Avdel T40 Instruction Manual

Hydro-electric
Hide thumbs Also See for T40:

Advertisement

Quick Links

I n s t r u c t i o n M a n u a l
O r i g i n a l I n s t r u c t i o n
T 4 0 I n s t a l l a t i o n To o l
H y d ro - E l e c t r i c P o w e r To o l

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the T40 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Avdel T40

  • Page 1 I n s t r u c t i o n M a n u a l O r i g i n a l I n s t r u c t i o n T 4 0 I n s t a l l a t i o n To o l H y d ro - E l e c t r i c P o w e r To o l...
  • Page 3: Table Of Contents

    Avdel UK Limited policy is one of continuous product development and improvement and we reserve the right to change the specification of any product without prior notice.
  • Page 4: Safety

    17 The machine shall at all times be operated in accordance with relevant Health and Safety legislation. In the UK the "Health & Safety ® at Work Act 1974" applies. Any question regarding the correct operation of the machine must be directed to Avdel CAUTIONS AVDEL RECOMMENDS THAT ONLY HYDRAPAC UNITS BE USED TO DRIVE INSTALLATION TOOLS, AS OTHER MAKES OF HYDRAULIC POWER UNITS MAY NOT OPERATE AT THE SAFE DESIGNED WORKING PRESSURES.
  • Page 5: Intent Of Use

    S p e c i f i c a t i o n s I n t e n t o f U s e The T40 Installation Tool is basically a Piston and Cylinder Assembly. When coupled Hydraulically and Electrically to a compatible ®...
  • Page 6: Putting Into Service

    P u t t i n g i n t o S e r v i c e P r i n c i p l e o f O p e r a t i o n IMPORTANT Read the safety rules on page 4 carefully When both hoses and control cord are connected to the HydraPac, the pull and return cycles of the tool are controlled by depressing and releasing the trigger switch located in the handle respectively.
  • Page 7: Operating Instructions

    P u t t i n g i n t o S e r v i c e O p e r a t i n g I n s t r u c t i o n s ® To install a Avdelok Fastener •...
  • Page 8: Maintenance

    M a i n t e n a n c e D i s m a n t l i n g I n s t r u c t i o n s IMPORTANT Be sure the HydraPac is turned off before removing tool or nose. •...
  • Page 9: To Bleed The Tool

    M a i n t e n a n c e To B l e e d t h e To o l To Bleed the Tool: • Couple the short tool hoses directly onto a HydraPac or compatible hydraulic power source. Note: Do not use long extension hoses as these will prevent the air from escaping into the HydraPac.
  • Page 10: General Assembly For T40 Installation Tool 73414-02000

    G e n e r a l A s s e m b l y f o r T 4 0 I n s t a l l a t i o n To o l 7 3 4 1 4 - 0 2 0 0 0...
  • Page 11: Parts List For T40 Installation Tool 73414-02000

    P a r t s L i s t f o r T 4 0 I n s t a l l a t i o n To o l 7 3 4 1 4 - 0 2 0 0 0 T40 INSTALLATION TOOL PARTS LIST ITEM PART Nº...
  • Page 12: Servicing The Tool

    S e r v i c i n g t h e To o l D a i l y • Check for oil leaks. • Check the stroke of tool. • Check for worn anvil indicated by score marks on the installed collar. This can also be confirmed by referring to the installed data in the fastener catalogue.
  • Page 13: Fault Diagnosis

    F a u l t D i a g n o s i s S y m p t o m P o s s i b l e C a u s e R e m e d y P a g e R e f Tool fails to operate Inoperative HydraPac...
  • Page 14 F a u l t D i a g n o s i s S y m p t o m P o s s i b l e C a u s e R e m e d y P a g e R e f Jaw segments do not Improper operation of jaw Check internal parts of the...
  • Page 15 D e c l a r a t i o n o f C o n f o r m i t y We, Avdel UK Limited, Watchmead Industrial Estate, Welwyn Garden City, Herts, AL7 1LY declare under our sole responsibility that the product: Model: 73414-02000 Serial No.
  • Page 16 This document is for informational purposes only. Infastech makes no warranties, expressed or implied, in this document. Data shown is subject to change without prior notice as a result of continuous product development and improvement policy. Your local Avdel representative is at your disposal should you need to confirm latest information.

Table of Contents