IVECO VECTOR 8 Diesel Engine Manuals

Manuals and User Guides for IVECO VECTOR 8 Diesel Engine. We have 1 IVECO VECTOR 8 Diesel Engine manual available for free PDF download: Technical And Repair Manual

IVECO VECTOR 8 Technical And Repair Manual

IVECO VECTOR 8 Technical And Repair Manual (206 pages)

Industrial application

Brand: IVECO | Category: Engine | Size: 14 MB

Table of Contents

General Specifications

15
Table of Contents

29
- High-Pressure Electronic Injection
  31
  - Fuel System (Common Rail)
    31
  - General Information
    31
  - Description of the System
    31
  - Electrical System
    31
- Operation
  33
Industrial Application

53
- General Specifications
  55
  - Clearance Data - 8 Cyl
    59
- Part One
  61
  - Mechanical Components
    61
- Engine Overhaul
  63
  - Preface
    63
  - Dismantling
    63
  - Installation of Components for the Application
    74
  - Fitting the Flywheel Cover Housing
    74
  - Fitting the Rear Oil Seal
    75
- Engine Flywheel
  75
  - Fitting the Engine Flywheel
    75
  - Fitting the Gearbox
    77
- Jumpers
  79
- Rocker Arm Assembly
  79
- Rocker Arm Support Rockers
  79
- Rocker Arms
  79
- Rods
  79
- Lubrication
  83
  - Oil Pump
    84
- Completing the Engine
  85
- Common Rail Assembly Procedure
  90
- Second Part
  95
  - Electrical Equipment
    95
- Location of Components on the Engine
  97
- Third Part - Diagnostics
  107
- Troubleshooting
  109
  - General Information
    109
- Troubleshooting with Tool 99368550
  110
  - Connection Procedures
    110
  - Diagnosis Procedures for Vector 8V Engines
    111
  - Diagnosis Environment
    112
- Engine Parameter Reading
  115
- Reading Parameter for Save Code
  116
- Ilc Simulator 99368543 Tool
  122
- Fourth Part
  129
  - Planned Maintenance
    129
- Vector 8 Dragon Fvae2884A*B200 Maintenance Plan
  131
- Vector 8 Genset Fvae2885X*A100 Maintenance Plan
  133
- Description of Preventive and Routine Maintenance Work
  135
- Changing Engine Oil Filters
  136
- Checking/Refilling Engine Oil Filters
  136
- Changing the Engine Oil
  138
- Changing Fuel Prefilter and Water Separator Filter
  139
- Adjusting Rocker Arm Assembly
  140
- Changing Fuel Filters
  143
- Changing an Injector
  145
- Changing Blow-By Filter
  147
- Changing Primary System Pump
  148
  - Removal
    148
  - Fitting
    149
- Removing/Refitting Starter Motor
  150
  - Removal
    150
  - Fitting
    150
Overhaul and Technical Specifications

151
- General Specifications
  153
- Assembly Clearance Data
  154
- Engine Overhaul
  160
  - Dismantling the Engine at the Bench
    160
- Repair Operations
  161
  - Cylinder Unit
    161
  - Checks and Measurements
    161
  - Replacing Cylinder Liners
    162
- Timing System
  164
  - Camshaft
    164
  - Checking Cam Lift and Pin Alignment
    164
  - Replacing the Camshaft Idle Gear
    164
  - Changing the Bushings
    166
  - Changing the Tappets
    166
  - Fitting Tappets and Camshaft
    166
- Output Shaft
  166
  - Measuring Journals and Crankpins
    166
  - Checking Main Journal Alignment
    168
  - Crankshaft Balancing Instructions
    169
  - Replacing Water Pump Drive Gear
    169
  - Changing the Oil Pump and Timing System Gear
    170
  - Fitting the Main Bearings
    170
  - Finding Journal Clearance
    171
  - Tightening Sequence
    171
  - Checking Crankshaft Thrust Clearance
    172
  - Camshaft Timing
    173
- Piston Rod Assembly
  178
  - Pistons
    178
  - Measuring the Piston Diameter
    178
  - Gudgeon Pins
    178
  - Conditions for Correct Mating of Gudgeon Pin and Piston
    179
  - Piston Rings
    179
  - Connecting Rods
    180
  - Check of Connecting Rod Alignment
    181
  - Fitting the Connecting Rod-Piston Assembly
    181
  - Connecting Rod-Piston Mating
    181
  - Fitting the Piston Rings
    181
  - Check of Rod/Piston Alignment
    182
  - Fitting the Rod-Piston Assemblies into the Cylinder Liners
    182
  - Measuring the Mounting Clearance of Big End Pins
    183
  - Fitting the Connecting Rod Caps
    183
  - Check of Piston Protrusion
    183
- Cylinder Head
  184
  - Hydraulic Leak Test
    184
  - Dismantling Valves
    184
  - Checking the Cylinder Head Support Surface
    184
- Valve
  184
- Valve Guides
  185
  - Replacing the Valve Guides
    186
  - Reaming the Valve Guides
    186
  - Replacing and Regrinding the Valve Seats
    186
- Replacing the Injector-Holder Cases
  187
- Fitting the Valves
  188
- Installing the Cylinder Head
  188

Advertisement

Advertisement

Related Products

IVECO Categories

Engine Trucks Automobile Car Navigation system Buses

More IVECO Manuals