Using The Anyfi™ Wireless Dmx Receiver; Setting The Fixture To Receive Wireless Signal; Resetting The Wireless; Select W-Dmx™ Or Standard 2.4Ghz Receiver - Blizzard Lighting Colorise Quadra Manual

Using the AnyFi™ Wireless DMX Receiver
In addition to the unbridled thrill you already received the first time you turned on your
fixture, you'll be delighted to know that your Colorise™ Quadra is equipped to work
seamlessly with our own Skywire™ 2.4GHz wireless DMX products,
as well as W-DMX™ wireless products. W-DMX™ is a two-time
award winning wireless DMX technology, created and owned by
Wireless Solution Sweden AB.
Skywire™ wireless DMX products feature 512 auto-assigning
frequencies in 7 groups allowing up to 7 systems to run
simultaneously in the same space, completely free of interference,
with reliable wireless communication for over 1000 feet line-of-
sight! Using W-DMX™ wireless, you can expect an outstanding wireless range of up to 500
meters (line-of-sight), very easy setup, and leave any worries behind concerning loss of signal
due to its built-in FHSS technology (Frequency Hopping Spread Spectrum).
So first, if you would like to use Standard 2.4GHz wireless DMX, you will need a Blizzard
wiCICLE® transmitter, Lightcaster™ transceiver, or any Blizzard Lighting controller that has
this type of built-in wireless transmitter, like our Kontrol 6 Skywire™ to act as a transmitter.
And if you plan on using W-DMX™ 2.4GHz wireless for your setup, you will need a W-DMX™
transceiver to broadcast the signal from your controller, such as our Lightcaster W-DMX™.
Ready to move on? Well alrighty!
1.) IMPORTANT
a.) Navigate the main menu to reach SET, press <ENTER>, then use the <UP/
DOWN> buttons until SIGN is displayed, then press <ENTER> again. Now use the
<UP/DOWN> buttons to highlight 2.4G (wireless mode), and press <ENTER> to
confirm.

2.) Resetting The Wireless

a.) Navigate the main menu to reach SET, press <ENTER>, then use the <UP/
DOWN> buttons until WIRE is displayed, then press <ENTER> again.
b.) From here, you can use the <UP/DOWN> buttons to highlight REST and press
<ENTER>, select YES, then <ENTER> to reset the wireless setup.
3.) Select W-DMX™ or Standard 2.4GHz Receiver
a.) Make sure the device you are using to transmit signal with is powered on.
b.) Navigate the main menu to reach SET, press <ENTER>, then use the <UP/
DOWN> buttons until WIRE is displayed, then press <ENTER> again.
c.) Now use the <UP/DOWN> buttons to highlight KEY in the menu, and press
<ENTER>.
d.) At this point, please note that every time you touch the <ENTER> button, the
wireless LED status indicator changes between 4 colors (but only 2 are functional):
• GREEN: W-DMX™ 2.4 GHz Mode
• YELLOW: Standard 2.4 GHz Mode (wiCICLE™ & LightCaster Compatible)
RED
*Note:
e.) While the LED indicator is illuminated in
Standard 2.4GHz), press and hold the <ENTER> button for 3 seconds to make your
chosen wireless type the active wireless DMX signal type.
For W-DMX™ connections, you should be done. The fixture will detect the signal!
*For Standard 2.4GHz connections, please continue to Step 5 on the next page.
Colorise™ Quadra Manual Rev. A
- Set the Fixture to Receive Wireless Signal in the Control Panel
BLUE
and currently have no function during this selection process.
GREEN (for W-DMX) or
Page 10
Universal Wireless DMX
YELLOW (for
© 2015 Blizzard Lighting, LLC