Related Manuals for ESP PTZ10EXT
Summary of Contents for ESP PTZ10EXT
- Page 1 PTZ1 EXT E X T E R N A L PA N , T I LT A N D Z O O M D O M E C A M E R A U S E R M A N U A L...
-
Page 2: Product Overview
Product Overview FEATURES • 10x optical zoom • IR Night vision up to 50m • 360 degree endless pan rotation • Auto flip function to aid tracking of subjects beneath camera • Control protocol auto-detect • Supports Pelco D/P, Hik and Dahua control protocols •... -
Page 3: Maintenance
Pre-Installation Guidance SITING YOUR PTZ CAMERA Do not install your PTZ camera in any of the following locations: • In areas where humidity reaches >90% • Near a boiler flue or air conditioning outlet. • In environments high in smoke or dust. Avoid directing the camera towards very strong light sources such as the sun. -
Page 4: Installation
Installation 1. Mark out the holes for the 4 fixing 2. Drill holes and insert rawl plugs screws using template provided 3. Remove cover to access address/baud 4. Replace cover and screw rate/resistor switches (see page 5) M4 SCREW 5. Thread cables through the bracket 6. -
Page 5: Configuration Dip Switches
Configuration DIP Switches SWITCH SW1 CAMERA ID/ ADDRESS SETUP (SWITCH SW1) PTZ cameras must be addressed with a unique number. This number can be from 0-255 and is set in binary, use the table below to manually set the address. SWITCH SW2 Visit http://www.binaryhexconverter.com for more help to convert decimal to binary. -
Page 6: Connecting Multiple Ptz Cameras
Connections Using a screened control cable is recommended for maximum protection against interference. 12V/DC Connect to power supply, connect 230V mains supply to power supply RS485A(+) Connect to PTZ controller (or DVR) RS485A+ RS485B(-) Connect to PTZ Controller (or DVR) RS485B- Earth wire Connect to control cable screen. -
Page 7: Basic Operation
Basic Operation SET/RECALL PRESET POSITIONS 1. Set PTZ controller to the correct PTZ camera (input PTZ ID, press CAM) 2. Use joystick to position/zoom camera to chosen position 3. Input (position number), + PRESET To recall a preset position, input (position number) +SHOT PRESET FUNCTION ACCESS Some of the commonly used functions on the PTZ camera can be accessed by entering certain preset numbers. -
Page 8: Osd Menu Overview
OSD Menu Overview... -
Page 9: System Information
OSD Menu Features MAIN MENU System Information Display system information Display Setting Configuration of on-screen information System Setting Configuration of system parameters IR LED Setting Configuration of IR illumination parameters Restart Camera Restart the zoom module Reset Revert to factory default settings SYSTEM INFORMATION Protocol Set control protocol to Pelco/Hik/Auto... -
Page 10: System Setting Menu
System Setting Menu Camera Options for OSD screen tips, focus and zoom functions Movement Control Options for movement speed, orientation, scanning and movement limits Preset Configure preset positions Patrol Track Configure patrol tracks Pattern Configure patrol patterns Remove Remove presets, patrols or patterns Exit Leave OSD menu CAMERA... - Page 11 PRESET (Preset camera positions) Number Select preset to be edited (0-220) Label Set name of preset (not available) Edit Position camera/zoom to set preset position Remove Delete current preset PATROL TRACK (A group of sequenced preset positions) Number Select patrol track to be edited Edit Create or edit a patrol track, Preset = preset no, Speed = panning speed, Time = dwell time...
-
Page 12: Technical Specifications
Technical Specifications Rated Voltage 12V DC Max current 1.25A IR effective distance Protection IP66 Pan rotation 360° Endless rotation Speed Pan 0.6-200°/s Tilt 3.5-30°/s Working conditions -10°C - +50°C Elite Security Products Telephone: 01527 51 51 50 Unit 7, Target Park, Shawbank Rd Fax: 01527 51 51 43 Lakeside, Redditch B98 8YN email: info@espuk.com...