Muratec MFX-C4000 Field Engineering Manual page 163

Code Displayed Name
109-0002 Fuser Fan Run Ready
109-0003 Fuser Motor Forward
109-0004 Fuser Fan Run
109-0005
Fuser Bias
109-0006 Heater Over Heat Sensor
109-0007 Heater Low Heat Sensor
109-0008 Heater Open Heat Sensor
110-0000 LSU Motor1 Run Ready
110-0001 LSU Motor2 Run Ready
110-0002 LSU Fan1 Run Ready
110-0003 LSU Fan2 Run Ready
110-0004 LSU Clean Motor
110-0005
LSU Clean Sensor
110-0006 LSU Motor1 Run
110-0007 LSU Motor2 Run
110-0008 LSU LD Power1
110-0009 LSU LD Power2
110-0010 LSU LD Power3
110-0011 LSU LD Power4
110-0012 LSU Fan1 Run
110-0013 LSU Fan2 Run
111-0000 Toner Dispense Motor
Yellow
111-0001 Toner Dispense Motor
Magenta
111-0002 Toner Dispense Motor Cyan
Toner Dispense Motor Black Toner Dispense(Supply) Motor On/Off
111-0003
111-0004 Toner Sensor Yellow
111-0005
Toner Sensor Magenta
111-0006 Toner Sensor Cyan
111-0007 Toner Sensor Black
ACR Execute Now
112-0000
113-0000 Finisher Present Sensor
113-0001 Entrance Motor
113-0002 Exit Motor
113-0003 Paddle Motor
Service Manual
Alignment & Troubleshooting
Detects if Fuser Fan Motor runs at normal speed.
Fuser Motor Forward On/Off
Fuser Fan Motor On/Off
Fuser bias voltage on at normal drive level
Detect if the Heater is in Overheat Status.
Detect if the Heater is in Lowheat Status.
Detect if the Heater is in Openheat Status.
Detects if LSU motor1 runs at normal speed.
Detects if LSU motor2 runs at normal speed.
Detects if LSU Fan Motor runs at normal speed.
Detects if LSU Sub Fan Motor runs at normal speed.
Detect if the LSU Clean Motor On/Off
Detect if the LSU Clean Motor is On or Off
LSU Motor1 On/Off
LSU Motor2 On/Off
LSU LD1 Power On/Off (yellow)
LSU LD2 Power On/Off (magenta)
LSU LD3 Power On/Off (cyan)
LSU LD4 Power On/Off (black)
Start/Stop LSU Fan Run
Start/Stop LSU Sub Fan Run
Toner Dispense(Supply) Motor On/Off
Toner Dispense(Supply) Motor On/Off
Toner Dispense(Supply) Motor On/Off
TC sensor in developer tank.
TC sensor in developer tank.
TC sensor in developer tank.
TC sensor in developer tank.
Start Auto Color Registration
Detect if the Finisher is in place.
Entrance Motor run as IOT Speed <about 5 sec>
Exit Motor run as IOT Speed <about 5 sec>
Paddling
4-57
Meaning State
Displayed
High[Low]
On[Off]
On[Off]
On[Off]
High[Low]
High[Low]
High[Low]
High[Low]
High[Low]
High[Low]
High[Low]
High[Low]
High[Low]
On[Off]
On[Off]
On[Off]
On[Off]
On[Off]
On[Off]
On[Off]
On[Off]
On[Off]
On[Off]
On[Off]
On[Off]
x.xx voltage
x.xx voltage
x.xx voltage
x.xx voltage
Install
[Not Install]
On[Off]
On[Off]
On