ITech IT8701 Manuals

Manuals and User Guides for ITech IT8701. We have 2 ITech IT8701 manuals available for free PDF download: Programming Manual, User Manual

ITech IT8701 Programming Manual

ITech IT8701 Programming Manual (133 pages)

DC Programmable Electronic Loads

Brand: ITech | Category: Test Equipment | Size: 0 MB

Table of Contents

Limitation of Warranty
3
Safety Symbols
3
Warranty
3
Safety Precautions
4
Environmental Conditions
5
Regulatory Markings
5
Waste Electrical and Electronic Equipment (WEEE) Directive
6
Compliance Information
7
Table of Contents
8
Chapter1 Remote Control

13
- Communication Interfaces
  13
- Programming the Status Registers
  16
- Condition Registers
  19
- Event Registers
  20
- Enable Registers
  20
- Queues
  21
  - Output Queue
    21
  - Error Queue
    21
- Status Byte and Service Request (SRQ)
  21
  - Status Byte Register
    21
- Service Request Enable Register
  22
- Serial Poll and SRQ
  23
- Trigger Model (GPIB Operation)
  23
  - Idle and Initiate
    24
  - Trigger Model Operation
    24
Chapter2 SCPI Introduction

26
- SCPI Introduction
  26
- Types of SCPI Commands
  26
  - Multiple Commands in a Message
    27
  - Moving Among Subsystems
    27
  - Including Common Commands
    28
  - Case Sensitivity
    28
  - Long-Form and Short-Form Versions
    28
  - Using Queries
    29
- Types of SCPI Messages
  29
  - The Message Unit
    29
  - Headers
    30
  - Query Indicator
    30
  - Message Unit Separator
    30
  - Root Specifier
    30
  - Message Terminator
    30
  - Command Execution Rules
    30
- SCPI Data Formats
  31
  - Response Data Types
    32
- SCPI Command Completion
  33
- SCPI Conformance Information
  34
  - Language Dictionary Introduction
    34
- Subsystem Commands
  35
Chapter3 IEEE-488 Command Reference

36
- CLS - Clear Status
  37
- ESE <Nrf> - Event Enable
  37
- Esr
  38
- Idn
  39
- Rdt
  39
- Opc
  39
- Rcl
  40
- Rst
  41
- Sav
  42
- Sre
  43
- Stb
  44
- Trg
  44
- Tst
  45
- Wai
  45
Chapter4 System Commands

47
- System:preset
  47
- System:posetup
  47
- System:version
  48
- System:error
  48
- System:clear
  49
- System:local
  49
- System:remote
  49
- System:rwlock
  50
Chapter5 Status Subsystem

51
- Status:channel
  51
- Status:channel:condition
  51
- Status:channel:enable
  52
- Status:csum
  52
- Status:csummary:enable
  53
- Status:operation
  53
- Status:operation:condition
  54
- Status:operation:enable
  54
- Status:questionable
  55
- Status:questionable:condition
  56
- Status:questionable:enable
  56
- Status:preset
  57
Chapter6 IT873X Specific Commands

58
- Trace Command Summary
  58
- Channel Command Summary
  58
- Source Command Summary
  58
- Sense Command Summary
  61
- Measure, Fetch Command Summary
  62
- Calibrate Command Summary
  62
- Remote Analog Control Command
  63
Chapter7 SCPI Measurement Command

64
- Fetch:voltage[:DC]
  64
- Measure:voltage[:DC]
  64
- Fetch:voltage:max
  64
- Measure:voltage:max
  64
- Fetch:voltage:min
  65
- Measure:voltage:min
  65
- Fetch:current[:DC]
  65
- Measure:current[:DC]
  65
- Fetch:current:max
  66
- Measure:current:max
  66
- Fetch:current:min
  66
- Measure:current:min
  66
- Fetch:power[:DC]
  67
- Fetch:capability
  67
- Measure:capability
  67
- Fetch:allvoltage
  67
- Measure:allvoltage
  67
- Fetch:allcurrent
  68
- Measure:allcurrent
  68
- Measure:allpower
  68
Chapter8 Channel Subsystem

70
- Channel
  70
- Channel:ID
  70
Chapter9 Trace Subsystem

72
- Trace:clear
  72
- Trace:free
  72
- Trace:points
  72
- Trace:feed
  73
- Trace:feed:control
  74
- Trace:data
  74
- Trace:filter
  75
- Trace:delay
  75
- Trace:timer
  76
Chapter10 Source Subsystem

77
- [Source:]Input:all
  77
- [Source:]Input
  77
- [Source:]Input:control
  78
- [Source:]Input:syncon
  78
- [Source:]Input:short
  79
- [Source:]Input:timer
  79
- [Source:]Input:timer:delay
  80
- [Source:]Remote:sense
  81
- [Source:]Function
  81
- [Source:]Function:mode
  82
- [Source:]Transient
  83
- [Source:]Input:protection:clear
  83
- [Source:]Current
  84
- [Source:]Current:range
  84
- [Source:]Current:slew
  85
- [Source:]Current:slew:positive
  86
- [Source:]Current:slew:negative
  87
- [Source:]Current:protection:state
  87
- [Source:]Current:protection
  88
- [Source:]Current:protection:delay
  89
- [Source:]Current:transient:mode
  89
- [Source:]Current:transient:alevel
  90
- [Source:]Current:transient:blevel
  90
- [Source:]Current:transient:awidth
  91
- [Source:]Current:transient:bwidth
  91
- [Source:]Current:high
  92
- [Source:]Current:low
  92
- [Source:]Current:triggered
  92
- [Source:]Voltage
  93
- [Source:]Voltage:range
  94
- [Source:]Voltage:range:auto[:State]
  94
- [Source:]Voltage:on
  95
- [Source:]Voltage:latch
  96
- [Source:]Voltage:high
  96
- [Source:]Voltage:low
  96
- [Source:]Voltage:triggered
  97
- [Source:]Resistance
  97
- [Source:]Resistance:range
  98
- [Source:]Resistance:high
  99
- [Source:]Resistance:low
  99
- [Source:]Resistance:vdrop
  100
- [Source:]Resistance:led[:State]
  100
- [Source:]Resistance:triggered
  101
- [Source:]Power
  101
- [Source:]Power:range
  102
- [Source:]Power:high
  103
- [Source:]Power:low
  103
- [Source:]Power:protection
  103
- [Source:]Power:protection:delay
  104
- [Source:]Power:config
  105
- [Source:]Power:triggered
  106
- [Source:]Impedance
  106
  - [Source:]Impedance:range
    107
  - [Source:]Impedance:resistance
    107
  - [Source:]Impedance:induction
    108
  - [Source:]Impedance:capacitance
    109
  - [Source:]Impedance:high
    109
  - [Source:]Impedance:low
    109
Chapter11 List Commands

111
- [Source:]List:range
  111
- [Source:]List:count
  111
- [Source:]List:step
  112
- [Source:]List:level
  112
- [Source:]List:slew
  113
- [Source:]List:width
  114
- [Source:]List:sav
  114
- [Source:]List:rcl
  115
Chapter12 Sense Subsystem

116
- Sense:average:count
  116
Chapter13 Calibration Subsystem

117
- Calibrate:secure[:State]
  117
- Calibrate:initial
  118
- Calibrate:save
  118
- Calibrate:current:point
  118
- Calibrate:current[:Level]
  119
- Calibrate:current:meter:point
  119
- Calibrate:current:meter[:Level]
  120
- Calibrate:voltage:point
  120
- Calibrate:voltage[:Level]
  121
- Calibrate:voltage:meter:point
  121
- Calibrate:voltage:meter[:Level]
  122
Chapter14 Programming Examples

123
- Introduction
  123
- Programming the Input
  123
  - Power-On Initialization
    123
  - Enabling the Input
    123
  - Input Voltage
    124
  - Maximum Voltage
    124
  - Input Current
    124
  - Maximum Current
    124
  - Overcurrent Protection
    124
  - Setting the Triggered Voltage or Current Levels
    124
  - Generating Triggers
    125
  - Programming Transients
    125
Chapter15 Error Messages

129

Advertisement

ITech IT8701 User Manual

ITech IT8701 User Manual (73 pages)

DC Programmable Electronic Loads

Brand: ITech | Category: Chassis | Size: 4 MB

Table of Contents

Limitation of Warranty
3
Safety Symbols
3
Safety Precautions
4
Environmental Conditions
5
Regulatory Markings
5
Waste Electrical and Electronic Equipment (WEEE) Directive
5
Compliance Information
7
Table of Contents
8
DC Programmable Electronic Loads

10
- Quality Certification and Assurance
  10
- Warranty
  10
- Module Installation
  10
  - Channel Number
    11
- Verifying the Shipment
  10
- Mainframe Installation
  12
  - Installation Size Introduction
    12
- Connecting the Power Cord
  16
Chapter1 Inspection And Installation

10
Chapter2 Quick Start

18
- Brief Introduction
  18
- Introduction
  19
- Front Pannel Introduction
  20
- Rear Panel Description
  20
- Power-On Selftest
  21
Chapter3 Panel Function Introduction

23
- Mainframe Operation
  23
  - Mainframe Keyboard Functions Introduction
    23
  - Menu List
    24
  - Channel Option
    29
  - Save and Recall
    29
  - Configuration Menu Introduction
    29
  - Module Keyboard Lock
    29
- Module Operation
  30
  - Single Channel Module Panel
    30
  - Dual Channel Module Panel
    30
- VFD Indicator Function Description
  31
- 8-Pin Control Connector
  32
  - External Trigger Connections
    33
  - External ON/OFF Control Connection
    33
- Extended Frame Connections
  34
- Controlling Link
  34
  - Voltage Failure Indication
    35
  - Current Monitoring
    35
  - Digital I/O
    35
  - Remote Measurement Connection
    35
  - External Analogue Control
    36
- Load Connection
  36
- Parallel Connections
  37
Chapter4 Operations Introduction

38
- Local/Remote Operation
  38
- PC Control Connection
  38
- Operating Modes
  38
  - Constant Current (CC) Mode
    39
  - Constant Resistance (CR) Mode
    40
  - Constant Voltage (CV) Mode
    40
  - Constant Power (CW) Mode
    41
  - Operations
    42
- Transient Operation
  43
  - Continuous
    44
  - Pulsed
    44
  - Toggled
    44
  - A/B Transient Operations
    45
- List Operation
  46
- Triggered Operation
  49
  - Trigger Function
    49
  - Trigger Source
    49
- Short Operation
  49
- Input On/Off Operation
  49
- Synchronous Load
  50
- Von Operation
  50
- Protection Functions
  52
- Save and Recall Operation
  53
- Automatic Test
  53
- CR-LED Test Function
  57
Chapter5 Specifications

58
- Main Technical Parameters
  58
- Supplementary Characteristics
  66
Chapter6 Remote Operation

68
- RS232 Interface
  68
- Ether Net Interface
  70
- GPIB Interface
  70
- USB Interface
  70
Appendix

72
- Specifications of Red and Black Test Lines
  72

Advertisement

Related Products

ITech Categories

Power Supply

Power Supply Test Equipment Measuring Instruments Watch Racks & Stands

More ITech Manuals