Related Manuals for Avdel 73414-02000
Summary of Contents for Avdel 73414-02000
- Page 1 I n s t r u c t i o n M a n u a l O r i g i n a l I n s t r u c t i o n Request Info 1-800-453-1692 www.aboveboardelectronics.com T 4 0 I n s t a l l a t i o n To o l...
-
Page 3: Table Of Contents
Avdel UK Limited policy is one of continuous product development and improvement and we reserve the right to change the specification of any prod uct without prior notice. -
Page 4: Safety
17 The machine shall at all times be operated in accordance with relevant Health and Safety legislation. In the UK the " H ealth & Safety ® at Work Act 1974" applies. Any question regarding the correct operation of the machine must be directed to Avdel CAUTIONS AVDEL RECOMMENDS THAT ONLY HYDRAPAC UNITS BE USED TO DRIVE INSTALLATION TOOLS, AS OTHER MAKES OF HYDRAULIC POWER UNITS MAY NOT OPERATE AT THE SAFE DESIGNED WORKING PRESSURES. -
Page 5: Specifications Specifications
S p e c i f i c a t i o n s I n t e n t o f U s e The T40 Installation Tool is basically a Piston and Cylinder Assembly. When coupled Hydraulically and Electrically to a compati ®... -
Page 6: Putting Into Service
P r i n c i p l e o f O p e r a t i o n IMPORTANT Read the safety rules on page 4 carefully P r e p a r a t i o n f o r U s e •... -
Page 7: Operating Instructions
O p e r a t i n g I n s t r u c t i o n s ® To install a Avdelok Fastener • Check work and remove excessive gap. (Gap is the space between components of the Joint. Gap is excessive if not enough pintai sticks through the collar for the nose assembly j a ws to grab onto.) •... -
Page 8: Maintenance
M a i n t e n a n c e D i s m a n t l i n g I n s t r u c t i o n s IMPORTANT Be sure the HydraPac is turned off before removing tool or nose. •... -
Page 9: To Bleed The Tool
M a i n t e n a n c e To B l e e d t h e To o l To Bleed the Tool: • Couple the short tool hoses directly onto a HydraPac or compatible hydraulic power source. Note: Do not use long extension hoses as these will prevent the air from escaping into the HydraPac. -
Page 11: Parts List For T40 Installation Tool 73414-02000
T40 INSTALLATION TOOL PARTS LIST ITEM PART Nº DESCRIPTION QTY SERVICE KIT T404 ANVIL RETAINER E2 2 2 BACK-UP RING R 2 2 2 'O ' R I N G T 4 0 3 F R O N T G L A N D E 1 2 3 B A C K - U P R I N G R 1 2 3... -
Page 12: Servicing The Tool
S e r v i c i n g t h e To o l D a i l y We e k l y E v e r y 1 2 0 0 w o r k i n g h o u r s ( a t l e a s t o n c e a y e a r ) S e r v i c e To o l s H y d r a u l i c O i l G e n e r a l S a f e t y D a t a First Aid... -
Page 13: Fault Diagnosis
F a u l t D i a g n o s i s S y m p t o m P o s s i b l e C a u s e R e m e d y P a g e R e f... - Page 14 S y m p t o m P o s s i b l e C a u s e R e m e d y P a g e R e f...
- Page 15 Model: 73414-02000 Serial No..........to which this declaration relates is in conformity with the following standards: EN ISO 12100 - parts 1 & 2 BS EN ISO 8662 - part 6 BS EN ISO 11202 BS EN ISO 3744...
- Page 16 03/11 www.avdel-global.com www.infastech.com Autosert ¨ (eq u ipment), Avbolt ¨ , Avdel ¨ , Avdelmate ¨ , Avdel TX 2 0 00 ¨ , Avdelok ¨ , Avex ¨ , Avibulb ¨ , Avinox ¨ , Avinutª , Avlu g ¨...
Need help?
Do you have a question about the 73414-02000 and is the answer not in the manual?
Questions and answers