Table of Contents
Advertisement
Quick Links
XSD10Z-2
Model:
True Day/Night 550/600 TVL Vandal Resistant Mini
Speed Dome CCTV Camera with 10x Optical Zoom
PLEASE READ THIS MANUAL BEFORE YOU INSTALL OR START USING THE XSD10Z-2 SPEED DOME
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the interference at the user's own expense.
PRECAUTIONS:
z Only qualified and experienced person can carry out the installation. In many countries and areas licensed personnel is required
z Always take safety codes into consideration during installation.
z Use reliable tools only, poor quality tools may cause damage to both human and property
z Check the strength of all items onsite that are related to installation in advance. It is recommended that the stand of dome be at
least 4 times stronger than the weight of the dome and its accessories.
z Keep all the original dome package materials in case of future repacking and transportation.
z Choose and install speed dome according to environment requirement (Refer to the Product Features).
WARNINGS:
z Avoid installing this speed dome in hazardous places where inflammable or explosive materials are stored or used.
z This speed dome runs on 12V DC, 800mA.
z Connect to power only after completing installation.
z Disassembling of the camera can only be carried out by qualified personnel.
z Use soft towel to clean the down cover when necessary. Avoid using caustic detergent.
z Avoid aiming camera to strong light.
XSD10Z-2
Model:
True Day/Night 550/600 TVL Vandal
Resistant Mini Speed Dome CCTV Camera
with 10x Optical Zoom
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for XVision XSD10Z-2
Summary of Contents for XVision XSD10Z-2
- Page 1 Speed Dome CCTV Camera with 10x Optical Zoom PLEASE READ THIS MANUAL BEFORE YOU INSTALL OR START USING THE XSD10Z-2 SPEED DOME This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
-
Page 2: Table Of Contents
INDEX PRODUCT DESCRIPTION MENU FUNCTIONS FEATURES Main Menu INSTALLATION Display Setup Contents 7.2.1 Set North Direction 7.2.2 Privacy Zone Mask Setup Install Wall Mounting Guide Camera Setup DIP SWITCH SETUP 7.3.1 White Balance Setup Communication Protocol Setup 7.3.2 Auto Exposure Setup Camera ID Setup Motion Setup Reserved for Supplier... -
Page 3: Product Description
1. Product Description The XSD10Z-2 is a Professional True Day/Night Speed Dome with 10x Zoom with Mechanical IR Filter (making it IR sensitive for use with Infra Red lighting). This camera is designed for use in very high risk applications where very high quality surveillance is required and features an Xvision Auto Iris Zoom Lens with Semi-Auto or Auto Focus and 100x Zoom (10x Optical + 10x Digital) for easy selection of any viewing angle between 10 and 71°. -
Page 4: Installation
Installation Holes 3.3 WALL MOUNTING GUIDE NOTE: THE WALL MOUNT IS NOT SUPPLIED WITH THE XSD10Z-2. 1. Drill holes on the wall using the mounting hole position, and install the plastic anchor to the wall mount. 2. Feed the control cable, video cable and power cable through the wall bracket cavity 3. -
Page 5: Dip Switch Setup
4. DIP Switch Setup Before you install the camera, you should set the DIP switches to configure the camera ID and communication protocol. COMMUNICATION PROTOCOL CAMERA ID OPTIONS ADDRESS (ID) FUNCTION PROTOCOL FUNCTION A0 64 128 Refer to the Manual Reserve NTSO 4.1 COMMUNICATION PROTOCOL SETUP... -
Page 6: Cabling
5. Cabling Before you install the camera, you should set the DIP switches to configure the camera ID and communication protocol. Cable Terminal Block IN 1 IrDA IN 2 Sensor IN 3 IN 4 Door Switch IN COM+ SENSOR VIDEO- VIDEO+ RS-485+ RS-485-... -
Page 7: Video Connection
5.3 VIDEO CONNECTION z Connect with BNC Coaxial Cable 5.4 ALARM INPUT CONNECTION (Optional) z Sensor Input Before connecting sensors, check driving voltage and output signal type of the sensor. Since output signal types of the sensors are divided into Open Collector and Voltage Output type in general,the cabling must be done properly after considering these typed. -
Page 8: Operation
6. Operation Check points before operation z Before power is applied, please check the cables carefully. z The camera ID of the controller must be identical to that of the target camera. The camera ID can be checked by reading the DIP switch of the camera. -
Page 9: Starting Osd Menu
6.1 STARTING OSD MENU Using the OSD menu, Preset, Pattern, Swing, Group and Alarm Input function can be configured for each application. z Enter Menu - <Go Preset>[95] 6.2 RESERVED PRESET Some Preset numbers are reserved to special functions. <Go Preset> [95] :Enters into OSD menu <Go Preset>... -
Page 10: Pattern
6.5 PATTERN The Pattern Function allows the camera to follow a user defined trajectory set by a joystick or controller for an assigned time path. 4 Patterns are available and a maximum of 1200 communication commands can be stored per pattern. z Set Pattern Pattern can be created by following the steps below: - Enter OSD Menu >... -
Page 11: Other Functions
6.7 OTHER FUNCTIONS z Power Up Action This function enables to resume the last action executed before power down. Most of actions such as Preset, Pattern, Swing and Group are available for this function but jog actions are not available to resume z Auto Flip In case that tilt angle arrives at the top of tilt orbit (90°), zoom module camera keep moving to... -
Page 12: Menu Functions
7. Menu Functions General Rules of Key Operation for Menu z The menu items surrounded with ( ) always has its sub menu. z For aIl menu level, to go into sub menu, press NEAR key z To go to up-one-level menu, press FAR key. z To move from item to item in the menu, use the joystick in the Up/Down or Left/Right. -
Page 13: Set North Direction
7.2.1 Set North Direction SET NORTH DIRECTION MOVE TO TARGET POSITION [NEAR: SAVE] [FAR: CANCEL] Go to the function <Set North Direction> to assign compass direction to north. Move camera and press NEAR button to save. 7.2.2 Privacy Zone Mask Setup PRIVACY ZONE MASKNO UNDEFINED... -
Page 14: Camera Setup
7.3 CAMERA SETUP Use this menu to setup the general functions of zoom camera module. ZOOM CAMERA SETUP FOCUS MODE SEMIAUTO DIGITAL ZOOM LINE LOCK <WHITE BALANCE SETUP> <AUTO EXPOSURE SETUP> BACK EXIT Focus Mode: [AUTO/MANUAL/SEMIAUTO] z SEMIAUTO Mode exchanges focus mode automatically between Manual Focus mode and Auto Focus mode z Manual Focus mode activates in preset mode. -
Page 15: Motion Setup
z Backlight [ON/OFF] Sets Bacldight Compensation z Day/Night [AUTO1/AUT02DAY/NIGHT] AUT01 exchanges Day/Night mode faster than AUT02. z Brightness [0-100] Adjusts brightness of images. Iris, Shutter Speed and Gain are adjusted automatically in correspondence with this value z Iris [AUTO/MANUAL(0~100)] if Iris is set to Auto Iris should have highest priority in adjusting AE and Shutter Speed should be fixed. If Iris is set to Manual, Iris should be fixed aa Iris has lower priority in adjusting AE. -
Page 16: Parking Action Setup
7.4.1 Parking Action Setup PARKING ACTION SETUP PARK ENABLE WAIT TIME 00:10:00 PARK ACTION HOME BACK EXIT z Park Enabled [ON/OFF] If Park Enable is set to ON, the camera will run the assigned PTZ function automatically if there is no ‘’Wait Time’’ assigned z Wait Time [1 minute-4 hours] The time is displayed in HH:MM:SS”... -
Page 17: Preset Setup
7.5 PRESET SETUP Use this menu to setup the general functions of zoom camera module. PRESET SETUP PRESET NO. CLEAR PRESET CANCEL <EDIT SCENE> <EDIT LABEL> LABEL123 CAM ADJUST GLOBAL BACK EXIT Preset Number: [1~128] If a selected preset is already defined, the camera will move to predefined position and preset characteristics such as Label and Relay Outputs will show on the display monitor. -
Page 18: Edit Preset Label
7.5.2 Edit Preset Label Current Cursor position EDIT PRESET LABEL [_ _ _ _ _ _ _ _ _ _] 1 2 3 4 5 6 7 8 9 0 A B C D E F G H I J CANCEL K L M N O P Q R S T U V W X Y Z a b c d... -
Page 19: Pattern Setup
7.7 PATTERN SETUP PATTERN SETUP PATTERN UNDEFINED CLR PATTERN CANCEL <EDIT PATTERN> BACK EXIT Pattern Number: [1~4] Select Pattern number to edit. If a selected pattern number is not defined, ‘UNDEFINED’ will be displayed under the selected pattern number. Clear Pattern: [CANCEL/OK] Deletes data in current pattern Edit Pattern:... -
Page 20: Group Setup
7.8 GROUP SETUP GROUP SETUP GROUP NO. UNDEFINED CLEAR GROUP CANCEL <EDIT GROUP> BACK EXIT Group Number: [1~8] Select Group number to edit. If a selected Group number is not defined, ‘UNDEFINED’ will be displayed under the selected pattern number. Clear Group: [CANCEL/OK] Deletes data in current Group... -
Page 21: Initialize System
7.9 INITIALIZE SYSTEM SYSTEM INITIALIZE CLEAR ALL DATA CLR DISPLAY SET CLR CAMERA SET CLR MOTION SET CLR EDIT DATA REBOOT CAMERA REBOOT SYSTEM SAVE CANCEL Clear All Data: Deletes all configuration data such as Display, Camera, Motion setup and so on. Clear Display Set: Initializes Display Configuration Clear Camera Set:... -
Page 22: Specifications
Appendix 7: Specifications 8. Specifications Model: XSD10Z-2 Picture Type: True Day/Night Image Sensor: Sony 1/4” Super HAD CCD DSP: Xvision XX1 Resolution: 550/600 TVL Minimum Illumination: 0.005 Lux Lens Type: Auto Iris Varifocal Lens Lens Size: 3.8 to 38.0mm Lens Viewing Angle: 10 to 71°... -
Page 24: Limited Warranty
TECHNICAL SUPPORT: For Technical Support for any Xvision product please contact your local distributor. LIMITED WARRANTY: This product is supplied with a 1 Year warranty. The Warranty excludes products that have been misused, (including accidental damage) and damage caused by normal wear and tear. In the unlikely event that you encounter a problem with this product, it should be returned to the place of purchase.
Need help?
Do you have a question about the XSD10Z-2 and is the answer not in the manual?
Questions and answers