital Zero Clear
51
Digital Zero Regulation Value
51
Function
52
Tare Subtraction/ Tare Subtraction Reset
52
Preset Tare Weight 1/ Preset Tare Weight 2
53
Auto Accumulation Command
53
Weighing Code Selection/ Setting Code Selection
54
TARE/DZ Key Disablement
55
GROSS/NET Key Disablement
55
Each Code Key Disablement
56
Accumulation Command Acceptance
56
Tare Display
56
I/O Monitor Display
57
7． Function as a Weight Checker
58
About Measurement
58
Dynamic Mode
58
Static Mode
59
Points to be Noted in Measuring
60
Each Code
61
Final
61
Over
61
Under
62
Accumulation Clear
62
Total Comparison/ Total Limit/ Count Limit
62
Comparison
63
U/L Limit Comparison/ Upper Limit/ Lower Limit
63
Near Zero Comparison/ Near Zero
64
Over/Under Comparison 1
64
Complete Output Time
64
Sequence Mode
65
Empty Count/ Take in Count
65
Average Mode/ Sample Mode
65
Gross Ratio
67
One-Touch Final
68
8． Statistics・Accumulation Control Function
69
Result
69
Result Display Screen
69
Statistical Data Display Screen
70
Accumulation Command Acceptance
71
Accumulation Clear
71
Total Comparison/ Total Limit/ Count Limit
71
Auto Accumulation Command
73
9． Graphic Screen
75
Graphic Drawing Point
75
Graphic Display
75
Relative Time/ Absolute Time
76
Graphic Mode
77
Trigger Level
78
Time Axis)-End Point
78
Y (Weight)-Start Point
78
Y (Weight)-End Point
78
10． System Mode
79
Back Light Auto. Light
79
Back Light Low Time
79
Back Light on Time
79
Self-Check
80
Language
82
Pass Word
82
Lock (Soft)
83
11． Control I/O (External Signal)
84
Control Connector-Pin Assignment
84
Equivalent Circuit (Input)
85
Equivalent Circuit (Output)
85
External Input Signal
86
G/N <Edge Input> [Pin 2]
86
Digital Zero (D/Z ON) <Edge Input> [Pin 3]
86
Tare Subtraction (TARE ON) <Edge Input> [Pin 4]
86
Tare Reset (TARE OFF) <Edge Input> [Pin 5]
86
Accumulation Command <Edge Input> [Pin 8]
87
Accumulation Clear <Edge Input> [Pin 9]
87
Input Signals Used in Weighing
87
Code No. Designation <Level Input> [Pin 11 ~ 14, 36 ~ 39]
88
Code No. Designation Selection <Level Input> [Pin 30]
88
Graph Drawing <Edge Input> [Pin 32]
88
External Output Signal
89
Near Zero [Pin 17]
89
Lower Limit, Upper Limit [Pin 43, 44]
89
Stable [Pin 45]
89
Weight Error [Pin 46]
89
Run or Total Limit [Pin 49]
89
Under, Go, over [Pin 21 ~ 23]
89
Complete [Pin 24]
89
12． Interface
90
F 2-Wire Serial Interface
90
FII High Speed Bi-Directional 2- Wire Serial Interface
91
RS-232C Interface
93
Communication Specifications
93
Setting Values for RS-232C
93
Cable
94
Communication Format
95
Communication Mode
103
Transmission Format
105
13． over Scale & Error
107
Over Scale (Weight Error [Pin 46])
107
Calibration Error
107
EXC Error
107
Priority of Error Display
107
14． Trouble Shooting
108
15． Block Diagram
113
16． Dimensions
114
17． Mounting on a Panel
115
18． Specifications
116
Analog
116
Display
116
Configuration
117
Control Input/Output Signal
117
Interface
117
General Specifications
119
Attachment
120
19． the List of Initial Setting Value
121
20． Mode Setting Tree Chart
126
21． Statement of Conformation to Ec Directives
127
(Designated When It Is Shipped)
127

Unipulse Categories

Measuring Instruments Touch Panel Controller

Monitor Accessories

More Unipulse Manuals

Unipulse F805AT-CK Manuals

Unipulse F805AT-CK Operation Manual (129 pages)

Table of Contents

Related Products

Unipulse Categories