To get the most out of this manual, you should have an understanding of Ethernet networking concepts. In this manual, you will find: · Features on the switch · Illustrative LED functions · Installation instructions · Specifications IES-0820 User Manual Page 1...
When you unpack the product package, you shall find the items listed below. Please inspect the contents, and report any apparent damage or missing items immediately to your authorized reseller. · IES-0820 · Quick Installation Guide CD User Manual · IES-0820 User Manual Page 3...
· -40℃ to 75℃ (-40℉ to 167℉) operating temperature range. Tested for functional operation @ -40℃ to 85℃ (-40℉ to 185℉). UL1604 Industrial Control Equipment certified Maximum Surrounding Air Temperature @ 74℃ (165℉). · Supports DIN-Rail or Panel Mounting installation. IES-0820 User Manual Page 4...
· Port failure is not occurred · Port Fault Alarm is disabled 10/100Base-TX or 100Base-FX/BX Steady Network connection is established LNK/ACT (Green) Flashing Transmitting or Receiving data Steady Connection at 100Mbps speed (Yellow) Connection at 10Mbps speed IES-0820 User Manual Page 5...
Eight 10/100Base-TX ports + one 100Base-FX/BX port Six 10/100Base-TX ports + two 100Base-FX/BX ports Four 10/100Base-TX ports + four 100Base-FX/BX ports Connectivity RJ-45 connectors SC or ST connector on 100Base-FX fiber port SC connector on 100Base-BX fiber port IES-0820 User Manual Page 6...
· Surrounding electrical devices should not exceed the electromagnetic field (RFC) standards. · Make sure that the switch receives adequate ventilation. Do not block the ventilation holes on each side of the switch · The power outlet should be within 1.8 meters of the switch. IES-0820 User Manual Page 7...
Installation: Place the switch on the DIN rail from above using the slot. Push the front of the switch toward the mounting surface until it audibly snaps into place. Removal: Pull out the lower edge and then remove the switch from the DIN rail. IES-0820 User Manual Page 8...
Power Ground Earth Ground Relay Output 1A @ 24VDC 1. The relay contact opens if Power1 or Power2 falls 2. The relay contact opens if the Port Link is broken (When Link Down Detection is enabled) IES-0820 User Manual Page 9...
Page 11
Step 2: Connect the power cord to the AC to DC power adapter and attach the plug into a standard AC outlet with the appropriate AC voltage. DC Jack 12VDC Input Relay Output 1A @ 24VDC 1. The relay contact close if power falls IES-0820 User Manual Page 10...
Special note: The relay output is normal open position when there is no power to the switch. Please do not connect any power source to this terminal to prevent the shortage to your power supply. IES-0820 User Manual Page 11...
Connect one end of the cable to the switch and the other end to a desired device. Step 5: Once the connections between two end devices are made successfully, turn on the power and the switch is operational. IES-0820 User Manual Page 12...
Storage Temperature -45℃ to 85℃ (-40℉ to 185℉) Humidity 5%-95% non-condensing Safety Hazardous location: Class I, Division 2 group A, B, C & D UL60950-1, EN60950-1, IEC60950-1 FCC Part 15, Class A EN61000-6-3: EN55022, EN61000-3-2, EN61000-3-3 IES-0820 User Manual Page 13...
Page 15
EN61000-4-4 (Burst Standards) EN61000-4-5 (Surge Standards) EN61000-4-6 (Induced RFI Standards) EN61000-4-8 (Magnetic Field Standards) Environmental Test Compliance IEC60068-2-6 Fc (Vibration Resistance) IEC60068-2-27 Ea (Shock) IEC60068-2-32 Ed (Free Fall) NEMA TS1/2 Environmental requirements for traffic control equipment IES-0820 User Manual Page 14...
Standard Port Uplink Port Output Transmit Data + Input Receive Data + Output Transmit Data - Input Receive Data - Input Receive Data + Output Transmit Data + Input Receive Data - Output Transmit Data - IES-0820 User Manual Page 15...