Summary of Contents for Chrysler 2016 Town & Country
Page 1
Town & Country 2 0 1 6 O W N E R ’ S M A N U A L I n f o r ma t i o n P r o v i d e d b y :...
Page 2
VEHICLES SOLD IN CANADA This manual illustrates and describes the operation of With respect to any Vehicles Sold in Canada, the name FCA features and equipment that are either standard or op- US LLC shall be deemed to be deleted and the name FCA tional on this vehicle.
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained tech- Congratulations on selecting your new FCA US LLC nicians and genuine MOPAR® parts, and cares about vehicle. Be assured that it represents precision workman- your satisfaction.
Page 7
INTRODUCTION 5 I n f o r ma t i o n P r o v i d e d b y :...
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in a collision, bodily injury and/or death. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped VIN Location NOTE: It is illegal to remove or alter the VIN. I n f o r ma t i o n P r o v i d e d b y :...
Page 10
I n f o r ma t i o n P r o v i d e d b y :...
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS When released from the START position, the switch automatically returns to the ON/RUN position. Your vehicle is equipped with a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch.
Page 15
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. Insert the square end of the Key Fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Power window switches will also remain active for up to 10 minutes after the ignition switch has been turned to OFF, depending upon the accessory delay setting. Opening either front door will cancel this feature. WARNING! •...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 WARNING! (Continued) CAUTION! • Never leave children alone in a vehicle, or with An unlocked vehicle is an invitation to thieves. access to an unlocked vehicle. Always remove the Key Fob from the ignition and •...
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE will cause the reminder chime to sound. Refer to “Start- After turning the ignition switch to the ON/RUN posi- ing Procedures” in “Starting And Operating” for further tion, the Vehicle Security Light will turn on for three information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Duplication of Key Fobs may be performed at an autho- CAUTION! (Continued) rized dealer, this procedure consists of programming a Use of these systems may result in vehicle starting blank Key Fob to the vehicle electronics. A blank Key Fob problems and loss of security protection.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. This device may not cause harmful interference, and flash repeatedly, and the horn will sound. For an addi- tional 15-minutes, only the headlights, park lamps 2. This device must accept any interference received, and/or turn signals and Vehicle Security Light will flash.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 • For vehicles not equipped with Keyless Enter-N-Go, To Disarm The System make sure the vehicle ignition system is OFF, and the The Vehicle Security Alarm can be disarmed using any of key is physically removed from the ignition.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, • The driver’s door key cylinder and the liftgate button disarm the Vehicle Security Alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 ILLUMINATED APPROACH The illuminated entry system will not operate if the dimmer control is in the “Dome OFF” position (rotate The courtesy lights will turn on when you use the horizontal thumb wheel on the bottom of the switch to Remote Keyless Entry (RKE) transmitter to unlock the the far left detent position).
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE using a hand-held Key Fob with RKE transmitter. The RKE transmitter does not need to be pointed at the vehicle to activate the system. NOTE: Inserting the Key Fob with RKE transmitter into the ignition switch disables the system from responding to any button pushed from that RKE transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 (optional). Some features can be programmed to the Remote Unlock Doors And Liftgate customers preferences. For example, flash headlights or Push and release the UNLOCK button on the RKE sound horn on LOCK. transmitter once to unlock the driver’s side or twice to unlock all doors and liftgate.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, the Remote NOTE: Pushing the LOCK button on the RKE transmit- Unlock feature can be enabled or disabled by perform- ter while you are inside the vehicle will activate the ing the following steps: Vehicle Security Alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 • For vehicles not equipped with the EVIC, perform the NOTE: Pushing the LOCK button on the RKE transmit- following steps: ter while you are in the vehicle will activate the Vehicle Security Alarm.
Page 28
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If equipped with a rear interior switch on the left rear pillar, pushing this switch once will close the liftgate only. • When you turn off the Panic Alarm by pushing the The liftgate cannot be opened from this switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 If the vehicle is locked and the Vehicle Security Alarm is Turn Off Flash Lights With RKE Lock — If armed, pushing the LEFT Power Sliding Door button Equipped twice unlocks the power sliding door and disarms Ve- This feature will cause the turn signal lights to flash when hicle Security Alarm.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Push and hold the UNLOCK button on a programmed Programming Additional Transmitters RKE transmitter for at least 4 seconds, but no longer If you do not have a programmed RKE transmitter, than 10 seconds.
Page 31
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 Emergency Key Removal Inserting Key Into Transmitter Case Slot 2. Insert the tip of the emergency key or a #2 flat blade screwdriver into the slot and gently pry the two halves of the RKE transmitter apart.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. To assemble the RKE transmitter case, snap the two halves together. General Information The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle: This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s).
Page 33
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 • Hood closed REMOTE STARTING SYSTEM — IF EQUIPPED • Liftgate closed This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conve- • Hazard switch off niently from outside the vehicle while still •...
Page 34
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Remote Start Aborted — Hood Ajar WARNING! • Remote Start Aborted — Liftgate Ajar • Do not start or run an engine in a closed garage or • Remote Start Aborted — Fuel Low confined area.
Page 35
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 NOTE: UNLOCK button on the RKE transmitter. After the vehicle is unlocked, you can enter the vehicle, push and • If your power door locks were unlocked, Remote Start release the START/STOP button (or insert the Key Fob will automatically lock the doors.
Page 36
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles equipped with the Keyless Enter-N-Go NOTE: feature, the message “Remote Start Active — Push • For vehicles equipped with the Electronic Vehicle Start Button” will display in the EVIC until you push Information Center (EVIC), the message “Insert Key/ the START/STOP button.
Page 37
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 • The engine is allowed to run for the entire 15-minute button was pushed, the vehicle must be reset by cycling cycle. the START/STOP button to the ON/RUN position. To Turn Off The Engine While In Remote Start General Information Mode The following regulatory statement applies to all Radio...
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS Manual Door Locks Lock the front doors by pushing down on the lock knobs on each door trim panel. If the lock knob is down when you shut either front door, the door will lock.
Page 39
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! (Continued) • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. •...
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not leave the Key Fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go in the ACC or ON/RUN mode.
Page 41
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 operate. A chime will sound if the Key Fob is in the If you push the power door lock switch while the sliding ignition switch and a door is open, as a reminder to door is open, the sliding door will lock.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Unlock Doors Automatically On Exit feature will not NOTE: operate if there is any manual operation of the power • Passive Entry may be programmed ON/OFF. Refer to door locks (lock or unlock). “Electronic Vehicle Information Center (EVIC)/ On vehicles equipped with the optional Electronic Ve- Personal...
Page 43
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 • If the vehicle is unlocked by Passive Entry and no door is opened within 60 seconds, the vehicle will re-lock and if equipped will arm the security alarm. To Unlock From The Driver’s Side: With a valid Passive Entry RKE transmitter within 5 ft (1.5 m) of the driver’s door handle, grab the driver’s front door handle to unlock the vehicles door’s automatically.
Page 44
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If “Unlock All Doors 1st Press” is programmed, Preventing Inadvertent Locking Of Passive Entry RKE all doors will unlock when you grab hold of the driver’s Transmitter In Vehicle front door handle. To select between “Unlock Driver To minimize the possibility of unintentionally locking a Door 1st Press”...
Page 45
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 NOTE:On the third attempt ALL doors will lock and the Passive Entry RKE transmitter can be locked in the vehicle. To Enter The Liftgate With a valid Passive Entry RKE transmitter within 5 ft (1.5 m) of the liftgate, cycle the handle to open the liftgate and pull the liftgate open with one fluid motion.
Page 46
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Do NOT grab the door handle, when pushing the door NOTE: handle button. This could unlock the door(s). • After pushing the door handle button, you must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
Page 48
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Window Lockout Switch — If Equipped The driver may lock out the rear power windows by pushing the bar switch just below the power window switches. Driver’s Power Window Switches NOTE: Power Window switches will also remain active for up to 10 minutes after the ignition switch has been turned to OFF, depending upon the accessory delay setting.
Page 49
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Front Passenger Power Window Switch There is a single switch on the front passenger’s door trim panel which operates the passenger door window and a set of switches that lock and unlock all doors. The switches will operate only when the ignition switch is in the ON/RUN or ACC position and during power acces- sory delay.
Page 50
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto-Down Feature — If Equipped Auto Up Feature With Anti-Pinch Protection — If Equipped The front window switches may be equipped with an Auto-Down feature. Push the window switch past the The front driver and front passenger switches may be detent, release, and the window will go down automati- equipped with an Auto Up feature.
Page 51
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 NOTE: Auto Up Reset — If Equipped • If the window runs into any obstacle during auto- To reactivate the Auto Up feature, perform the following steps after vehicle power is restored: closure, it will reverse direction and then go back down.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The switches will operate only when the ignition switch NOTE: The sliding door windows do not fully open, is in the ON/RUN or ACC position and during power stopping several inches above the window sill. accessory delay.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 rocking forward and back. Rocking the handle back- Always make sure that the sliding door is fully latched wards opens the door and rocking forward releases the anytime the vehicle is in motion. hold open latch in order to close the door.
Page 54
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pulling the outside power sliding door handle a second time while the sliding door is power opening or power closing will allow the sliding door to be opened or closed manually. Push the button on the RKE transmitter twice within five seconds to open a power sliding door.
Page 55
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 master lock button, located in the overhead console, to door switch is pushed. To close the door, wait until it disable the switches and handles for the rear seat is fully open and then push the switch again. passengers.
Page 56
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Sliding Side Door Open Flash You can turn the feature back on by repeating the previous procedure. The left and right exterior hazard lights will flash for 12 seconds when either sliding door is opened. This will Power Sliding Side Door Power Switch alert other drivers in the area that passenger(s) could be To provide a safer environment for small children riding...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Sliding Side Door Child Protection Lock To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a Child Protection Door Lock system. NOTE: When the Child Protection Door Lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.
Page 58
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Slide the Child Protection Door Lock control inward NOTE: (toward the vehicle) to engage the Child Protection • After engaging the Child Protection Door Lock, always Door Lock. test the door from the inside to make certain it is in the desired position.
Page 59
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 NOTE: WARNING! • After setting the Child Protection Door Lock system, Avoid trapping anyone in the vehicle in a collision. always test the door from the inside to make certain it Remember that the sliding doors can only be opened is in the desired position.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE On vehicles equipped with power locks, the liftgate can be unlocked using the Remote Keyless Entry (RKE) transmitter button, or by activating the power door lock switches located on the front doors. To open the liftgate, push the liftgate release handle located on the underside of the license plate bar and pull the liftgate open with one fluid motion.
Page 61
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 seconds, to open the power liftgate. When the liftgate is fully open, pushing the button twice within five seconds, a second time, will close the liftgate. The power liftgate may also be opened and closed by pushing the button located on the overhead console.
Page 62
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power liftgate may be closed by pushing the button, and several audible beeps will occur to signal that the located in the upper left trim in the liftgate opening. liftgate is opening or closing. Pushing once will only close the liftgate.
Page 63
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 • During power operation, whether liftgate is fully open (62°C). Be sure to remove any buildup of snow or ice or fully closed, the liftgate chime will beep several from the liftgate before pushing any of the power times indicating power operation is in progress.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINT SYSTEMS WARNING! Some of the most important safety features in your • Driving with the liftgate open can allow poisonous vehicle are the restraint systems: exhaust gases into your vehicle. You and your •...
Page 65
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Here are some simple steps you can take to minimize the 5. You should read the instructions provided with your risk of harm from a deploying air bag: child restraint to make sure that you are using it properly.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ejection and the risk of injury caused by striking the WARNING! inside of the vehicle. Everyone in a motor vehicle should • Never place a rear-facing child restraint in front of be belted at all times. an air bag.
Page 67
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 position the Seat Belt Reminder Light will turn on and Change Of Status remain on until both outboard front seat belts are buckled. If the driver or outboard front seat passenger (if The outboard front passenger seat BeltAlert is not active equipped with outboard front passenger seat BeltAlert) when an outboard front passenger seat is unoccupied.
Page 68
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If BeltAlert has been deactivated and the driver WARNING! or outboard front seat passenger (if equipped with out- • Relying on the air bags alone could lead to more board front passenger seat BeltAlert) is unbuckled the Seat Belt Reminder Light will turn on and remain on until severe injuries in a collision.
Page 69
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 WARNING! (Continued) WARNING! (Continued) • Do not allow people to ride in any area of your • A lap belt worn too high can increase the risk of vehicle that is not equipped with seats and seat injury in a collision.
Page 70
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • A seat belt that is too loose will not protect you • A frayed or torn seat belt could rip apart in a properly. In a sudden stop, you could move too far collision and leave you with no protection.
Page 71
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Pulling Out The Latch Plate Inserting Latch Plate Into Buckle 3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” I n f o r ma t i o n P r o v i d e d b y :...
Page 72
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt so that it is snug and lies low 5. Position the shoulder belt across the shoulder and across your hips, below your abdomen. To remove chest with minimal, if any slack so that it is comfort- slack in the lap belt portion, pull up on the shoulder able and not resting on your neck.
Page 73
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.
Page 74
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The adjustable upper shoulder belt anchorage is 1. Remove the mini-latch plate and regular latch plate equipped with an Easy Up feature. This feature allows from its stowed position in the headliner slightly the shoulder belt anchorage to be adjusted in the upward behind the third row seat.
Page 75
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 2. Grasp the mini-latch plate and pull the seat belt over 3. Route the shoulder belt to the inside of the left head the seat. restraint. Mini-Latch Stowage Mini-Latch And Buckle Connected I n f o r ma t i o n P r o v i d e d b y :...
Page 76
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. When the seat belt is long enough to fit, insert the 5. Sit back in seat. Slide the regular latch plate up the mini-latch plate into the mini-buckle until you hear a webbing as far as necessary to allow the seat belt to go “click.”...
Page 77
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 6. When the seat belt is long enough to fit, insert the latch belt. To loosen the lap belt if it is too tight, pull on the plate into the buckle until you hear a “click.” lap belt.
Page 78
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Extender. The Seat Belt Extender should be used WARNING! only if the existing seat belt is not long enough. When the • If the mini-latch plate and mini-buckle are not Seat Belt Extender is not required for a different occu- pant, it must be removed.
Page 79
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Seat Belts And Pregnant Women Position the lap belt snug and low below the abdomen and across the strong bones of the hips. Place the shoulder belt across the chest and away from the neck. Never place the shoulder belt behind the back or under the arm.
Page 80
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The pretensioners are triggered by the Occupant Re- Restraints” section of this manual. The table below straint Controller (ORC). Like the air bags, the preten- defines the type of feature for each seating position. sioners are single use items.
Page 81
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 sound as the seat belt retracts. Allow the webbing to retract completely in this case and then carefully pull out only the amount of webbing necessary to comfortably wrap around the occupant’s mid-section. Slide the latch plate into the buckle until you hear a click.
Page 82
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Disengage The Automatic Locking Mode WARNING! Unbuckle the combination lap/shoulder belt and allow it • Never place a rear-facing child restraint in front of to retract completely to disengage the Automatic Locking an air bag.
Page 83
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 the Active Head Restraints (AHR) to deploy. If a rear WARNING! (Continued) impact requires deployment, both the driver and front only used to install rear-facing or forward-facing passenger seat AHRs will be deployed. child restraints that have a harness for restraining When AHRs deploy during a rear impact, the front half the child.
Page 84
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • All occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
Page 85
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 US LLC dealer must reset the AHRs on the driver’s and WARNING! (Continued) front passenger’s seat before driving. Personally attempt- as loose cargo could contact the Active Head Re- ing to reset the AHRs may result in damage to the AHRs straint during sudden stops.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Supplemental Side Air Bags WARNING! • Supplemental Knee Air Bags Deployed AHRs are not able to best protect you in all • Front and Side Impact Sensors types of collisions. Have deployed AHRs reset by an authorized dealer immediately.
Page 87
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 WARNING! • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel.
Page 88
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Advanced Front Air Bag Features WARNING! The Advanced Front Air Bag system has multistage • No objects should be placed over or near the air bag driver and front passenger air bags. This system provides on the instrument panel or steering wheel, because output appropriate to the severity and type of collision as any such objects could cause harm if the vehicle is...
Page 89
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 Advanced Front Air Bag Operation Seat belts are necessary for your protection in all colli- sions, and also are needed to help keep you in position, Advanced Front Air Bags are designed to provide addi- away from an inflating air bag.
Page 90
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Knee Impact Bolsters Supplemental Driver Knee Air Bag The Knee Impact Bolsters help protect the knees of the This vehicle is equipped with a Supplemental Driver driver and front passenger, and position the front occu- Knee Air Bag mounted in the instrument panel below the pants for improved interaction with the Advanced Front steering column.
Page 91
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 through the seat seam into the space between the occupant and the door. The SAB moves at a very high speed and with such a high force that it could injure occupants if they are not seated properly, or if items are positioned in the area where the SAB inflates.
Page 92
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE injury reduction potential provided by the seat belts and body structure. The SABICs deploy downward, covering the side win- dows. An inflating SABIC pushes the outside edge of the trim out of the way and covers the window. The SABICs inflate with enough force to injure occupants if they are not belted and seated properly, or if items are positioned in the area where the SABICs inflate.
Page 93
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 based on the severity and type of collision. Vehicle WARNING! damage by itself is not a good indicator of whether or not • Do not stack luggage or other cargo up high Side Air Bags should have deployed.
Page 94
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE be properly restrained in a child restraint or booster seat Side Impacts that is appropriate for the size of the child. In side impacts, the side impact sensors aid the ORC in determining the appropriate response to impact events.
Page 95
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 Rollover Events If A Deployment Occurs The Advanced Front Air Bags are designed to deflate Side Air Bags are designed to activate in certain rollover immediately after deployment. events. The ORC determines whether the deployment of the Side Air Bags in a particular rollover event is appro- NOTE: Front and/or side air bags will not deploy in all priate, based on the severity and type of collision.
Page 96
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • As the air bags deflate, you may see some smoke-like WARNING! particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air Deployed air bags and seat belt pretensioners cannot bag inflation.
Page 97
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 on the nature of the event, the ORC will determine OFF. Carefully check the vehicle for fuel leaks in the whether to have the Enhanced Accident Response Sys- engine compartment and on the ground near the engine tem perform the following functions: compartment and fuel tank before resetting the system and starting the engine.
Page 98
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC contains a backup power supply system that free, if any of the following occurs, have an authorized may deploy the air bags even if the battery loses power or dealer service the air bag system immediately. it becomes disconnected prior to deployment.
Page 99
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 WARNING! WARNING! (Continued) wiring, including adding any kind of badges or Ignoring the Air Bag Warning Light in your instru- stickers to the steering wheel hub trim cover or the ment panel could mean you won’t have the air bags to upper right side of the instrument panel.
Page 100
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Whether or not the driver and passenger safety belts WARNING! (Continued) were buckled/fastened; authorized dealer. Only manufacturer approved • How far (if at all) the driver was depressing the seat accessories may be used. If it is necessary to accelerator and/or brake pedal;...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 In addition to the vehicle manufacturer, other parties, WARNING! such as law enforcement, that have the special equip- ment, can read the information if they have access to the In a collision, an unrestrained child can become a vehicle or the EDR.
Page 102
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Canadian residents should refer to Transport Canada’s Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety website for additional information: www.tc.gc.ca/eng/ Standards.
Page 103
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Larger Children Children who have out-grown their Belt Positioning Booster Seat and the vehicle forward-facing child restraint, but seat belt, seated in the rear seat of are too small to properly fit the the vehicle vehicle’s seat belt...
Page 104
102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! Do not install a rear-facing car seat using a rear support • Never place a rear-facing child restraint in front of leg in this vehicle. The floor of this vehicle is not an air bag.
Page 105
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 Older Children And Child Restraints WARNING! Children who are two years old or who have outgrown • Improper installation can lead to failure of an their rear-facing convertible child seat can ride forward- infant or child restraint.
Page 106
104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Is the lap part of the belt as low as possible, touching WARNING! (Continued) the child’s thighs and not their stomach? could strike the occupants or seatbacks and cause 5. Can the child stay seated like this for the whole trip? serious personal injury.
Page 107
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 Recommendations For Attaching Child Restraints Restraint Type Combined Use any attachment method shown with an “X” Below Weight of the LATCH – Seat Belt Only LATCH – Seat Belt + Top Child + Child Lower Anchors Lower Anchors Tether Anchor...
Page 108
106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors And Tethers For CHildren seating position. These anchorages are used to install (LATCH) Restraint System LATCH-equipped child seats without using the vehicle’s seat belts. Some seating positions may have a top tether anchorage but no lower anchorages.
Page 109
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 107 LATCH Positions For Installing Child Restraints In This Vehicle Second Row Bench • Lower Anchorage Symbol 2 anchorages per seating position Second Row Captains Chairs • Top Tether Anchorage Symbol I n f o r ma t i o n P r o v i d e d b y :...
Page 110
108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Frequently Asked Questions About Installing Child Restraints With LATCH What is the weight limit (child’s weight + 65 lbs (29.5 kg) Use the LATCH anchorage system until weight of the child restraint) for using the the combined weight of the child and the LATCH anchorage system to attach the child restraint is 65 lbs (29.5 kg).
Page 111
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 109 Frequently Asked Questions About Installing Child Restraints With LATCH Can the rear-facing child restraint touch The child seat may touch the back of the the back of the front passenger seat? front passenger seat if the child restraint manufacturer also allows contact.
Page 112
110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion.
Page 113
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 111 third row center seating position. The tether anchorages are located on the back of the seat, near the floor. LATCH Anchorages (Third Row 60/40 Anchorages Shown) Locating Tether Anchorages Tether Strap Anchorages (Third Row 60/40 Anchorage Shown) There are tether strap anchorages located be- LATCH-compatible child restraint systems will be...
Page 114
112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE anchorage and a way to tighten the connection to the WARNING! anchorage. Forward-facing child restraints and some rear-facing child restraints will also be equipped with a Never use the same lower anchorage to attach more tether strap.
Page 115
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 113 1. Loosen the adjusters on the lower straps and on the 4. If the child restraint has a tether strap, connect it to the tether strap of the child seat so that you can more top tether anchorage.
Page 116
114 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Stow An Unused ALR Seat Belt: WARNING! When using the LATCH attaching system to install a • Improper installation of a child restraint to the child restraint, stow all ALR seat belts that are not being LATCH anchorages can lead to failure of the re- used by other occupants or being used to secure child straint.
Page 117
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 115 Installing Child Restraints Using The Vehicle Seat webbing out of the retractor and then letting the webbing Belt retract back into the retractor. If it is locked, the ALR will make a clicking noise while the webbing is pulled back The seat belts in the passenger seating positions are into the retractor.
Page 118
116 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle Second Row Bench • Cinch = Cinching Latch Plate • ALR = Switchable Automatic Locking Retractor Second Row Captains Chair I n f o r ma t i o n P r o v i d e d b y :...
Page 119
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 117 Lap/Shoulder Belt Systems Frequently Asked Question About Installing Child Restraints With Seat Belts What is the weight limit (child’s weight Weight limit of the Always use the tether anchor when using the + weight of the child restraint) for using seat belt to install a forward facing child re- Child Restraint...
Page 120
118 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing A Child Restraint With A Switchable 5. To lock the seat belt, pull down on the shoulder part of Automatic Locking Retractor (ALR) the belt until you have pulled all the seat belt webbing out of the retractor.
Page 121
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 119 strap. See the section “Installing Child Restraints rear-most position to make room for the child seat. Using the Top Tether Anchorage” for directions to You may also move the front seat forward to allow attach a tether anchor.
Page 122
120 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE strap. See the section “Installing Child Restraints If the belt still cannot be tightened after you shorten the Using the Top Tether Anchorage” for directions to buckle, disconnect the latch plate from the buckle, turn attach a tether anchor.
Page 123
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 121 2. Route the tether strap to provide the most direct path WARNING! (Continued) for the strap between the anchor and the child seat. If (LATCH) Restraint System” for the location of ap- your vehicle is equipped with adjustable rear head proved tether anchorages in your vehicle.
Page 124
122 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Rear Seat Tether Strap Mounting (Second Row Tether Strap Anchorages (Third Row 60/40 Anchorage Anchorage Shown) Shown) I n f o r ma t i o n P r o v i d e d b y :...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 123 ENGINE BREAK-IN RECOMMENDATIONS WARNING! A long break-in period is not required for the engine and • An incorrectly anchored tether strap could lead to drivetrain (transmission and axle) in your vehicle. increased head motion and possible injury to the Drive moderately during the first 300 miles (500 km).
124 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! WARNING! • Do not leave children or animals inside parked Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. vehicles in hot weather. Interior heat build-up may cause serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 125 Exhaust Gas WARNING! (Continued) • If it is necessary to sit in a parked vehicle with the WARNING! engine running, adjust your heating or cooling Exhaust gases can injure or kill. They contain carbon controls to force outside air into the vehicle.
126 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The have the system inspected at an authorized dealer as Vehicle soon as possible. This light will illuminate with a single chime when a fault with the Air Bag Warning Seat Belts Light has been detected, it will stay on until the fault Inspect the seat belt system periodically, checking for...
Page 129
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 127 unobstructed and that are firmly secured so that they WARNING! (Continued) cannot slip out of position and interfere with the pedals mats and other coverings will reduce the size of the or impair safe operation of your vehicle in other ways. pedal area and interfere with the pedals.
128 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside Door Latches The Vehicle Check for proper closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, patterns.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS ▫ Tilt Mirrors In Reverse (Available With Memory MIRRORS ......136 Seat Only) —...
Page 132
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Power Seats — If Equipped ....188 UCONNECT PHONE — IF EQUIPPED ..151 ▫ Operation ......153 ▫...
Page 133
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 ▫ Plastic Grocery Bag Retainer Hooks..219 ▫ Lights-On Reminder ....227 ▫...
Page 134
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Windshield Wiper Operation ... . .235 ▫ To Resume Speed .....244 ▫...
Page 135
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 ▫ Using HomeLink .....268 PARKVIEW REAR BACK UP CAMERA — IF EQUIPPED ......255 ▫...
Page 136
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Sunroof Maintenance ....273 ▫ Door Trim Panel Storage ....285 ▫...
Page 137
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 REAR WINDOW FEATURES ....298 ROOF LUGGAGE RACK — IF EQUIPPED ..299 ▫ Rear Window Defroster ....298 ▫...
Page 138
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
Page 139
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 NOTE: This feature is disabled when the vehicle is CAUTION! moving in reverse. To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
Page 140
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Full rearward position WARNING! (Continued) • Normal position other object. Use your inside mirror when judging the size or distance of a vehicle seen in a side convex Power Mirrors — If Equipped mirror.
Page 141
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 The power mirror controls consist of mirror select but- Heated Mirrors — If Equipped tons and a four-way mirror control switch. To adjust a These mirrors are heated to melt frost or ice. This mirror, push either the L (left) or R (right) to select the feature can be activated whenever you turn on the mirror that you want to adjust.
Page 142
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Tilt Mirrors in Reverse feature is not enabled when delivered from the factory. The Tilt Mirrors in Reverse feature can be enabled or disabled in the Elec- tronic Vehicle Information Center (EVIC). Refer to “Elec- tronic Vehicle Information Center (EVIC)”...
Page 143
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Resetting The Power Folding Outside Mirrors Illuminated Vanity Mirrors — If Equipped You may need to reset the power folding mirrors if the An illuminated vanity mirror is located on the sun visor. following occurs: To use the mirror, rotate the sun visor down and swing the mirror cover upward.
Page 144
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE BLIND SPOT MONITORING (BSM) — IF EQUIPPED The Blind Spot Monitoring (BSM) system uses two radar- based sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.) that enter the blind spot zones from the rear/front/side of the vehicle.
Page 145
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 both sides of the vehicle when the vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas. NOTE: • The BSM system does NOT alert the driver about rapidly approaching vehicles that are outside the de- tection zones.
Page 146
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE contamination so that the BSM system can function properly. Do not block the area of the rear fascia where the radar sensors are located with foreign objects (bum- per stickers, bicycle racks, etc.). The BSM system notifies the driver of objects in the detection zones by illuminating the BSM warning light located in the outside mirrors in addition to sounding an...
Page 147
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 light will be illuminated. If the difference in speed between the two vehicles is greater than 15 mph (24 km/h), the warning light will not illuminate. Rear Monitoring Overtaking Traffic If you pass another vehicle slowly (with a relative speed Overtaking/Approaching of less than 15 mph (24 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning...
Page 148
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in berms, etc.
Page 149
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 WARNING! (Continued) system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicle’s mirrors, glance over your shoulder, and use your turn signal before changing lanes.
Page 150
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When RCP is on and the vehicle is in REVERSE, the driver is alerted using both the visual and audible alarms, including reducing the radio volume.
Page 151
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Modes Of Operation Blind Spot Alert Lights/Chime Modes Of Operation With EVIC When operating in Blind Spot Alert Lights/Chime mode, the BSM system will provide a visual alert in the appro- Three selectable modes of operation are available in the priate side view mirror based on a detected object.
Page 152
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the system is in RCP, the system shall respond with General Information both visual and audible alerts when a detected object is This vehicle has systems that operate on radio frequency present. Whenever an audible alert is requested, the radio that comply with Part 15 of the Federal Communications volume is reduced.
Page 153
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 UCONNECT PHONE — IF EQUIPPED Uconnect Phone allows you to transfer calls between the system and your mobile phone as you enter or exit your Uconnect Phone is a voice-activated, hands-free, in- vehicle and enables you to mute the system’s microphone vehicle communications system.
Page 154
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Command Button WARNING! Actual button location may vary with the ra- Any voice commanded system should be used only dio. The individual buttons are described in the in safe driving conditions following all applicable “Operation”...
Page 155
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Operation part of the command when you are asked for it. For example, you can use the compound form voice com- Voice commands can be used to operate the Uconnect mand “Phonebook New Entry,” or you can break the Phone and to navigate through the Uconnect Phone compound form command into two voice commands: menu structure.
Page 156
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To activate the Uconnect Phone, simply push the Phone The following are general phone to Uconnect Phone button and follow the audible prompts for direc- pairing instructions: tions. Uconnect Phone sessions begin with a push of 1.
Page 157
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 • You will then be asked to give your mobile phone a Dial By Saying A Number priority level between one and seven, with one being To dial a number using Voice Command: the highest priority.
Page 158
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The system will prompt you to say the name of the • To call a name from the Uconnect Phonebook or person you want to call. downloaded Phonebook, follow the procedure in “Call by Saying a Name”...
Page 159
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 • Either the mobile phone’s phonebook or the mobile • Use of long names helps the Voice Command and is phone’s SIM card phonebook is downloaded. recommended. For example, say “Robert Smith” or “Robert”...
Page 160
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE only in that language. In addition, if equipped and 3. Select the number designation (home, work, mobile, supported by your phone, Uconnect Phone automatically or other) that you wish to edit. downloads your mobile phone’s phonebook. 4.
Page 161
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Delete Uconnect Phonebook Entry to delete. You can either say the name of a phonebook entry that you wish to delete or you can say “List NOTE: Names” to hear a list of the entries in the phonebook •...
Page 162
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Uconnect Phone will play the names of all the To delete or erase all Uconnect phonebook entries using Voice Command: phonebook entries, including the downloaded phonebook entries, if available. 1. Push the Phone button to begin.
Page 163
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 accessed through the Uconnect Phone. Check with your NOTE: The Uconnect Phone compatible phones in the mobile service provider for the features that you have. market today do not support rejecting an incoming call when another call is in progress.
Page 164
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Place/Retrieve A Call From Hold Conference Call To put a call on hold: When two calls are in progress (one active and one on hold): 1. Push the Phone button until you hear a single beep.
Page 165
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Call Termination NOTE: This may not be the last number dialed from the Uconnect Phone. To end a call in progress: Call Continuation 1. Momentarily push the Phone button. • Only the active call(s) will be terminated and if there Call continuation is the progression of a phone call on the Uconnect Phone after the vehicle ignition key has been is a call on hold, it will become the new active call.
Page 166
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • An active call is automatically transferred to the mo- NOTE: After every Uconnect Phone language change bile phone after the ignition key is cycled to OFF. operation, only the language-specific 32-name phone- book is usable.
Page 167
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 paired mobile phone to call the emergency number. WARNING! This feature is supported in the U.S., Canada, and Mexico. To use your Uconnect Phone System in an emergency, your mobile phone must be: NOTE: •...
Page 168
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: You should program the desired Towing Assis- Working With Automated Systems tance phone number using the Voice Command system. This method is used in instances where one generally has To do this, push the Phone button and say “Setup,”...
Page 169
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 • Some paging and voice mail systems have system time used for navigating through an automated customer service center menu structure, and to leave a number out settings that are too short and may not allow the on a pager.
Page 170
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the “Ready” prompt and the following beep, say dialing a number with your paired Bluetooth mobile one of the following: phone, the audio will be played through your vehicle’s audio system. The Uconnect Phone will work the same as –...
Page 171
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 • Following the beep, say “Mute.” Connect Or Disconnect Link Between The Uconnect Phone And Mobile Phone To un-mute the Uconnect Phone: Your mobile phone can be paired with many different • Push the Voice Command button.
Page 172
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Uconnect Phone will play the phone names of all The selected phone will be used for the next phone call. paired mobile phones in order from the highest to the If the selected phone is not available, the Uconnect Phone lowest priority.
Page 173
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 • Push the Voice Command Things You Should Know About Your Uconnect button and say the Phone “Voice Training,” “System Training,” or “Start Voice Training” command. Uconnect Phone Tutorial You can either push the Uconnect Phone button to restore To hear a brief tutorial of the system features, push the the factory setting or repeat the words and phrases when Phone...
Page 174
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • This will delete all phone pairing, phone book en- Performance is maximized under: tries, and other settings in all language modes. The • Low-to-medium blower setting System will prompt you before resetting to factory •...
Page 175
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 • Storing names in the phonebook when the vehicle is Far End Audio Performance not in motion is recommended. Audio quality is maximized under: • It is not recommended to store similar sounding names •...
Page 176
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In a convertible vehicle, system performance may be 2. After the “Ready” prompt and the following beep, say compromised with the convertible top down. “SMS Read” or “Read Messages.” • Uconnect Phone will play the new text message for Recent Calls you.
Page 177
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Uconnect Phone will prompt you to say the name or Turn SMS Incoming Announcement ON/OFF number of the person you wish to send the message to. Turning the SMS Incoming Announcement OFF will stop the system from announcing the new incoming messages.
Page 178
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE I n f o r ma t i o n P r o v i d e d b y :...
Page 179
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 I n f o r ma t i o n P r o v i d e d b y :...
Page 180
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE I n f o r ma t i o n P r o v i d e d b y :...
Page 181
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 Voice Commands Primary Alternate (s) Primary Alternate (s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
Page 182
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary Alternate (s) Primary Alternate (s) home redial language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
Page 183
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 General Information USB mass storage class device, iPod family of devices, Bluetooth Streaming Audio Device, satellite radio, and a This device complies with Part 15 of the FCC rules and memo recorder. RSS 210 of Industry Canada. Operation is subject to the following conditions: NOTE: Take care to speak into the Voice Interface System as calmly and normally as possible.
Page 184
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When you push the Voice Command button, you will These commands are universal and can be used from any hear a beep. The beep is your signal to give a com- menu. All other commands can be used depending upon mand.
Page 185
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Commands Main Menu The Voice Command system understands two types of Start a dialogue by pushing the Voice Command but- commands, Universal commands and Local commands. ton. You may say “Main Menu” to switch to the main Universal commands are available at all times.
Page 186
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “Menu Radio” (to switch to the radio menu) Radio AM • “Main Menu” (to switch to the main menu) To switch to the AM band, say “AM” or “Radio AM.” In this mode, you may say the following commands: Satellite Radio •...
Page 187
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 Disc Mode Bluetooth Streaming (BT) Mode To switch to the disc mode, say “Disc.” In this mode, you To switch to Bluetooth Streaming (BT) mode, say may say the following commands: “Bluetooth Streaming.” In this mode, you may say the following commands: •...
Page 188
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE – “Save” (to save the memo) Setup – “Continue” (to continue recording) To switch to system setup, you may say one of the following: – “Delete” (to delete the recording) • “Change to setup” •...
Page 189
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 NOTE: Keep in mind that you have to push the Voice blower fan switched off. This procedure may be re- peated with a new user. The system will adapt to the Command button first and wait for the beep before last trained voice only.
Page 190
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Be sure everyone in your vehicle is in a seat and using a seat belt properly. Power Seats — If Equipped Some models may be equipped with eight-way power seats for the driver and front passenger. The power seat switches are located on the outboard side of the seat.
Page 191
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 WARNING! CAUTION! • Adjusting a seat while driving may be dangerous. Do not place any article under a power seat or Moving a seat while driving could result in loss of impede its ability to move as it may cause damage to control which could cause a collision and serious the seat controls.
Page 192
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjusting The Seat Up Or Down WARNING! The height of the seats can be adjusted up or down. Pull • Adjusting a seat while driving may be dangerous. upward or push downward on the seat switch, the seat Moving a seat while driving could result in loss of will move in the direction of the switch.
Page 193
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.
Page 194
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vehicles Equipped With Remote Start WARNING! On models that are equipped with remote start, the • Persons who are unable to feel pain to the skin driver’s heated seat can be programmed through the because of advanced age, chronic illness, diabetes, Electronic Vehicle Information Center (EVIC) to come on spinal cord injury, medication, alcohol use, exhaus-...
Page 195
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 You can choose from HI, LO or OFF heat settings. Amber Rear Heated Seats indicator lights in each switch indicate the level of heat in On some models, the second row seats are equipped with use.
Page 196
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE You can choose from HI, LO or OFF heat settings. Amber Manual Front/Second Row Seat Adjuster indicator lights in each switch indicate the level of heat in Both front seats are adjustable forward or rearward. The use.
Page 197
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 have reached the desired position. Then, using body Manual Reclining Seats — If Equipped pressure, move forward and rearward on the seat to be For models equipped with manual reclining seats, the sure that the seat adjusters have latched. recline lever is located on the outboard side of the seat.
Page 198
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To recline, lean forward slightly, lift the lever, then push WARNING! back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its The head restraints for all occupants must be prop- normal position.
Page 199
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 When AHRs deploy during a rear impact, the front half of the head restraint extends forward to reduce the gap between the back of the occupant’s head and the AHR. This system is design to reduce the risk of injury to the driver or front passenger in certain types of rear impacts.
Page 200
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For comfort the Active Head Restraints can be tilted forward and rearward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head.
Page 201
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 • In the event of deployment of an Active Head Re- WARNING! (Continued) straint, refer to “Occupant Restraints/Resetting Active • Active Head Restraints may be deployed if they are Head Restraints (AHR)” in “Things To Know Before struck by an object such as a hand, foot or loose Starting Your Vehicle”...
Page 202
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Head Restraints — Second Row Quad Seats Head Restraints — Second Row Bench To raise the head restraint, pull upward on the head If your vehicle is equipped with a second row bench seat, restraint.
Page 203
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 Second Row Stow ’n Go On vehicles equipped with Stow ’n Go seats, the seats will fold and tumble in one motion. 1. Move the front seat fully forward. 2. Recline the front seatback fully forward. 3.
Page 204
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Pull upward on the seatback recliner lever located on The non-adjustable head restraint and seatback will fold the outboard side of the seat. automatically during the seat tumble. No additional actuation is necessary. Seatback Recliner Lever, Seat Tumble, And Head Restraint Fold Lever Non-Adjustable Head Restraint...
Page 205
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 The seat will automatically tumble into position for easy storage. Automatic Folding Seatback Tumbled Second Row Seat I n f o r ma t i o n P r o v i d e d b y :...
Page 206
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Push the seat into the storage bin. CAUTION! The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover. WARNING! In a collision, serious injury could result if the seat storage bin covers are not properly latched.
Page 207
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 To Unstow Second Row Seats WARNING! (Continued) 1. Pull up on the storage bin latch to open the cover. • Sitting in a seat with the head restraint in its lowered position could result in serious injury or 2.
Page 208
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Return the seatback to the upright position. 2. Return the head restraint to the upright position. Raising The Seatback Raising The Head Restraint I n f o r ma t i o n P r o v i d e d b y :...
Page 209
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 3. Pull up on the seatback recliner lever on the outboard side of the seat to fold head rest and seatback and tumble seat forward. Easy Entry Second Row The second row Stow ’n Go seats allow easy entry to the third row seat or rear cargo area.
Page 210
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In the event of a collision you could be injured if the seat is not fully latched. Quad Seats — If Equipped Both Quad seats are adjustable forward or rearward. The manual seat adjustment handle is located under the seat cushion at the front edge of each seat.
Page 211
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked.
Page 212
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fold-Flat Easy Entry To fold the seat, lift the recliner lever to the full upward The Quad seats can be tilted forward for easy entry into position and push the seatback forward until it rests on the third row.
Page 213
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 For passengers seated in the third row, there is a pull Removal strap located on the outboard side of the seat near the The Quad seats can be removed if additional storage is bottom of the seat back.
Page 214
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second Row Bench Seat — If Equipped Release levers are located on the rear leg assemblies, near the floor. To remove the seat, squeeze each release handle While the bench seat does not stow in the floor, it is and rotate downwards to deploy the wheels.
Page 215
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 To reinstall the seat, align the seat into the detent posi- tions on the floor. Squeeze the release handle and rotate upward until the lock indicator button returns into the handle. WARNING! If not properly latched, the bench seats could become loose.
Page 216
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Lower the head restraint by pulling on the release strap marked “1” located on the outboard side of the head restraint. One Touch Folding Seat Third Row The rear switch bank allows multiple power folding and unfolding positions for the third row seats.
Page 217
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 NOTE: • Disconnect the center shoulder belt from the small buckle and lower the head restraints before attempting to fold/stow the power third row seats. • To abort seat operation while seat is in motion, push a different seat position selector switch to stop the seat.
Page 218
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manually Folding Third Row Seats — If Equipped 1. Lower the center head restraint down to the seatback by pushing the button on the guide and pushing the head restraint down. 2. Lower the outboard head restraints by pulling on the release strap marked “1”...
Page 219
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 3. Pull release strap marked “2” located on the rear of the 4. Pull release strap marked “3” to release the anchors. seat to lower the seatback. Release Strap “3” Release Strap “2” I n f o r ma t i o n P r o v i d e d b y :...
Page 220
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Pull release strap marked “4” and tumble the seat rearward into the storage bin. Stowed Third Row Seat To Unfold Third Row Seats Release Strap “4” 1. Pull up on the assist strap to lift the seat out of the storage bin and push the seat forward until the anchors latch.
Page 221
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 3. Pulling strap “4” releases the seatback to return to its 2. To restore the seat to its upright position, lift up on the full upright position. seatback and push forward until the anchors latch. 4.
Page 222
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE equipped), and radio station preset settings. Your Remote Your vehicle may have been delivered with two RKE Keyless Entry (RKE) transmitters can also be pro- transmitters, one RKE transmitter can be linked to each of grammed to recall the same positions when the UN- the memory positions.
Page 223
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 4. Within five seconds, push and release either of the NOTE: Before programming your RKE transmitters you memory buttons (1) or (2). The Electronic Vehicle must select the “RKE Linked To Memory” feature Information Center (EVIC) will display which through the Electronic Vehicle Information Center memory position has been set.
Page 224
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Push and release button (1) or (2) accordingly. To recall the memory setting for driver two, push “Memory Profile Set” (1 or 2) will display in the MEMORY button 2 on the driver’s door or the UN- instrument cluster.
Page 225
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 • The Easy Entry/Easy Exit feature is disabled when the The distance the driver seat moves depends on where you have the driver seat positioned when you remove the driver seat position is less than 0.9 inches (22.7 mm) key from the ignition switch.
Page 226
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD 2. Move to the front of the vehicle and look inside the center of the hood opening. Locate, then push the To open the hood, two latches must be released. safety catch lever downward while raising the hood at 1.
Page 227
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 Use the hood prop rod to secure the hood in the open LIGHTS position. Headlight Switch The headlight switch is located on the left side of the CAUTION! instrument panel. The switch controls the operation of To prevent possible damage, do not slam the hood to the headlights, parking lights, instrument panel lights, close it.
Page 228
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rotate the headlight switch clockwise to the first detent Headlights On With Wipers — If Equipped for parking light and instrument panel light operation. When your headlights are in the AUTO mode and the Rotate the headlight switch to the second detent for engine is running, the headlights will automatically turn headlight, parking light and instrument panel operation.
Page 229
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 headlights within 45 seconds. The 90 second delay inter- Lights-On Reminder val begins when headlight switch is turned off. If the If the headlights or the parking lights are left on, or if the headlights or parking lights are turned back on or the dimmer control is in the extreme top position after the ignition switch is turned ON, the delay will be cancelled.
Page 230
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Fog Lights — If Equipped To activate the front fog lights, turn on the parking lights or the low beam headlights and push in the headlight switch control knob. Pushing the headlight switch control knob in a second time will turn the front fog lights off.
Page 231
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 Interior Lighting On NOTE: The ignition must be cycled to the OFF position for this feature to operate. Rotate the left dimmer control completely upward to the second detent (extreme top position) to turn on the Interior Lighting Off interior lights.
Page 232
230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multifunction Lever The multifunction lever is located on the left side of the steering column. Halo Control To activate the Halo lights, rotate the Halo switch control upward or downward to in- crease or decrease the lighting. Multifunction Lever The multifunction lever controls the: •...
Page 233
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 • Headlight Beams Low/High Turn Signal Warning • Flash-To-Pass If the vehicle electronics sense that the vehicle has traveled at over 18 mph (29 km/h) for about 1 mile • Front and Rear Wipers — Washer Functions (1.6 km) with the turn signals on, a chime will sound to alert the driver.
Page 234
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Flash-To-Pass To Activate You can signal another vehicle with your headlights by 1. Select “Automatic High Beams — ON” through the lightly pulling the multifunction lever toward you. This EVIC. Refer to “Electronic Vehicle Information Center will cause the headlights to turn on at high beam and (EVIC)/Customer-Programmable Features”...
Page 235
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 3. Push the multifunction lever away from you to switch 3. Rotate the headlight switch clockwise from the AUTO the headlights to the high beam position. Refer to to the on position. “Multifunction Lever” in this section for further infor- Battery Protection mation.
Page 236
234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPER AND WASHERS NOTE: Always remove any buildup of snow that pre- vents the windshield wiper blades from returning to the The wipers and washers are operated by a switch within off position. If the windshield wiper switch is turned off the multifunction lever.
Page 237
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 Intermittent Wiper System Windshield Washers Use the intermittent wiper when weather conditions To use the Washer, push on the end of the lever to the make a single wiping cycle with a variable pause be- second detent and hold while spray is desired.
Page 238
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Wiper And Washer The sensitivity of the system is adjustable from the multifunction lever. Wiper sensitivity position 3 has been Rotating the rotary ring to the first detent activates the calibrated for best overall wiping sensitivity. If the opera- rear intermittent wipers.
Page 239
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 • The Rain Sensing feature can be turned on and off • Neutral Wipe Inhibit — The Rain Sensing feature will through the EVIC (if equipped). Refer to “Electronic not operate when the ignition is ON, and the transmis- Vehicle Information Center (EVIC)/Personal Settings sion shift lever is in the NEUTRAL position, and the (Customer-Programmable Features)”...
Page 240
238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT/TELESCOPING STEERING COLUMN To unlock the steering column, push the lever downward (toward the floor). To tilt the steering column, move the This feature allows you to tilt the steering column steering wheel upward or downward as desired. To upward or downward.
Page 241
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 HEATED STEERING WHEEL — IF EQUIPPED NOTE: The engine must be running for the heated steering wheel to operate. Vehicles Equipped With Re- The steering wheel contains a heating element that helps mote Start warm your hands in cold weather.
Page 242
240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material. This may cause the steering wheel heater to overheat. ADJUSTABLE PEDALS —...
Page 243
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241 • The pedals cannot be adjusted when the vehicle is in positions. Refer to “Driver Memory Seat” in “Under- REVERSE or when the Electronic Speed Control Sys- standing The Features Of Your Vehicle” for further tem is on.
Page 244
242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, the Electronic Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h). The Electronic Speed Control buttons are located on the right side of the steering wheel.
Page 245
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 NOTE: In order to ensure proper operation, the Elec- WARNING! tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at Leaving the Electronic Speed Control system on the same time.
Page 246
244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate To Vary The Speed Setting A soft tap on the brake pedal, pushing the CANCEL To Increase Speed button, or normal brake pressure while slowing the When the Electronic Speed Control is set, you can in- vehicle will deactivate the Electronic Speed Control with- crease speed by pushing the RES (+) button.
Page 247
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 • If the button is continually pushed, the set speed will The speed decrement shown is dependant on the chosen continue to increase until the button is released, then speed unit of U.S. (mph) or Metric (km/h): the new set speed will be established.
Page 248
246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing WARNING! Press the accelerator as you would normally. When the Electronic Speed Control can be dangerous where the pedal is released, the vehicle will return to the set speed. system cannot maintain a constant speed.
Page 249
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 PARKSENSE REAR PARK ASSIST — IF ParkSense Sensors EQUIPPED The four ParkSense sensors, located in the rear fascia/ The ParkSense Rear Park Assist system provides visual bumper, monitor the area behind the vehicle that is and audible indications of the distance between the rear within the sensors’...
Page 250
248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The ParkSense Warning Display is located in the Instru- ParkSense Display ment cluster’s EVIC display. It provides both visual and When the vehicle is in REVERSE, the warning display audible warnings to indicate the distance between the will turn ON indicating the system status.
Page 251
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249 The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
Page 252
250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fast Tone Continuous Tone The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone. I n f o r ma t i o n P r o v i d e d b y :...
Page 253
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251 The following chart shows the warning alert operation when the system is detecting an obstacle: WARNING ALERTS Rear Distance Greater than 79-39 inches 39-25 inches 25-12 inches Less than (inches/cm) 79 inches (200 (200-100 cm) (100-65 cm) (65-30 cm)
Page 254
252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Enabling/Disabling ParkSense Service The ParkSense Rear Park Assist System ParkSense can be enabled and disabled through the During vehicle start up, when the ParkSense Rear Park Customer-Programmable Features section of the EVIC. Assist System has detected a faulted condition, the The available choices are: OFF, Sound Only, or Sound and instrument cluster will actuate a single chime, once per Display.
Page 255
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253 • When you move the shift lever to the REVERSE Cleaning The ParkSense System position and ParkSense is turned OFF, the EVIC will Clean the ParkSense sensors with water, car wash soap display “PARK ASSIST SYSTEM OFF” message for as and a soft cloth.
Page 256
254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE object as a sensor problem, causing the “SERVICE WARNING! PARK ASSIST SYSTEM” message to be displayed in • Drivers must be careful when backing up even the EVIC. when using ParkSense. Always check carefully CAUTION! behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles,...
Page 257
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255 When the vehicle is shifted out of REVERSE, the rear WARNING! (Continued) camera mode is exited and the last selected touchscreen could detect the ball mount and hitch ball assem- appears again. bly, depending on its size and shape, giving a false If your vehicle is equipped with the Camera Delay indication that an obstacle is behind the vehicle.
Page 258
256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When displayed, static grid lines will illustrate the width that will help indicate the distance to the rear of the of the vehicle while a dashed center-line will indicate the vehicle. The following table shows the approximate center of the vehicle to assist with aligning to a hitch/ distances for each zone: receiver.
Page 259
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257 lights, flip-down sunglass storage, conversation mirror, CAUTION! (Continued) optional power sliding door switches and an optional stop in time when an obstacle is seen. It is recom- power liftgate switch. mended that the driver look frequently over his/her NOTE: Premium sunroof console models include all of shoulder when using ParkView.
Page 260
258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Interior Lighting Sunglass Storage (Non-Sunroof Only) At the forward end of the console are two courtesy lights At the front of the overhead console, a compartment is (standard dome light has two buttons). The lights turn on provided for the storage of two pairs of sunglasses.
Page 261
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259 The door will slowly rotate to the full open position. Conversation Mirror Position NOTE: From the “conversation mirror” position, the Full Open Position door can only be closed. From this position, the door can be fully closed or, by rotating upward about 3/4 of the way and releasing, To return to the full open position, the door must first be positioned for conversation mirror use.
Page 262
260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Courtesy/Reading Lights — If Equipped The overhead console has two sets of courtesy lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pushed.
Page 263
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261 Rear Console Halo Lighting The rear overhead console has recessed halo lighting around the perimeter of the console base. This feature provides additional lighting options while traveling and is controlled by the headlight switch. Refer to “Lights/ Halo Lights —...
Page 264
262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink buttons, located on either the overhead console, headliner or sunvisor, designate the three differ- ent HomeLink channels. The HomeLink indicator is located above the center button. HomeLink Buttons/Sunvisor/Headliner NOTE: HomeLink is disabled when the Vehicle Security Alarm is active.
Page 265
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263 Before You Begin Programming HomeLink NOTE: • Erasing all channels should only be performed when Be sure that your vehicle is parked outside of the garage before you begin programming. programming HomeLink for the first time. Do not erase channels when programming additional buttons.
Page 266
264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink button you wish to program while keeping the HomeLink indicator light in view. 3. Push and hold the HomeLink button you want to program while you push and hold the hand-held transmitter button.
Page 267
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265 Firmly push and release the “LEARN” or “TRAIN- Reprogramming A Single HomeLink Button ING” button. On some garage door openers/devices (Rolling Code) there may be a light that blinks when the garage door To reprogram a channel that has been previously trained, opener/device is in the LEARN/TRAIN mode.
Page 268
266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To program the two remaining HomeLink buttons, 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink button you wish to repeat each step for each remaining button. DO NOT program while keeping the HomeLink indicator light erase the channels.
Page 269
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267 Canadian/Gate Operator Programming 3. Continue to push and hold the HomeLink button, while you push and release (“cycle”) your hand-held For programming transmitters in Canada/United States transmitter every two seconds until HomeLink has that require the transmitter signals to “time-out”...
Page 270
268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: 2. Push and hold the desired HomeLink button until the indicator light begins to flash after 20 seconds. Do not • If the indicator light stays on constantly, program- release the button. ming is complete and the garage door/device should activate when the HomeLink button is pushed.
Page 271
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269 • Push the LEARN button on the Garage Door Opener Security to complete the training for a Rolling Code. It is advised to erase all channels before you sell or turn • Did you unplug the device for programming and in your vehicle.
Page 272
270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. This device must accept any interference received, WARNING! (Continued) including interference that may cause undesired op- pets or other objects are in the path of the door or eration. gate. Only use this transceiver with a garage door NOTE: Changes or modifications not expressly approved opener that has a “stop and reverse”...
Page 273
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271 WARNING! (Continued) accessible to children. Do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go in the ACC or ON/RUN mode. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch.
Page 274
272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Express position. The sunroof will close fully and stop automati- cally. This is called “Express Close.” During Express Push the switch rearward and release it within one-half Close operation, any other actuation of the switch will second.
Page 275
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 273 NOTE: If three consecutive sunroof close attempts result Wind Buffeting in Pinch Protect reversals, Pinch Protect will disable and Wind buffeting can be described as the perception of the sunroof must be closed in Manual Mode. pressure on the ears or a helicopter-type sound in the ears.
Page 276
274 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ignition Off Operation directly to the battery. The driver-side power outlet will also operate a conventional cigar lighter unit (if equipped For Vehicles Not Equipped With The Electronic Vehicle with an optional Smoker’s Package). Information Center (EVIC) The power sunroof switch will remain active for 45 seconds after the ignition switch is turned to the LOCK...
Page 277
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 275 One outlet in the removable floor console (if equipped) CAUTION! shares a fuse with the lower outlet in the instrument • Do not exceed the maximum power of 160 Watts (13 panel and is also connected to the battery. Do not exceed a maximum power of 160 Watts (13 Amps) shared Amps) at 12 Volts.
Page 278
276 UNDERSTANDING THE FEATURES OF YOUR VEHICLE On vehicles equipped with the Super Console the power The outlet in the rear quarter panel near the liftgate and outlets are located under the retractable cover. To access the upper outlet in the instrument panel are both con- the power outlets push down on the cover and slide it trolled by the ignition switch.
Page 279
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 277 WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. •...
Page 280
278 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! (Continued) • Power outlets are designed for accessory plugs • Many accessories that can be plugged in draw only. Do not hang any type of accessory or acces- power from the vehicle’s battery, even when not in sory bracket from the plug.
Page 281
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 279 This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts. Certain high-end video game consoles will exceed this power limit, as will most power tools. The power inverter is designed with built-in overload protection.
Page 282
280 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Instrument Panel Cupholders WARNING! The instrument panel cupholders are located in a pull-out To avoid serious injury or death: drawer just above the lower storage bin. • Do not insert any objects into the receptacles. •...
Page 283
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 281 variety of container types and sizes. Push down on the For rear passengers two cupholders are located in the container to engage the cupholder retention features. pull-out drawer, located in the back of the Super Console. Pull the drawer out to the first position to use the Super Console —...
Page 284
282 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Premium Console Cupholders — If Equipped Interior Bottle Holders On models equipped with premium center consoles, There are four bottle holders located in the interior. One there are four cupholders located on the top of the bottle holder is molded into each front interior door trim console.
Page 285
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 283 Smoker’s Package Kit — If Equipped With the optional authorized dealer-installed Smoker’s Package Kit, a removable ash receiver is inserted into one of the two cupholders in the center front instrument panel. To install the ash receiver, align the receiver so the thumb grip on the lid is facing rearward.
Page 286
284 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Upper Glove Compartment Lower Glove Compartment To open the upper compartment, push in on the button, To open the lower compartment pull out on the release located on the left side of the upper door. The door will handle.
Page 287
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 285 Door Trim Panel Storage Front Door Storage Both interior front door panels have multiple pockets for storage. WARNING! If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burn- ing the occupants.
Page 288
286 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Umbrella Holder Second Row Floor Storage Bins An umbrella holder has been conveniently molded into The area below the floor covers, located in front of the the left front door entry scuff molding. second row seats, is available for storage.
Page 289
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 287 Pull up on the storage bin latch to open the cover. Slide WARNING! the storage bin locking mechanism to the unlocked position to allow greater access to the storage bin. In a collision, serious injury could result if the seat storage bin covers are not properly latched.
Page 290
288 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage Bin Safety Warning WARNING! (Continued) Carefully follow these warnings to help prevent personal • Do not operate the storage bin covers while the injury or damage to your vehicle: vehicle is in motion. •...
Page 291
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 289 Center And Rear Overhead Console Storage — If Equipped The overhead storage system comes in several options. Storage Bin Cover Emergency Release Lever NOTE: In the event of an individual being locked inside Overhead Console Features the storage bin, the storage bin cover can be opened from 1 —...
Page 292
290 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle.
Page 293
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 291 • The cupholders are removable to access a large storage CONSOLE FEATURES bin. There are three consoles available: Basic, Premium and • The basic console is removable from the vehicle for Super. additional floor space by removing the cap and clip at WARNING! the console base.
Page 294
292 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Four cupholders with dishwasher safe liners for clean- 3. Align the console until the front anchor cup plug hole is centered on the winch hole. ing. The cupholders can accept plastic bottles, large cups or mugs with handles 4.
Page 295
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 293 The top and center console sections slide forward and rearward to provide added user comfort. A one-piece cup holder insert for both cavities can easily be removed for cleaning. The cupholders will also accommodate large size cups and 20 oz (.6 L) bottles.
Page 296
294 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position 2 shows the raised storage tray revealing a large easy access to the storage area below and provides two of storage area below. the four cupholders for the second row passengers. Console Position 2 Console Position 3 Dual Storage Bins Position 4 shows the complete console in its rearmost...
Page 297
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 295 3. Pull rearward to disengage from floor and remove console. To Reinstall The Premium Floor Console: 1. Position the console at a slight angle (rear slightly higher than the front). 2. Slide the console forward into the floor bracket. 3.
Page 298
296 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched. Super Console — If Equipped The Super Console contains multiple storage areas, front lower pass through, top forward bin, top rearward bin and rear pull out drawer.
Page 299
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 297 NOTE: The front cupholder light ring and pass through lighting is controlled by a dimming switch located on the instrument panel, refer to “Lights” in “Understanding The Features Of Your Vehicle” for further information. Located in the back of the Super Console is a storage drawer and cupholders for the rear passengers.
Page 300
298 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES CAUTION! Rear Window Defroster Failure to follow these cautions can cause damage to The rear window defroster button is located on the heating elements: the climate control (Mode) knob. Push this button •...
Page 301
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 299 LOAD LEVELING SYSTEM — IF EQUIPPED crossbars, to maximum of 150 lbs (68 kg). The roof rack does not increase the total load carrying capacity of the The automatic load leveling system will provide a level- vehicle.
Page 302
300 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The crossbars and side rails are designed to carry weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. NOTE: •...
Page 303
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 301 Bend the crossbar supports at each end, taking care to keep hand clear of pivoting joint. Slide the thumb screw down. Deployed Position Stowed Position I n f o r ma t i o n P r o v i d e d b y :...
Page 304
302 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then, position the crossbars across the roof. Make sure the directional arrows on the crossbars align with the directional arrows on the side rails. Set the NOTE: The crossbars are identical and can be placed in crossbars into the deployed positions.
Page 305
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 303 Once the crossbars are set into position, tighten the Stowing The Crossbars thumb screws completely. Reverse the procedure to stow the crossbars, again, taking care to keep hand clear of pivoting joint. Crossbars are identical and can be stowed in either rail nest.
Page 306
304 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Load should always be secured to crossbars first, CAUTION! with rail tie down loops used as additional securing • Check deployed crossbars frequently and retighten points if needed. Tie loops are intended as supplemen- tary tie down points only.
Page 307
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 305 CAUTION! (Continued) WARNING! • Long loads which extend over the windshield, such Cargo must be securely tied before driving your as wood panels or surfboards, or loads with large vehicle. Improperly secured loads can fly off the frontal area should be secured to both the front and vehicle, particularly at high speeds, resulting in per- rear of the vehicle.
Page 308
306 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sun Screen Retracted Sun Screen Extended Gently pull up on the tab to raise the sun screen. To lower the sun screen, gently lift the tab upward to Continue pulling the sun screen until the tab is near the disengage the hooks, and feed the screen back into the top of the window.
Page 309
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT PANEL FEATURES ..312 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED ...346 INSTRUMENT CLUSTER — BASE ..313 ▫...
Page 310
308 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Vehicle Info (Customer Information Features) . .355 ▫ Operating Instructions — Radio Mode ..367 ▫ Messages # ......356 ▫...
Page 311
UNDERSTANDING YOUR INSTRUMENT PANEL 309 ▫ Operating Instructions (Uconnect Phone) — If ▫ Getting Started ..... . .400 Equipped ......392 ▫...
Page 312
310 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ VES Remote Control — If Equipped ..418 ▫ Information Mode Display ....430 ▫ Blu-ray Player Remote Control — If ▫...
Page 313
UNDERSTANDING YOUR INSTRUMENT PANEL 311 ▫ Manual Heating And Air Conditioning CD/DVD/Blu-ray Disc MAINTENANCE ..447 System — If Equipped ....449 RADIO OPERATION AND MOBILE ▫...
Page 314
312 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 — Air Vents 5 — Analog Clock 9 — DVD – If Equipped 13 — Ignition Switch 2 — Instrument Cluster 6 — Upper Glove Compartment 10 — Storage Bin 14 — Hood Release 3 —...
Page 315
UNDERSTANDING YOUR INSTRUMENT PANEL 313 INSTRUMENT CLUSTER — BASE I n f o r ma t i o n P r o v i d e d b y :...
Page 316
314 UNDERSTANDING YOUR INSTRUMENT PANEL 1. Tachometer make a record of the odometer reading before the repair/ • This gauge measures engine revolutions per minute service, so that you can be sure that it is properly reset, or that the door jamb sticker is accurate if the odometer (RPM x 1000).
Page 317
UNDERSTANDING YOUR INSTRUMENT PANEL 315 NOTE: Some of the above warnings will be displayed in noFUSE the Electronic Vehicle Information Center Display Area If the vehicle diagnostic system determines that the located in the instrument cluster. Ignition Off Draw (IOD) fuse is improperly installed, or Refer to ”Electronic Vehicle Information Center (EVIC) —...
Page 318
316 UNDERSTANDING YOUR INSTRUMENT PANEL Unless reset, this message will continue to display each Electronic Vehicle Information Center (EVIC) — If time you turn the ignition switch to the ON/RUN Equipped position. To reset the oil change indicator system (after The Electronic Vehicle Information Center (EVIC) features performing the scheduled maintenance), perform the a driver-interactive display that is located in the instrument...
Page 319
UNDERSTANDING YOUR INSTRUMENT PANEL 317 5. Temperature Gauge WARNING! • The temperature gauge shows engine coolant tem- A hot engine cooling system is dangerous. You or perature. Any reading within the normal range indi- others could be badly burned by steam or boiling cates that the engine cooling system is operating coolant.
Page 320
318 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — PREMIUM I n f o r ma t i o n P r o v i d e d b y :...
Page 321
UNDERSTANDING YOUR INSTRUMENT PANEL 319 1. Tachometer U.S. Federal regulations require that upon transfer of • This gauge measures engine revolutions per minute vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. If your (RPM x 1000).
Page 322
320 UNDERSTANDING YOUR INSTRUMENT PANEL Message Display Area gASCAP When the appropriate conditions exist, the following If the vehicle diagnostic system determines that the fuel odometer messages will display: filler cap is loose, improperly installed, or damaged, a door ......Door Ajar “gASCAP”...
Page 323
UNDERSTANDING YOUR INSTRUMENT PANEL 321 single chime has sounded, to indicate the next scheduled 3. Speedometer oil change interval. The engine oil change indicator system • Indicates vehicle speed. is duty cycle-based, which means the engine oil change 4. Fuel Gauge interval may fluctuate dependent upon your personal •...
Page 324
322 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING AND INDICATOR LIGHTS CAUTION! IMPORTANT: The warning / indicator light switches on Driving with a hot engine cooling system could in the instrument panel together with a dedicated mes- damage your vehicle. If the temperature gauge reads sage and/or acoustic signal when applicable.
Page 325
UNDERSTANDING YOUR INSTRUMENT PANEL 323 Red Telltale Indicator Lights Air Bag Warning Light Red Telltale What It Means Light Air Bag Warning Light This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to ON/RUN.
Page 326
324 UNDERSTANDING YOUR INSTRUMENT PANEL Seat Belt Reminder Warning Light Red Telltale What It Means Light Seat Belt Reminder Warning Light When the ignition switch is first turned to ON/RUN, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound.
Page 327
UNDERSTANDING YOUR INSTRUMENT PANEL 325 Brake Warning Light Red Telltale What It Means Light Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reser- voir.
Page 328
326 UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capac- Vehicles equipped with the Anti-Lock Brake System ity in the event of a failure to a portion of the hydraulic (ABS) are also equipped with Electronic Brake Force system.
Page 329
UNDERSTANDING YOUR INSTRUMENT PANEL 327 Charging System Warning Light Red Telltale What It Means Light Charging System Warning Light This light shows the status of the electrical charging system. If the light stays on or comes on while driving, turn off some of the vehicle’s nonessential electrical devices or increase engine speed (if at idle).
Page 330
328 UNDERSTANDING YOUR INSTRUMENT PANEL Coolant Temperature Warning Light Red Telltale What It Means Light Coolant Temperature Warning Light This light warns of an overheated engine condition. If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the vehicle.
Page 331
UNDERSTANDING YOUR INSTRUMENT PANEL 329 Electronic Throttle Control (ETC) Warning Light Red Telltale What It Means Light Electronic Throttle Control (ETC) Warning Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a problem is detected while the engine is running, the light will either stay on or flash de- pending on the nature of the problem.
Page 332
330 UNDERSTANDING YOUR INSTRUMENT PANEL Oil Pressure Warning Light Red Telltale What It Means Light Oil Pressure Warning Light This light indicates low engine oil pressure. If the light turns on while driving, stop the ve- hicle and shut off the engine as soon as possible. A chime will sound when this light turns Do not operate the vehicle until the cause is corrected.
Page 333
UNDERSTANDING YOUR INSTRUMENT PANEL 331 Transmission Temperature Warning Light Red Telltale What It Means Light Transmission Temperature Warning Light This light indicates that the transmission fluid temperature is running hot. This may occur with severe usage. If this light turns on, safely pull over and stop the vehicle. Then, shift the trans- mission into NEUTRAL and run the engine at idle or faster until the light turns off.
Page 334
332 UNDERSTANDING YOUR INSTRUMENT PANEL Door Open Warning Light — If Equipped Red Telltale What It Means Light Door Open Warning Light This indicator will illuminate when a door is ajar/open and not fully closed. NOTE: If the vehicle is moving, there will also be a single chime. Liftgate Open Warning Light Red Telltale What It Means...
Page 335
UNDERSTANDING YOUR INSTRUMENT PANEL 333 Yellow Telltale Indicator Lights Anti-Lock Brake (ABS) Indicator Light Yellow Telltale What It Means Light Anti-Lock Brake (ABS) Indicator Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the igni- tion switch is placed in the ON/RUN position and may stay on for as long as four seconds.
Page 336
334 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Stability Control (ESC) Indicator Light — If Equipped Yellow Telltale What It Means Light Electronic Stability Control (ESC) Indicator Light — If Equipped The “ESC Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON/RUN position.
Page 337
UNDERSTANDING YOUR INSTRUMENT PANEL 335 Electronic Stability Control (ESC) OFF Indicator Light — If Equipped Yellow Telltale What It Means Light Electronic Stability Control (ESC) OFF Indicator Light — If Equipped This light indicates the Electronic Stability Control (ESC) is off. Loose Fuel Filler Cap Indicator Light —...
Page 338
336 UNDERSTANDING YOUR INSTRUMENT PANEL Low Fuel Indicator Light Yellow Telltale What It Means Light Low Fuel Indicator Light When the fuel level reaches approximately 1.5 gal (5.8 L) this light will turn on, and remain on until fuel is added. Low Washer Fluid Indicator Light —...
Page 339
UNDERSTANDING YOUR INSTRUMENT PANEL 337 Engine Check/Malfunction Indicator Light (MIL) Yellow Telltale What It Means Light Engine Check/Malfunction Indicator Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems. The light will illuminate when the ignition is in the ON position before engine start.
Page 340
338 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! WARNING! Prolonged driving with the Malfunction Indicator A malfunctioning catalytic converter, as referenced Light (MIL) on could cause damage to the engine above, can reach higher temperatures than in normal control system. It also could affect fuel economy and operating conditions.
Page 341
UNDERSTANDING YOUR INSTRUMENT PANEL 339 Tire Pressure Monitoring Indicator Light Yellow Telltale What It Means Light Tire Pressure Monitoring Indicator Light The warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tire duration and fuel consumption may not be guaranteed.
Page 342
340 UNDERSTANDING YOUR INSTRUMENT PANEL on the vehicle placard or tire inflation pressure label, you Please note that the TPMS is not a substitute for proper should determine the proper tire inflation pressure for tire maintenance, and it is the driver’s responsibility to those tires.
Page 343
UNDERSTANDING YOUR INSTRUMENT PANEL 341 When the malfunction indicator is illuminated, the sys- CAUTION! tem may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety The TPMS has been optimized for the original of reasons, including the installation of replacement or equipment tires and wheels.
Page 344
342 UNDERSTANDING YOUR INSTRUMENT PANEL Green Telltale Indicator Lights Turn Signal Indicator Lights Green Tell- What It Means tale Light Turn Signal Indicator Lights The instrument cluster arrow will flash independently for the LEFT or RIGHT turn signal as se- lected, as well as the exterior turn signal lamp(s) (front and rear) as selected when the multi- function lever is moved down (LEFT) or up (RIGHT).
Page 345
UNDERSTANDING YOUR INSTRUMENT PANEL 343 Park/Headlight ON Indicator Light Green Telltale What It Means Light Park/Headlight ON Indicator Light This indicator will illuminate when the park lights or headlights are turned on. Front Fog Indicator Light — If Equipped Green Telltale What It Means Light Front Fog Indicator Light —...
Page 346
344 UNDERSTANDING YOUR INSTRUMENT PANEL Blue Telltale Indicator Light High Beam Indicator Light Blue Telltale What It Means Light High Beam Indicator Light This indicator shows that the high beam headlights are on. Push the multifunction control lever away from you to switch the headlights to high beam. Pull the lever toward you to switch the headlights back to low beam.
Page 347
UNDERSTANDING YOUR INSTRUMENT PANEL 345 White Telltale Indicator Light Cruise Control Cancelled Light White Telltale What It Means Light Cruise Control Cancelled Light This light will turn on when the cruise control has been cancelled by the driver. Refer to “Electronic Speed Control”...
Page 348
346 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER The EVIC Menu items consists of the following: (EVIC) — IF EQUIPPED • Fuel Economy The Electronic Vehicle Information Center (EVIC) fea- • Vehicle Speed tures a driver-interactive display that is located in the •...
Page 349
UNDERSTANDING YOUR INSTRUMENT PANEL 347 • UP Button The system allows the driver to select information by pushing the following buttons mounted on the steering Push and release the UP button to scroll up- wheel: ward through the main menu items (Fuel Economy, Vehicle Info, Tire PSI, Cruise, Mes- sages, Units, System Setup).
Page 350
348 UNDERSTANDING YOUR INSTRUMENT PANEL Once the RIGHT button has been selected for the desired The main display area will normally display the main submenu list, follow the EVIC prompts to properly select menu or the screens of a selected feature of the main the desired submenu EVIC features.
Page 351
UNDERSTANDING YOUR INSTRUMENT PANEL 349 • Unstored Messages The Reconfigurable Telltales section is divided into the white telltales area on the right, amber telltales in the This message type is displayed indefinitely or until the middle, and red telltales on the left. condition that activated the message is cleared.
Page 352
350 UNDERSTANDING YOUR INSTRUMENT PANEL • Wrong Key • Turn Signal On • Damaged Key • RKE Battery Low • Key not programmed • Service Keyless System • Vehicle Not in Park • Low Washer Fluid • Key Left Vehicle •...
Page 353
UNDERSTANDING YOUR INSTRUMENT PANEL 351 • Blind Spot System Off — This message is displayed Oil Change Required when the ignition is turned to ON to indicate the Blind Your vehicle is equipped with an engine oil change Spot System has been turned off. indicator system.
Page 354
352 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicles Equipped With Keyless Enter-N-Go NOTE: If the indicator message illuminates when you start the engine, the oil change indicator system did not 1. Without pushing the brake pedal, push the ENGINE reset. If necessary, repeat these steps. START/STOP button and cycle the ignition to the ON/RUN position (do not start the engine).
Page 355
UNDERSTANDING YOUR INSTRUMENT PANEL 353 seconds. Then, the history information will be erased, and average fuel economy, according to the current fuel and the averaging will continue from the last fuel aver- tank level. DTE cannot be reset through the RIGHT age reading before the reset.
Page 356
354 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicle Speed Trip A • Shows the total distance traveled for Trip A since the Push and release the UP or DOWN button until “Vehicle Speed” displays highlighted in the EVIC and push the last reset. RIGHT arrow button.
Page 357
UNDERSTANDING YOUR INSTRUMENT PANEL 355 To Reset A Trip Function and release the RIGHT button until a check-mark ap- pears next to the setting, showing that the setting has Reset will only occur while a resettable function is been selected. selected (highlighted).
Page 358
356 UNDERSTANDING YOUR INSTRUMENT PANEL • Engine Hours Refer to “Keyless Enter-N-Go” in “Starting And Operat- ing” for further information. Displays the number of hours of engine operation. Compass / Temperature Display Messages # The compass readings indicate the direction the vehicle is Select from Main Menu using the UP or DOWN buttons.
Page 359
UNDERSTANDING YOUR INSTRUMENT PANEL 357 Automatic Compass Calibration 2. Push and release the UP or DOWN button until the System Setup (Customer-Programmable Features) This compass is self-calibrating, which eliminates the menu is reached, then push and release the RIGHT need to manually reset the compass. When the vehicle is button.
Page 360
358 UNDERSTANDING YOUR INSTRUMENT PANEL Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To compensate for the differences the variance should be set for the zone where the vehicle is driven, per the zone map. Once properly set, the compass will automatically compensate for the differences, and provide the most accurate compass heading.
Page 361
UNDERSTANDING YOUR INSTRUMENT PANEL 359 3. Push and release the DOWN button until the “Com- message SYSTEM SETUP NOT AVAILABLE VEHICLE pass Variance” message is displayed in the EVIC, then NOT IN PARK displays when you try to select “System press the RIGHT button.
Page 362
360 UNDERSTANDING YOUR INSTRUMENT PANEL Nav–Turn By Turn showing the system has been activated or the check-mark is removed showing the system has been deactivated. When this feature is selected, the navigation system Refer to “Rear Park Assist System” in “Understanding utilizes voice commands, guiding you through the drive The Features Of Your Vehicle”...
Page 363
UNDERSTANDING YOUR INSTRUMENT PANEL 361 the feature showing the system has been activated, or the RKE Linked To Memory- If Equipped check-mark is removed showing the system has been When this feature is selected, the memory seat, mirror, deactivated. and radio settings will return to the memory set position when the RKE transmitter UNLOCK button is pushed.
Page 364
362 UNDERSTANDING YOUR INSTRUMENT PANEL RIGHT arrow button until a check-mark appears next to showing the system has been activated or the check-mark the feature showing the system has been activated or the is removed showing the system has been deactivated. check-mark is removed showing the system has been Automatic High Beams —...
Page 365
UNDERSTANDING YOUR INSTRUMENT PANEL 363 Headlamps With Wipers (Available With Auto the RIGHT button until a check-mark appears next to the Headlights Only) feature showing the system has been activated or the check-mark is removed showing the system has been When ON is selected, and the headlight switch is in the deactivated.
Page 366
364 UNDERSTANDING YOUR INSTRUMENT PANEL Illuminated Approach signaling other drivers that someone may be exiting or entering the vehicle. To make your selection, push and When this feature is selected, the headlights will activate release the RIGHT button until a check-mark appears and remain on for up to 90 seconds when the doors are next to the feature showing the system has been activated unlocked with the RKE transmitter.
Page 367
UNDERSTANDING YOUR INSTRUMENT PANEL 365 vehicle. To make your selection, push and release the showing the system has been activated, or the check- RIGHT button until a check-mark appears next to the mark is removed showing the system has been deacti- feature showing the system has been activated or the vated.
Page 368
366 UNDERSTANDING YOUR INSTRUMENT PANEL To make your selection, push and release the RIGHT UCONNECT 430/430N CD/DVD/HDD/NAV — IF button until a check-mark appears next to the feature, EQUIPPED showing the system has been activated, or the check- Refer to your Uconnect Supplement Manual for detailed mark is removed, showing the system has been deacti- operating instructions.
Page 369
UNDERSTANDING YOUR INSTRUMENT PANEL 367 UCONNECT 130 Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction, without stopping.
Page 370
368 UNDERSTANDING YOUR INSTRUMENT PANEL another selection. Holding either button will bypass 5. To exit, push any button/knob, or wait five seconds. stations without stopping, until you release it. RW/FF TIME Button Pushing the RW (Rewind) or FF (Fast Forward) buttons Push the TIME button to alternate display of the time and causes the tuner to search for the next frequency in the radio frequency.
Page 371
UNDERSTANDING YOUR INSTRUMENT PANEL 369 Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the AM/FM Button mid-range tones.
Page 372
370 UNDERSTANDING YOUR INSTRUMENT PANEL display window. Each button can be set for SET 1 and Operation Instructions — CD MODE For CD And SET 2 in both AM and FM. This allows a total of 12 AM MP3 Audio Play and 12 FM stations to be stored into pushbutton memory.
Page 373
UNDERSTANDING YOUR INSTRUMENT PANEL 371 If you insert a disc with the ignition ON and the radio CAUTION! (Continued) ON, the unit will switch from radio to CD mode and • Dual-media disc types (one side is a DVD, the begin to play when you insert the disc.
Page 374
372 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button AM/FM Button Push the right SEEK button for the next selection on the Push the button to select either AM or FM mode. CD. Push the left SEEK button to return to the beginning SET/RND Button (Random Play Button) of the current selection, or return to the beginning of the Push this button while the CD is playing to activate...
Page 375
UNDERSTANDING YOUR INSTRUMENT PANEL 373 Supported Media (Disc Types) the file name and folder name, and will assign a number instead. With a maximum number of files, exceeding 20 The MP3 file recording media supported by the radio are folders will result in this display. With 200 files, exceed- CDDA, CD-R, CD-RW, MP3, and CDDA+MP3.
Page 376
374 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats MPEG Sampling Fre- Bit Rate (kbps) Specification quency (kHz) The radio will recognize only files with the *.MP3 exten- sion as MP3 files. Non-MP3 files named with the *.MP3 MPEG-1 Audio 48, 44.1, 32 320, 256, 224, extension may cause playback problems.
Page 377
UNDERSTANDING YOUR INSTRUMENT PANEL 375 Playback Of MP3 Files To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a When a medium containing MP3 data is loaded, the single-session disc, enable the “Disc at Once” option radio checks all files on the medium.
Page 378
376 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Operating Instructions — Radio Mode Push this button to change the display to time of day. The NOTE: The ignition switch must be in the ON/RUN or time of day will display for five seconds (when ignition is ACC position to operate the radio.
Page 379
UNDERSTANDING YOUR INSTRUMENT PANEL 377 SEEK Buttons If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With Push and release the SEEK buttons to search for the next Uconnect Phone” message will display on the radio listenable station in AM/FM mode.
Page 380
378 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure starting at step 2. For vehicles not equipped with satellite radio, push the SETUP button and then follow the above 1. Push and hold the TIME button until the hours blink. procedure, starting at step 2. 2.
Page 381
UNDERSTANDING YOUR INSTRUMENT PANEL 379 Setting The Tone, Balance And Fade Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control Push the rotary TUNE/SCROLL control knob and BASS knob to the left or right to adjust the sound level between will display.
Page 382
380 UNDERSTANDING YOUR INSTRUMENT PANEL 16-Digit Character 16-Digit Character Program Type Program Type Display Display No program type None Public Public or undefined Rhythm and Blues R & B Adult Hits Adlt Hit Religious Music Rel Musc Classical Classicl Religious Talk Rel Talk Classic Rock Cls Rock...
Page 383
UNDERSTANDING YOUR INSTRUMENT PANEL 381 By pushing the SEEK button when the Music Type icon is the minutes using the right side TUNE/SCROLL con- displayed, the radio will be tuned to the next frequency trol knob. Push the TUNE/SCROLL control knob to station with the same selected Music Type name.
Page 384
382 UNDERSTANDING YOUR INSTRUMENT PANEL the SET/RND button twice and SET 2 will show in the Operation Instructions — CD MODE For CD And display window. Each button can be set for SET 1 and MP3 Audio Play SET 2 in both AM and FM. This allows a total of 12 AM NOTE: and 12 FM stations to be stored into pushbutton memory.
Page 385
UNDERSTANDING YOUR INSTRUMENT PANEL 383 If you insert a disc with the ignition ON/RUN and the CAUTION! (Continued) radio ON, the unit will switch from radio to CD mode • Dual-media disc types (one side is a DVD, the and begin to play when you insert the disc. The display other side is a CD) should not be used, and they can will show the track number, and index time in minutes cause damage to the player.
Page 386
384 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button AM/FM Button Push the right SEEK button for the next selection on the Push the button to select either AM or FM mode. CD. Push the left SEEK button to return to the beginning SET/RND Button (Random Play Button) of the current selection, or return to the beginning of the Push this button while the CD is playing to activate...
Page 387
UNDERSTANDING YOUR INSTRUMENT PANEL 385 Supported Media (Disc Types) the file name and folder name, and will assign a number instead. With a maximum number of files, exceeding 20 The MP3 file recording media supported by the radio are folders will result in this display. With 200 files, exceed- CDDA, CD-R, CD-RW, MP3, and CDDA+MP3.
Page 388
386 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats MPEG Sampling Fre- Bit Rate (kbps) Specification quency (kHz) The radio will recognize only files with the *.MP3 exten- sion as MP3 files. Non-MP3 files named with the *.MP3 MPEG-1 Audio 48, 44.1, 32 320, 256, 224, extension may cause playback problems.
Page 389
UNDERSTANDING YOUR INSTRUMENT PANEL 387 Playback Of MP3 Files LIST Button — CD Mode For MP3 Play When a medium containing MP3 data is loaded, the Pushing the LIST button will bring up a list of all folders radio checks all files on the medium. If the medium on the disc.
Page 390
388 UNDERSTANDING YOUR INSTRUMENT PANEL Push and hold the INFO button again for three seconds TIME Button (Auxiliary Mode) to return to elapsed time display. Push this button to change the display to time of day. The time of day will display for five seconds (when the Operation Instructions —...
Page 391
UNDERSTANDING YOUR INSTRUMENT PANEL 389 System Activation To access the ESN/SID, refer to the following steps: Sirius Satellite Radio service is pre-activated, and you ESN/SID Access may begin listening immediately to the one year of audio With the ignition switch in the ON/RUN or ACC posi- service that is included with the factory-installed satellite tion and the radio on, push the SETUP button and scroll radio system in your vehicle.
Page 392
390 UNDERSTANDING YOUR INSTRUMENT PANEL decreased performance. Larger luggage items such as Operating Instructions — Uconnect (Satellite) bikes should be placed as far rearward as possible, within Mode the loading design of the rack. Do not place items directly NOTE: The ignition switch must be in the ON/RUN or on or above the antenna.
Page 393
UNDERSTANDING YOUR INSTRUMENT PANEL 391 INFO Button MUSIC TYPE Button Pushing the INFO button will cycle the display informa- Pushing this button once will turn on the Music Type tion between Artist, Song Title, and Composer (if avail- mode for five seconds. Pushing the MUSIC TYPE button able).
Page 394
392 UNDERSTANDING YOUR INSTRUMENT PANEL SETUP Button You may add a second channel to each pushbutton by repeating the above procedure with this exception: Push Pushing the SETUP button allows you to select the the SET button twice and SET 2 will show in the display following items: window.
Page 395
UNDERSTANDING YOUR INSTRUMENT PANEL 393 SETTING THE ANALOG CLOCK iPod/USB/MP3 CONTROL — IF EQUIPPED To set the analog clock at the top center of the instrument This feature allows an iPod or external USB device to be panel, press and hold the button until the setting is plugged into the USB port, located in the glove compart- correct.
Page 396
394 UNDERSTANDING YOUR INSTRUMENT PANEL Connecting The iPod Or External USB Device NOTE: The glove compartment will have a position where the iPod or consumer electronic audio device cable Use the connection cable to connect an iPod or external can be routed through without damaging the cable when USB device to the vehicle’s USB connector port which is closing the lid.
Page 397
UNDERSTANDING YOUR INSTRUMENT PANEL 395 Using This Feature control mode, audio tracks (if available from audio device) start playing over the vehicle’s audio system. By using an external USB device to connect to the USB port: Play Mode • The audio device can be played on the vehicle’s sound When switched to iPod/USB/MP3 control mode, the system, providing metadata (artist, track title, album, iPod or external USB device automatically starts Play...
Page 398
396 UNDERSTANDING YOUR INSTRUMENT PANEL • Jump backward in the current track by pushing and the next screen of data for that track. Once all screens holding the << RW button. Holding the << RW button have been viewed, the last INFO button push will go long enough will jump to the beginning of the current back to the play mode screen on the radio.
Page 399
UNDERSTANDING YOUR INSTRUMENT PANEL 397 device, or push the VR button and say Shuffle ON or through the list faster. During fast scroll, a slight delay Shuffle Off. If the RND icon is showing on the radio in updating the information on the radio display may display, then the shuffle mode is ON.
Page 400
398 UNDERSTANDING YOUR INSTRUMENT PANEL Pushing a PRESET button will display the current list on CAUTION! the top line and the first item in that list on the second • Leaving the iPod or external USB device (or any line. supported device) anywhere in the vehicle in ex- To exit List mode without selecting a track, push the treme heat or cold can alter the operation or dam-...
Page 401
UNDERSTANDING YOUR INSTRUMENT PANEL 399 Bluetooth Streaming Audio (BTSA) Selecting A Different Audio Device Music can be streamed from your cellular phone to the 1. Push the Phone button to begin. Uconnect phone system. 2. After the Ready prompt and following the beep, say Refer to the Uconnect Radio Supplement for further Setup , then say Select Audio Devices.
Page 402
400 UNDERSTANDING YOUR INSTRUMENT PANEL Browse Browsing is not available on a Bluetooth Streaming Audio (BTSA) device. Only the current song that is playing will display info. UCONNECT MULTIMEDIA — VIDEO ENTERTAINMENT SYSTEM (VES) — IF EQUIPPED Your rear seat Video Entertainment System (VES) is designed to give your family years of enjoyment.
Page 403
UNDERSTANDING YOUR INSTRUMENT PANEL 401 • Turn on the Player (if equipped on Dual Screen Sys- Blu-ray Disc Player tem) by pushing the Power button, located on the far Play A Blu-ray Disc left, or by pushing the button on the Remote Control. To view a Blu-ray disc, insert the disc into the Blu-ray •...
Page 404
402 UNDERSTANDING YOUR INSTRUMENT PANEL • Not all Blu-ray, CD or DVD discs will automatically • Press the 1 button on the touchscreen to select an audio restart from where you left off at when turned off. Some channel, then press the VES Disc button on the touch- discs will restart from the beginning, others will restart screen in the media column.
Page 405
UNDERSTANDING YOUR INSTRUMENT PANEL 403 When connecting an external source to the AUX input, be sure to follow the standard color coding for the VES jacks: NOTE: Certain high-end video games, such as Playsta- tion3 and XBox360 will exceed the power limit of the vehicle’s Power Inverter.
Page 406
404 UNDERSTANDING YOUR INSTRUMENT PANEL Using The Remote Control 1. Push the MODE button on the Remote Control. 2. While looking at the video screen, highlight VES AUX 1, by either pushing Up/Down/Left/Right buttons or by repeatedly pushing the MODE button, then push ENTER on the Remote Control.
Page 407
UNDERSTANDING YOUR INSTRUMENT PANEL 405 2. Press the Rear VES button on the touchscreen to 3. Press the 1 button on the touchscreen and then press display the Rear VES Controls. If a channel list is either AUX 1 or AUX 2 in the VES column (depending displayed, press the HIDE LIST button on the touch- which AUX input is used).
Page 408
406 UNDERSTANDING YOUR INSTRUMENT PANEL Listen To An Audio Source On Channel 2 While A Video Is Playing On Channel 1 Ensure the Remote Control and Headphone switch is on Channel 2. Using The Remote Control 1. Push the SOURCE button on the Remote Control and the Mode Select Screen will display, unless a video is playing then only a small banner will appear on the bottom of the screen.
Page 409
UNDERSTANDING YOUR INSTRUMENT PANEL 407 2. Press the Rear VES button on the touchscreen to 3. To listen to an audio source on Channel 2 while a display the Rear VES Controls. If a channel list is video is playing on Channel 1, press the 2 button on displayed, press the HIDE LIST button on the touch- the touchscreen and choose an audio source.
Page 410
408 UNDERSTANDING YOUR INSTRUMENT PANEL Dual Video Screen 2. Insert the DVD with the label facing up. The radio automatically selects the appropriate mode after the NOTE: Typically there are two different ways to operate disc is recognized and displays the menu screen or the features of the Video Entertainment System (VES).
Page 411
UNDERSTANDING YOUR INSTRUMENT PANEL 409 2. While looking at Screen 1 or 2, highlight DISC by NOTE: either pushing Up/Down/Left/Right buttons or by • Channel/Screen 1 select mode information is shown repeatedly pushing the SOURCE button, then push on the left side of the screen. ENTER/OK.
Page 412
410 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Press the Rear VES button on the touchscreen to 3. Press the 1 or 2 button on the touchscreen and then the display the Rear VES Controls. If a channel list is DISC button on the touchscreen in the MEDIA col- displayed, press the HIDE LIST button on the touch- umn.
Page 413
UNDERSTANDING YOUR INSTRUMENT PANEL 411 • Viewing a DVD on the Touchscreen radio screen is not NOTE: The VES player has basic DVD control function available in all states/provinces. If available, the ve- such as Menu, Play, Pause, FF, RW and Stop. hicle must be stopped and the shift lever must be in the 2.
Page 414
412 UNDERSTANDING YOUR INSTRUMENT PANEL 2. While looking at Screen 1 or 2, highlight VES DISC by NOTE: either pushing Up/Down/Left/Right buttons or by • Channel/Screen 1 select mode information is shown repeatedly pushing the SOURCE button, then push on the left side of the screen. ENTER/OK on the Remote Control.
Page 415
UNDERSTANDING YOUR INSTRUMENT PANEL 413 Rear VES Button On The Touchscreen Select Channel/Screen 1 And DISC In The VES Column 3. Press the 1 or 2 button on the touchscreen and then the NOTE: DISC button on the touchscreen in the VES column. To •...
Page 416
414 UNDERSTANDING YOUR INSTRUMENT PANEL • Viewing a DVD on the Touchscreen radio screen is not 3. To watch a Blu-ray Disc on Screen 2 for third row available in all states/provinces. If available, the ve- passengers, ensure the Remote Control and Head- hicle must be stopped and the shift lever must be in the phone switch is on Channel 2.
Page 417
UNDERSTANDING YOUR INSTRUMENT PANEL 415 • Viewing a Blu-ray Disc on the Touchscreen radio Using The Touchscreen Radio Controls screen is not available in all states/provinces. If avail- 1. Push the MENU button on the radio faceplate. able, the vehicle must be stopped and the shift lever 2.
Page 418
416 UNDERSTANDING YOUR INSTRUMENT PANEL Using The Remote Control 1. Push the SOURCE button on the Remote Control and the Mode Select Screen will display, unless a video is playing then only a small banner will appear on the bottom of the screen. 2.
Page 419
UNDERSTANDING YOUR INSTRUMENT PANEL 417 Rear VES Button On The Touchscreen Select Channel/Screen 2 And HDD In The Media Column 3. To listen to an audio source on Channel 2 while a Important Notes For Dual Video Screen System video is playing on Channel 1, press the 2 button on the touchscreen and choose an audio source.
Page 420
418 UNDERSTANDING YOUR INSTRUMENT PANEL • The Blu-ray Disc Player can play CDs, DVDs and VES Remote Control — If Equipped Blu-ray Discs. • The DVD Player can play CDs and DVDs. • In split screen mode the left side equates to Channel 1 and the right side equates to Channel 2.
Page 421
UNDERSTANDING YOUR INSTRUMENT PANEL 419 2. Channel Selector Indicators – When a button is / Prev – In radio modes, push to select to the pushed, the currently affected channel or channel previous station. In disc modes, push to advance to the button is illuminated momentarily.
Page 422
420 UNDERSTANDING YOUR INSTRUMENT PANEL listening to a disc in a radio with a multiple-disc selected and the disc is stopped, push the SETUP changer, PROG Up selects the next disc and PROG button to access the DVD Setup menu. (see the DVD Down selects the previous disc.
Page 423
UNDERSTANDING YOUR INSTRUMENT PANEL 421 Blu-ray Player Remote Control — If Equipped audio while the screen is closed, push the Power button to turn the headphone transmitter on. 2. Channel Selector Indicators – When a button is pushed, the currently affected channel or channel button is illuminated momentarily.
Page 424
422 UNDERSTANDING YOUR INSTRUMENT PANEL equipped) and the VES mode is selected and the disc – Push and release to jump to the previous audio is stopped, push the SETUP button to access the track or video chapter. Push and hold to fast rewind Blu-ray Setup menu.
Page 425
UNDERSTANDING YOUR INSTRUMENT PANEL 423 try to pull the remote straight down as it will be very Locking The Remote Control difficult to remove. To return the remote back into its All remote control functionality can be disabled as a storage area, insert one long edge of the remote into the parental control feature.
Page 426
424 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Replace the batteries, making sure to orient them according to the polarity diagram shown. 3. Replace the battery compartment cover. Headphones Operation The headphones receive two separate channels of audio using an infrared transmitter from the video screen. Front seat occupants receive some headphone audio coverage to allow them to adjust the headphone volume for the young rear seat occupants that may not be able to...
Page 427
UNDERSTANDING YOUR INSTRUMENT PANEL 425 Blu-ray Headphones Operation The headphones receive two separate channels of audio using an infrared transmitter from the video screen. Front seat occupants receive some headphone audio coverage to allow them to adjust the headphone volume for the young rear seat occupants that may not be able to do so for themselves.
Page 428
426 UNDERSTANDING YOUR INSTRUMENT PANEL Controls NOTE: • When both switches are on Channel 1, the Remote is The headphone power indicator and controls are located controlling Channel 1 and the headphones are tuned on the right ear cup. to the audio of the VES Channel 1. NOTE: The rear video system must be turned on before •...
Page 429
UNDERSTANDING YOUR INSTRUMENT PANEL 427 4. When the Mode Selection menu appears on screen, Unwired Stereo Headphone Lifetime Limited use the cursor buttons on the remote control to navi- Warranty gate to the available modes and push the OK button to Who Does This Warranty Cover? This warranty covers select the new mode.
Page 430
428 UNDERSTANDING YOUR INSTRUMENT PANEL What Does This Warranty Not Cover? This warranty What Will Unwired Do? Unwired, at its option, will does not cover any damage or defect that results from repair or replace any defective Product. Unwired re- misuse, abuse or modification of the Product other than serves the right to replace any discontinued Product with by Unwired.
Page 431
UNDERSTANDING YOUR INSTRUMENT PANEL 429 System Information the ability to switch tuner (AM/FM), SEEK, SCAN, TUNE, and recall presets in radio modes as long as it is Shared Modes not in shared mode. This allows the VES to output radio sources to the When in shared disc mode both the radio and the VES headphones and the radio to output VES sources to the have control of the video functions.
Page 432
430 UNDERSTANDING YOUR INSTRUMENT PANEL Information Mode Display Numeric Keypad Menu Information Mode Video Screen Display 1 — Channel 1 Mode 7 — Channel 1 ENTER/OK Numeric Keypad Menu 2 — Channel 1 Shared Status Button Action When the display for either Channel 1 or Channel 2 3 —...
Page 433
UNDERSTANDING YOUR INSTRUMENT PANEL 431 1. Push the remote control’s navigation buttons ( , , , Disc Menu ) to navigate to the desired digit. 2. When the digit is highlighted, push the remote con- trol’s ENTER/OK button to select the digit. Repeat these steps until all digits are entered.
Page 434
432 UNDERSTANDING YOUR INSTRUMENT PANEL Display Settings Listening To Audio With The Screen Closed When watching a video source (DVD Video with the disc To listen to only audio portion of the channel with the in Play mode, Aux Video, etc.), pushing the remote screen closed: control’s SETUP button activates the Display Settings 1.
Page 435
UNDERSTANDING YOUR INSTRUMENT PANEL 433 • CD: CD-DA, VCD, CD-TEXT Disc Formats • DVD/CD: MP3, WMA, AAC, DivX (versions 3 – 6) The DVD player is capable of playing the following types of discs (12 cm or 8 cm diameter): profile 3.0 •...
Page 436
434 UNDERSTANDING YOUR INSTRUMENT PANEL • Other compression formats such as Xvid and RMP4 to the next chapter, or the “Fast Rewind” button to will not play. The Blu-Ray Player will automatically return to the start of the current or previous chapter. skip the file and begin playing the next available file.
Page 437
UNDERSTANDING YOUR INSTRUMENT PANEL 435 • Open sessions are ignored. Only sessions that are you increase the volume level to account for this change in level, remember to lower the volume before changing closed are playable. the disc or to another mode. •...
Page 438
436 UNDERSTANDING YOUR INSTRUMENT PANEL • Mixed disc which contains DivX will be priority • The DVD player always uses the file extension to played on Blu-ray Disc Player. determine the audio format, so MP3 files must always end with the extension .mp3 or .MP3 and WMA If you are still having trouble writing a disc that is files must always end with the extension .wma or playable in the DVD player, check with the disc recording...
Page 439
UNDERSTANDING YOUR INSTRUMENT PANEL 437 • Other compression formats such as AAC, MP3 Pro, Disc Errors Ogg Vorbis, and ATRAC3 will not play. The DVD If the DVD player is unable to read the disc, a Disc Error player will automatically skip the file and begin play- message is displayed on the Radio display and the disc is ing the next available file.
Page 440
438 UNDERSTANDING YOUR INSTRUMENT PANEL The DVD player may shut down during extremely hot Display conditions, such as when the vehicle’s interior tempera- Other Language Setup ture is above 120° F (49° C). The Blu-ray Player may shut down when the vehicle’s interior temperature exceeds 140°...
Page 441
UNDERSTANDING YOUR INSTRUMENT PANEL 439 All of the Language settings have a special Other setting selecting the digit, push the remote control’s Right to accommodate languages other than Japanese or Eng- cursor button to select the next digit. Repeat this digit lish.
Page 442
440 UNDERSTANDING YOUR INSTRUMENT PANEL Rating And Password Setup The default rating is Level 8 (play all discs without a password) and the default password is 0000. The Rating and Password settings work together to control the types of DVDs that your family watches. Most DVD- Video discs have a rating (from 1 to 8) assigned to them where lower numbers are designated for all audiences and higher numbers are designated for more adult audiences.
Page 443
UNDERSTANDING YOUR INSTRUMENT PANEL 441 • After the four-digit password is entered, push the To set the password, activate the DVD Setup Menu and follow these additional instructions: remote control’s ENTER/OK button. If the password is correct, the set password screen is displayed. •...
Page 444
442 UNDERSTANDING YOUR INSTRUMENT PANEL • Using the remote control’s Left and Right cursor buttons, select the Rating tab. • Highlight Change Rating , and then push the remote control’s ENTER/OK button. • Enter the current password. Select a digit, use the remote control’s Up and Down cursor buttons to set the value for the current digit, and then push the remote control’s Right cursor button to select the next...
Page 445
UNDERSTANDING YOUR INSTRUMENT PANEL 443 • THIS PRODUCT IS LICENSED UNDER THE AVC PAT- Product Agreement ENT PORTFOLIO LICENSE FOR THE PERSONAL Software AND NON-COMMERCIAL USE OF A CONSUMER TO This product contains software licensed under GNU (i) ENCODE VIDEO IN COMPLIANCE WITH THE General Public License (GPL) or GNU Lesser General AVC STANDARD ( AVC VIDEO ) AND/OR (ii) DE- Public License (LGPL), etc.
Page 446
444 UNDERSTANDING YOUR INSTRUMENT PANEL CONSUMER ENGAGED IN A PERSONAL AND NON- your mailing address to: Cinavia Consumer Information COMMERCIAL ACTIVITY AND/OR WAS OBTAINED Center, P.O. Box 86851, San Diego, CA, 92138, USA. FROM A VIDEO PROVIDER LICENSED TO PROVIDE This product incorporates proprietary technology under VC-1 VIDEO.
Page 447
UNDERSTANDING YOUR INSTRUMENT PANEL 445 • Manufactured under license under U.S. Patent #’s: device setup menu. Go to vod.divx.com for more infor- 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & mation on how to complete your registration. other U.S. and worldwide patents issued & pending. DivX, DivX Certified and associated logos are trade- DTS is a registered trademark and the DTS logos, marks of Rovi Corporation or its subsidiaries and are...
Page 448
446 UNDERSTANDING YOUR INSTRUMENT PANEL STEERING WHEEL AUDIO CONTROLS — IF The right-hand rocker switch has a pushbutton in the EQUIPPED center, and controls the volume and mode of the sound system. Pushing the top of the rocker switch will increase the volume.
Page 449
UNDERSTANDING YOUR INSTRUMENT PANEL 447 The button located in the center of the left-hand switch CD/DVD/Blu-ray Disc MAINTENANCE will tune to the next preset station that you have pro- To keep a CD/DVD/Blu-ray Disc in good condition, take grammed in the radio preset push-button. the following precautions: CD Player 1.
Page 450
448 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particular General Information disc, it may be damaged (i.e., scratched, reflective coating This device complies with Part 15 of the FCC Rules and removed, a hair, moisture or dew on the disc) oversized, with Industry Canada licence-exempt RSS standard(s).
Page 451
UNDERSTANDING YOUR INSTRUMENT PANEL 449 CLIMATE CONTROLS The primary control for the rear blower is on the front climate control unit located on the instrument panel. The Climate Control system allows you to regulate the When the front control is in any position other than rear, temperature, amount, and direction of air circulating the front control operates all the rear functions.
Page 452
450 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Rear Blower Control — If Equipped Use this control to regulate the amount of air forced through the rear system in any mode you select. The rear blower speed increases as you move the control to the right from the “O”...
Page 453
UNDERSTANDING YOUR INSTRUMENT PANEL 451 5. Right Front Temperature Control NOTE: The air conditioning compressor may operate in Mix and Defrost, even if the A/C button is not pushed. Provides right front seat occupant with independent This dehumidifies the air to help dry the windshield. To temperature control.
Page 454
452 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: CAUTION! (Continued) • You can turn off the heated mirror feature at anytime • Do not use scrapers, sharp instruments, or abrasive by pushing the rear window defroster switch a window cleaners on the interior surface of the second time.
Page 455
UNDERSTANDING YOUR INSTRUMENT PANEL 453 NOTE: 10. Air Conditioning (A/C) Button • If the Recirculation button is pushed when the Push and release to change the current setting. system is in Defrost mode the Recirculation LED The indicator illuminates when ON. indicator will flash three times to indicate Recircula- tion mode is not allowed.
Page 456
454 UNDERSTANDING YOUR INSTRUMENT PANEL 12. Bi-Level Mode Button Economy Mode If ECONOMY mode is desired, push the A/C button to Air is directed through the panel and floor outlets. turn off the indicator light and the A/C compressor. NOTE: There is a difference in temperature (in any Rotate the temperature control knob to the desired tem- conditions other than full cold or full hot), between the perature.
Page 457
UNDERSTANDING YOUR INSTRUMENT PANEL 455 The rear blower and temperature controls for the rear Rear Blower Control seat passengers are located in the headliner, near the The rear blower control knob can be manually set to off, center of the vehicle. or any fixed blower speed, by rotating the knob from low to high.
Page 458
456 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Temperature Control Bi-Level Mode To change the temperature in the rear of the vehicle, Air comes from both the headliner outlets and the rotate the temperature knob counterclockwise to lower floor outlets. the temperature, and clockwise to increase the tempera- NOTE: In many temperature positions, the Bi-Level ture.
Page 459
UNDERSTANDING YOUR INSTRUMENT PANEL 457 • When occupants in the vehicle select the AUTO mode operation, a comfort temperature can be set by using the temperature up and down buttons, and the auto blower operation will be set automatically. • The system can be controlled manually, if desired. •...
Page 460
458 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Blower Control Display 7. Auto Indicator This display shows the current Blower speed selection. This indicates when the system is in Auto mode. 3. Left Front Seat Occupant Temperature Display 8. Right Front Seat Occupant Temperature Display This display shows the temperature setting for the left This display shows the temperature setting for the right front seat occupant.
Page 461
UNDERSTANDING YOUR INSTRUMENT PANEL 459 11. Rear Control Button 14. Auto Temperature Control Button Provides toggle operation between front control screen Controls airflow temperature, distribution, volume, and and rear control screen. Push the button to activate the the amount of air recirculation automatically. Push and rear climate control screen and allow the front seat release to select.
Page 462
460 UNDERSTANDING YOUR INSTRUMENT PANEL 17. Mode Control Button Automatic Temperature Control (ATC) Automatic Operation Push and release to select between Modes (Panel, Bi- Level, Floor, Mix). Performing this function will cause the 1. Push the AUTO button on the front ATC Panel and the ATC to switch into manual mode.
Page 463
UNDERSTANDING YOUR INSTRUMENT PANEL 461 NOTE: Manual Operation Override • It is not necessary to move the temperature settings. This system offers a full complement of manual override features. The AUTO symbol in the front ATC display will The system automatically adjusts the temperature, be turned off when the system is being used in the mode and fan speed to provide comfort as quickly as manual mode.
Page 464
462 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: To change the rear system settings: • If the system is in Mix or Defrost Mode, the A/C can • Push REAR button to change control to rear control be turned off, but the A/C system shall remain active mode, Rear display (below) will appear.
Page 465
UNDERSTANDING YOUR INSTRUMENT PANEL 463 1. Mode Display Bi-Level Mode This display shows the current Mode selection. Air comes from both the headliner outlets and the floor outlets. 2. Rear Temperature Display NOTE: In many temperature positions, the Bi-Level This display shows the temperature setting for the rear mode is designed to provide cooler air out of the head- seat occupants.
Page 466
464 UNDERSTANDING YOUR INSTRUMENT PANEL The rear system temperature control is on the front ATC panel located on the instrument panel. Pushing the Rear Temperature Lock button on the front ATC panel, illuminates a lock symbol in the rear display. The rear temperature and air source are controlled from the front ATC panel.
Page 467
UNDERSTANDING YOUR INSTRUMENT PANEL 465 1. Push the Rear Temperature Lock button on the front NOTE: ATC panel. This turns off the Rear Temperature Lock • It is not necessary to move the temperature settings. icon in the rear temperature knob. The system automatically adjusts the temperature, 2.
Page 468
466 UNDERSTANDING YOUR INSTRUMENT PANEL When rear controls are locked by the front system, the CAUTION! Rear Temperature Lock symbol on the temperature knob is illuminated and any rear overhead adjustments are Interior air enters the Rear Automatic Temperature ignored. Control System through an intake grille, located in the right side trim panel behind the third row seats.
Page 469
UNDERSTANDING YOUR INSTRUMENT PANEL 467 Bi-Level Mode NOTE: In cold weather, use of the Recirculation mode may lead to excessive window fogging. The Recirculation Air comes from both the headliner outlets and the mode is not allowed in Defrost mode to improve window floor outlets.
Page 470
468 UNDERSTANDING YOUR INSTRUMENT PANEL Winter Operation Window Fogging To ensure the best possible heater and defroster perfor- Vehicle windows tend to fog on the inside in mild, rainy mance, make sure the engine cooling system is function- and/or humid weather. To clear the windows, select ing properly and the proper amount, type, and concen- Defrost or Mix mode and increase the front blower speed.
Page 471
UNDERSTANDING YOUR INSTRUMENT PANEL 469 Operating Tips Chart I n f o r ma t i o n P r o v i d e d b y :...
Page 472
I n f o r ma t i o n P r o v i d e d b y :...
Page 473
STARTING AND OPERATING CONTENTS ▫ Key Ignition Park Interlock....483 STARTING PROCEDURES ....475 ▫...
Page 474
472 STARTING AND OPERATING ▫ Electronic Roll Mitigation (ERM) ...513 POWER STEERING .....497 ▫...
Page 475
STARTING AND OPERATING 473 ▫ Run Flat Tires — If Equipped ... . .531 ▫ Reformulated Gasoline ....550 ▫...
Page 477
STARTING AND OPERATING 475 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the reasons. A child or others could be seriously or inside and outside mirrors, fasten your seat belt, and if fatally injured. Children should be warned not to present, instruct all other occupants to buckle their seat touch the parking brake, brake pedal or the trans- belts.
Page 478
476 STARTING AND OPERATING Do not press the accelerator. Use the Fob with Integrated CAUTION! Key to briefly place the ignition in the START position and release it as soon as the starter engages. The starter Damage to the transmission may occur if the follow- motor will continue to run, and it will disengage auto- ing precautions are not observed: •...
Page 479
STARTING AND OPERATING 477 Installing And Removing The ENGINE NOTE: The ENGINE START/STOP button should only START/STOP Button be removed or inserted with the ignition in the OFF position (OFF position for Keyless Enter-N-Go). Installing The Button Normal Starting 1. Remove the Key Fob from the ignition switch. Using The ENGINE START/STOP Button 2.
Page 480
478 STARTING AND OPERATING To Turn Off The Engine Using ENGINE NOTE: If the ignition switch is left in the ACC or RUN START/STOP Button (engine not running) position and the transmission is in PARK, the system will automatically time out after 30 1.
Page 481
STARTING AND OPERATING 479 3. Push the ENGINE START/STOP button a third time to WARNING! (Continued) return the ignition switch to the OFF position. could enter the catalytic converter and once the Extreme Cold Weather (Below –20°F or −29°C) engine has started, ignite and damage the converter and vehicle.
Page 482
480 STARTING AND OPERATING 2. Press the accelerator pedal all the way to the floor and 2. Place the ignition in the START position and release it hold it. as soon as the starter engages. 3. Push and release the ENGINE START/STOP button The starter motor will disengage automatically in 10 once.
Page 483
STARTING AND OPERATING 481 ENGINE BLOCK HEATER — IF EQUIPPED AUTOMATIC TRANSMISSION The engine block heater warms the engine, and permits CAUTION! quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a Damage to the transmission may occur if the follow- grounded, three-wire extension cord.
Page 484
482 STARTING AND OPERATING WARNING! WARNING! (Continued) • Before exiting a vehicle, always apply the parking • It is dangerous to shift out of PARK or NEUTRAL brake, shift the automatic transmission into PARK, if the engine speed is higher than idle speed. If turn the vehicle OFF, remove the key fob from the your foot is not firmly pressing the brake pedal, the ignition and lock your vehicle.
Page 485
STARTING AND OPERATING 483 Key Ignition Park Interlock WARNING! (Continued) This vehicle is equipped with a Key Ignition Park Inter- fully when parked to guard against vehicle move- lock which requires the transmission to be in PARK ment and possible injury or damage. before the ignition switch can be turned to the LOCK/ •...
Page 486
484 STARTING AND OPERATING Brake/Transmission Shift Interlock System This vehicle is equipped with a Brake Transmission Shift Interlock System (BTSI) that holds the shift lever in PARK unless the brakes are applied. To shift the transmission out of PARK, the ignition must be turned to the ON/ RUN position (engine running or not) and the brake pedal must be pressed.
Page 487
STARTING AND OPERATING 485 • The transmission will skip select gears during shifts to The electronically-controlled transmission provides a allow the engine to operate at lower speeds. precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new •...
Page 488
486 STARTING AND OPERATING Only shift from DRIVE to PARK or REVERSE when the NOTE: After selecting any gear range, wait a moment to accelerator pedal is released and the vehicle is stopped. allow the selected gear to engage before accelerating. Be sure to keep your foot on the brake pedal when This is especially important when the engine is cold.
Page 489
STARTING AND OPERATING 487 WARNING! WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL • Never use the PARK position as a substitute for the if the engine speed is higher than idle speed. If parking brake. Always apply the parking brake your foot is not firmly pressing the brake pedal, the fully when parked to guard against vehicle move- vehicle could accelerate quickly forward or in re-...
Page 490
488 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure • Never leave children alone in a vehicle, or with those in or near the vehicle. As with all vehicles, access to an unlocked vehicle. Allowing children to you should never exit a vehicle while the engine is be in a vehicle unattended is dangerous for a running.
Page 491
STARTING AND OPERATING 489 The following indicators should be used to ensure that CAUTION! you have engaged the transmission into the PARK posi- • Before moving the shift lever out of PARK, you tion: must turn the ignition switch from the LOCK/OFF •...
Page 492
490 STARTING AND OPERATING started in this range. Apply the parking brake and shift DRIVE (D) the transmission into PARK if you must leave the vehicle. This range should be used for most city and highway driving. It provides the smoothest upshifts and down- WARNING! shifts, and the best fuel economy.
Page 493
STARTING AND OPERATING 491 During cold temperatures, transmission operation may PARK, REVERSE, and NEUTRAL will continue to oper- be modified depending on engine and transmission ate. The Malfunction Indicator Light (MIL) may be illu- temperature as well as vehicle speed. This feature im- minated.
Page 494
492 STARTING AND OPERATING NOTE: Even if the transmission can be reset, we recom- position, the transmission will operate automatically, mend that you visit your authorized dealer at your shifting between all available gears. Tapping the shift earliest possible convenience. Your authorized dealer has lever to the left (-) will activate ERS mode, display the diagnostic equipment to determine if the problem could current gear in the instrument cluster, and set that gear as...
Page 495
STARTING AND OPERATING 493 Transmission Gear Position Display Actual Gear(s) Allowed 1–2 1–3 1–4 1–5 1–6 1–6 • The engine coolant has reached an adequate tempera- NOTE: To select the proper gear position for maximum deceleration (engine braking), tap the shift lever to the ture.
Page 496
494 STARTING AND OPERATING NOTE: The torque converter clutch will not engage until WARNING! the transmission fluid and engine coolant are warm [usually after 1 to 3 miles (2 to 5 km) of driving]. Because Rapid acceleration on slippery surfaces is dangerous. the engine speed is higher when the torque converter Unequal traction can cause sudden pulling of the clutch is not engaged, it may seem as if the transmission...
Page 497
STARTING AND OPERATING 495 2. Slow down if the road has standing water or puddles. Flowing/Rising Water 3. Replace the tires when tread wear indicators first WARNING! become visible. Do not drive on or across a road or path where water 4.
Page 498
496 STARTING AND OPERATING WARNING! CAUTION! • Driving through standing water limits your vehi- • Always check the depth of the standing water cle’s traction capabilities. Do not exceed 5 mph before driving through it. Never drive through (8 km/h) when driving through standing water. standing water that is deeper than the bottom of •...
Page 499
STARTING AND OPERATING 497 Alternate electric power steering efforts can be selected CAUTION! (Continued) through the Uconnect System. Refer to ”Customer operate the vehicle if any fluid appears contami- Programmable Features” within “Uconnect Settings” in nated, as this may result in further damage. Such “Understanding Your Instrument Panel”...
Page 500
498 STARTING AND OPERATING for service. Refer to “Electronic Vehicle Information Cen- apparent, and/or the system is not functioning as antici- ter (EVIC)” in “Understanding Your Instrument Panel” pated. Coordinate inspection efforts through an autho- for further information. rized dealer. NOTE: CAUTION! •...
Page 501
STARTING AND OPERATING 499 If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, And Genuine Parts” in “Maintaining Your Vehicle” for further informa- tion.
Page 502
500 STARTING AND OPERATING NOTE: WARNING! • When the parking brake is applied and the automatic • When leaving the vehicle, always remove the Key transmission is placed in gear, the “Brake Warning Fob from the ignition and lock your vehicle. Light”...
Page 503
STARTING AND OPERATING 501 WARNING! (Continued) WARNING! (Continued) • Allowing children to be in a vehicle unattended is injury. Also be certain to leave the transmission in dangerous for a number of reasons. A child or PARK. Failure to do so may allow the vehicle to roll others could be seriously or fatally injured.
Page 504
502 STARTING AND OPERATING during application, greater pedal force required to slow Your vehicle may also be equipped with Trailer Sway or stop, and potential activation of the “Brake System Control (TSC). Warning Light”. Electronic Brake Force Distribution (EBD) In the event power assist is lost for any reason (i.e., This function manages the distribution of the braking repeated brake applications with the engine off) the torque between the front and rear axles by limiting...
Page 505
STARTING AND OPERATING 503 come on when the ignition switch is turned to the ON You also may experience the following when ABS acti- position, have the light repaired as soon as possible. vates: • The ABS motor noise (it may continue to run for a Anti-Lock Brake System (ABS) short time after the stop).
Page 506
504 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • The capabilities of an ABS equipped vehicle must can cause possible loss of anti-lock braking capa- never be exploited in a reckless or dangerous bility. Installation of such equipment should be manner that could jeopardize the user’s safety or performed by qualified professionals.
Page 507
STARTING AND OPERATING 505 If the “Anti-Lock Brake Warning Light” is on, the brake unless braking is no longer desired. Once the brake pedal system should be serviced as soon as possible to restore is released, the BAS is deactivated. the benefits of anti-lock brakes.
Page 508
506 STARTING AND OPERATING • The gear selection must match vehicle uphill direction Hill Start Assist (HSA) (i.e., vehicle facing uphill is in forward gear; vehicle The HSA system is designed to mitigate roll back from a backing uphill is in REVERSE gear). complete stop while on an incline.
Page 509
STARTING AND OPERATING 507 WARNING! (Continued) WARNING! (Continued) brake operation to ensure safe operation of the ve- not be enough brake pressure to hold both the hicle under all road conditions. Your complete atten- vehicle and the trailer on a hill when the brake tion is always required while driving to maintain pedal is released.
Page 510
508 STARTING AND OPERATING Disabling And Enabling HSA 4. Start the engine. This feature can be turned on or turned off. To change the 5. Rotate the steering wheel slightly more than one-half current setting, proceed as follows: turn to the left. •...
Page 511
STARTING AND OPERATING 509 Traction Control System (TCS) counteracting the oversteer or understeer condition. En- gine power may also be reduced to help the vehicle This system monitors the amount of wheel spin of each of maintain the desired path. the driven wheels.
Page 512
510 STARTING AND OPERATING Light” begins to flash during acceleration, ease up on the WARNING! (Continued) accelerator and apply as little throttle as possible. Be sure must never be exploited in a reckless or dangerous to adapt your speed and driving to the prevailing road manner which could jeopardize the user’s safety or conditions.
Page 513
STARTING AND OPERATING 511 ESC Operating Modes To enter the “Partial Off” mode, momentarily push the “ESC Off” switch and the “ESC Off Indicator Light” will NOTE: Depending upon model and mode of operation, illuminate. To turn the ESC on again, momentarily push the ESC system may have multiple operating modes.
Page 514
512 STARTING AND OPERATING NOTE: The Electronic Stability Control (ESC) cannot speeds greater than 30 mph (48 km/h), see your autho- prevent the natural laws of physics from acting on the rized dealer as soon as possible to have the problem vehicle, nor can it increase the traction afforded by diagnosed and corrected.
Page 515
STARTING AND OPERATING 513 • The ESC system will make buzzing or clicking sounds road conditions, leaving the roadway, or striking objects when it is active. This is normal; the sounds will stop or other vehicles. when ESC becomes inactive following the maneuver that caused the ESC activation.
Page 516
514 STARTING AND OPERATING is recognized. Note that TSC cannot stop all trailers from TIRE SAFETY INFORMATION swaying. Always use caution when towing a trailer and Tire Markings follow the trailer tongue weight recommendations. Refer to “Trailer Towing” in this section for further informa- tion.
Page 517
STARTING AND OPERATING 515 • Temporary spare tires are designed for temporary NOTE: emergency use only. Temporary high pressure com- • P (Passenger) — Metric tire sizing is based on U.S. pact spare tires have the letter “T” or “S” molded into design standards.
Page 518
516 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on U.S. design standards, or ..blank..= Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 519
STARTING AND OPERATING 517 EXAMPLE: Service Description: 95 = Load Index – A numerical code associated with the maximum load a tire can carry H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions –...
Page 520
518 STARTING AND OPERATING Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on The TIN may be found on one or both sides of the tire, the outboard side, then you will find it on the inboard however, the date code may only be on one side.
Page 521
STARTING AND OPERATING 519 EXAMPLE: DOT MA L9 ABCD 0301 01 = Number representing the year in which the tire was manufactured (two digits) – 01 means the year 2001 – Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.
Page 522
520 STARTING AND OPERATING Term Definition Maximum Inflation Pressure The maximum inflation pressure is the maximum permissible cold tire inflation pressure for this tire. The maximum inflation pressure is molded into the sidewall. Recommended Cold Tire Inflation Pres- Vehicle manufacturer’s recommended cold tire inflation pressure sure as shown on the tire placard.
Page 523
STARTING AND OPERATING 521 Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Example Tire Placard Location (Door) I n f o r ma t i o n P r o v i d e d b y :...
Page 524
522 STARTING AND OPERATING Tire And Loading Information Placard Example Tire Placard Location (B-Pillar) Tire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3.
Page 525
STARTING AND OPERATING 523 4. Cold tire inflation pressures for the front, rear, and To determine the maximum loading conditions of your spare tires. vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or Loading XXX kg”...
Page 526
524 STARTING AND OPERATING 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • If your vehicle will be towing a trailer, load from your “XXX” amount equals 1,400 lbs (635 kg) and there will trailer will be transferred to your vehicle.
Page 527
STARTING AND OPERATING 525 I n f o r ma t i o n P r o v i d e d b y :...
Page 528
526 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
Page 529
STARTING AND OPERATING 527 Fuel Economy WARNING! (Continued) Underinflated tires will increase tire rolling resistance • Unequal tire pressures from one side of the vehicle resulting in higher fuel consumption. to the other can cause the vehicle to drift to the right or left.
Page 530
528 STARTING AND OPERATING At least once a month: (1.6 km) after sitting for a minimum of three hours. The cold tire inflation pressure must not exceed the maximum • Check and adjust tire pressure with a good quality inflation pressure molded into the tire sidewall. pocket-type pressure gauge.
Page 531
STARTING AND OPERATING 529 Tire Pressures For High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds and WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
Page 532
530 STARTING AND OPERATING Consult an authorized tire dealer for tire repairs and Summer Or Three Season Tires — If Equipped additional information. Summer tires provide traction in both wet and dry Damaged Run Flat tires, or Run Flat tires that have conditions, and are not intended to be driven in snow or experienced a loss of pressure should be replaced imme- on ice.
Page 533
STARTING AND OPERATING 531 Snow tires generally have lower speed ratings than what WARNING! was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph Do not use Summer tires in snow/ice conditions. You (120 km/h).
Page 534
532 STARTING AND OPERATING Run Flat tire reaches the run flat mode it has limited CAUTION! driving capabilities and needs to be replaced immedi- ately. A Run Flat tire is not repairable. Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with a It is not recommended driving a vehicle loaded at full compact or limited-use temporary spare installed.
Page 535
STARTING AND OPERATING 533 Compact Spare Tire — If Equipped Do not install more than one compact spare tire and wheel on the vehicle at any given time. The compact spare is for temporary emergency use only. You can identify if your vehicle is equipped with a WARNING! compact spare by looking at the spare tire description on the Tire and Loading Information Placard located on the...
Page 536
534 STARTING AND OPERATING spare tire needs to be replaced. Since it is not the same as WARNING! your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the Limited-use spares are for emergency use only. In- first opportunity.
Page 537
STARTING AND OPERATING 535 Refer to “Freeing A Stuck Vehicle” in “What To Do In Emergencies” for further information. WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one.
Page 538
536 STARTING AND OPERATING worn to the tread wear indicators, the tire should be WARNING! replaced. Refer to “Replacement Tires” in this section for further information. Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to Life Of Tire follow this warning can result in sudden tire failure.
Page 539
STARTING AND OPERATING 537 Information placard or the Vehicle Certification Label for WARNING! the size designation of your tire. The Load Index and • Do not use a tire, wheel size or rating other than Speed Symbol for your tire will be found on the original equipment tire sidewall.
Page 540
538 STARTING AND OPERATING • Install on front tires only. WARNING! (Continued) • Due to limited clearance, a 225/65R17 tire with a • Failure to equip your vehicle with tires having Security Chain Company (SCC) Super Z6 low profile adequate speed capability can result in sudden tire traction device or equivalent is recommended.
Page 541
STARTING AND OPERATING 539 TIRE ROTATION RECOMMENDATIONS CAUTION! (Continued) The tires on the front and rear of your vehicle operate at important that only traction devices in good condi- different loads and perform different steering, driving, tion are used. Broken devices can cause serious and braking functions.
Page 542
540 STARTING AND OPERATING The suggested rotation method is the “forward cross” TIRE PRESSURE MONITOR SYSTEM (TPMS) shown in the following diagram. This rotation pattern The TPMS will warn the driver of a low tire pressure does not apply to some directional tires that must not be based on the cold inflation tire placard pressure require- reversed.
Page 543
STARTING AND OPERATING 541 The TPMS will warn the driver of a low tire pressure if The system will automatically update and the “Tire the tire pressure falls below the low pressure warning Pressure Monitoring Telltale Light” will extinguish once threshold for any reason, including low temperature the updated tire pressures have been received.
Page 544
542 STARTING AND OPERATING have been inflated to the vehicle’s recommended cold tire CAUTION! (Continued) placard pressure value. • After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap. This will prevent CAUTION! moisture and dirt from entering the valve stem, •...
Page 545
STARTING AND OPERATING 543 • The TPMS is not a substitute for proper tire mainte- NOTE: It is particularly important for you to check the nance, and it is the driver’s responsibility to maintain tire pressure in all of your tires regularly and to maintain correct tire pressure, using an accurate tire pressure the proper pressure.
Page 546
544 STARTING AND OPERATING vehicle’s recommended cold tire placard pressure value repeat, providing the system fault still exists. The “Tire (located on the placard label on the driver’s-side B-Pillar). Pressure Monitoring Telltale Light” will turn off when the fault condition no longer exists. A system fault can NOTE: When filling warm tires, the tire pressure may occur with any of the following scenarios: need to be increased up to an additional 4 psi (30 kPa)
Page 547
STARTING AND OPERATING 545 • For each subsequent ignition switch cycle, a chime will Vehicles With Compact Spare sound, the “Tire Pressure Monitoring Telltale Light” • The compact spare tire (if equipped) does not have a will flash on and off for 75 seconds and then remain on TPMS sensor.
Page 548
546 STARTING AND OPERATING Premium System — If Equipped TPMS Low Pressure Warnings The TPMS uses wireless technology with wheel rim- The “Tire Pressure Monitoring Telltale Light” will illumi- mounted electronic sensors to monitor tire pressure lev- nate in the instrument cluster, and an audible chime will els.
Page 549
STARTING AND OPERATING 547 The system will automatically update, the graphic dis- If the ignition switch is cycled, this sequence will repeat, play of the pressure value(s) will stop flashing, and the providing the system fault still exists. If the system fault “Tire Pressure Monitoring Telltale Light”...
Page 550
548 STARTING AND OPERATING The EVIC will also display a “SERVICE TPM SYSTEM” “LOW TIRE” message will be displayed, a chime will message for a minimum of five seconds when a system sound, and the EVIC will still display a flashing fault possibly related to an incorrect sensor location fault pressure value and the Inflate Tire to XX message in is present.
Page 551
STARTING AND OPERATING 549 • Once you repair or replace the original road tire, and NOTE: Changes or modifications not expressly approved reinstall it on the vehicle in place of the compact spare, by the party responsible for compliance could void the the TPMS will update automatically.
Page 552
550 STARTING AND OPERATING making a heavy knocking sound, see your dealer imme- Gasoline/Oxygenate Blends diately. Use of gasoline with an octane number lower Some fuel suppliers blend unleaded gasoline with oxy- than 87 can cause engine failure and may void or not be genates such as ethanol.
Page 553
STARTING AND OPERATING 551 • Poor cold start and cold drivability. Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol • Increased risk for fuel system component corrosion. are not the responsibility of the manufacturer and may void or not be covered under New Vehicle Limited MMT In Gasoline Warranty.
Page 554
552 STARTING AND OPERATING Materials Added To Fuel Fuel System Cautions Besides using unleaded gasoline with the proper octane CAUTION! rating, gasolines that contain detergents, corrosion and stability additives are recommended. Using gasolines Follow these guidelines to maintain your vehicle’s that have these additives will help improve fuel performance: economy, reduce emissions, and maintain vehicle perfor-...
Page 555
STARTING AND OPERATING 553 Carbon Monoxide Warnings CAUTION! (Continued) • The use of fuel additives, which are now being WARNING! sold as octane enhancers, is not recommended. Carbon monoxide (CO) in exhaust gases is deadly. Most of these products contain high concentrations Follow the precautions below to prevent carbon of methanol.
Page 556
554 STARTING AND OPERATING WARNING! (Continued) CAUTION! • Guard against carbon monoxide with proper main- Only vehicles with the E-85 fuel filler door label or a tenance. Have the exhaust system inspected every yellow gas cap can operate on E-85. time the vehicle is raised.
Page 557
STARTING AND OPERATING 555 Fuel Requirements NOTE: • Use seasonally adjusted E-85 fuel (ASTM D5798). With If your vehicle is E-85 compatible, it will operate on unleaded gasoline with any octane rating, or solely E-85 non-seasonally adjusted E-85 fuel, hard starting and fuel, or any mixture of these fuels.
Page 558
556 STARTING AND OPERATING Selection Of Engine Oil For Flexible Fuel Vehicles until the engine is fully warmed up. These issues may be (E-85) And Gasoline Vehicles improved with the use of seasonally adjusted E-85 fuel. FFV vehicles operated on E-85 require specially formu- NOTE: Use of the engine block heater (if equipped) may lated engine oils.
Page 559
STARTING AND OPERATING 557 CAUTION! Replacing fuel system components with non-ethanol compatible components can damage your vehicle. Maintenance CAUTION! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect drivability. Fuel Filler Cap ADDING FUEL NOTE: The driver’s side sliding door cannot be opened...
Page 560
558 STARTING AND OPERATING CAUTION! WARNING! (Continued) • Never add fuel when the engine is running. This is • Damage to the fuel system or emissions control in violation of most state and federal fire regula- system could result from using an improper fuel tions and may cause the MIL to turn on.
Page 561
STARTING AND OPERATING 559 • If the gas cap is not tightened properly, the MIL may VEHICLE LOADING come on. Be sure the gas cap is tightened every time As required by National Highway Traffic Safety Admin- the vehicle is refueled. istration regulations, your vehicle has a certification label affixed to the driver’s side door or B-Pillar.
Page 562
560 STARTING AND OPERATING • Vehicle Identification Number (VIN) WARNING! • Type of Vehicle Because the front wheels steer the vehicle, it is • Month Day and Hour of Manufacture (MDH) important that you do not exceed the maximum front or rear GAWR.
Page 563
STARTING AND OPERATING 561 Inflation Pressure The best way to figure out the total weight of your vehicle is to weigh it when it is fully loaded and ready for This is the cold tire inflation pressure for your vehicle for operation.
Page 564
562 STARTING AND OPERATING have exceeded either GAWR, but the total load is within Common Towing Definitions the specified GVWR, you must redistribute the weight. The following trailer towing related definitions will assist Improper weight distribution can have an adverse effect you in understanding the following information: on the way your vehicle steers and handles and the way Gross Vehicle Weight Rating (GVWR)
Page 565
STARTING AND OPERATING 563 The recommended way to measure GTW is to put your Tongue Weight (TW) fully loaded trailer on a vehicle scale. The entire weight The tongue weight is the downward force exerted on the of the trailer must be supported by the scale. hitch ball by the trailer.
Page 566
564 STARTING AND OPERATING If equipped, the electronic Trailer Sway Control (TSC) steering and brake control thereby enhancing towing recognizes a swaying trailer and automatically applies safety. The addition of a friction/hydraulic sway control individual wheel brakes and/or reduces engine power to also dampens sway caused by traffic and crosswinds and attempt to eliminate the trailer sway.
Page 567
STARTING AND OPERATING 565 Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer Hitch Classification Definitions Class Max.
Page 568
566 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. GCWR (Gross Engine/ Max. GTW (Gross Max. Tongue Combined Weight Frontal Area Transmission Trailer Weight) Weight Rating) 3.6L/Automatic...
Page 569
STARTING AND OPERATING 567 NOTE: The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the Tire and Loading Information placard. Refer to “Tire Safety Information”...
Page 570
568 STARTING AND OPERATING NOTE: Remember that everything put into or on the CAUTION! trailer adds to the load on your vehicle. Also, additional • Do not tow a trailer at all during the first 500 miles factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.
Page 571
STARTING AND OPERATING 569 WARNING! WARNING! (Continued) • Safety chains must always be used between your Improper towing can lead to a collision. Follow these vehicle and trailer. Always connect the chains to guidelines to make your trailer towing as safe as the hook retainers of the vehicle hitch.
Page 572
570 STARTING AND OPERATING • Proper tire inflation pressures are essential to the safe WARNING! (Continued) and satisfactory operation of your vehicle. Refer to • Total weight must be distributed between the tow “Tires – General Information” in “Starting And Oper- vehicle and the trailer such that the following four ating”...
Page 573
STARTING AND OPERATING 571 Towing Requirements — Trailer Brakes WARNING! • Do not interconnect the hydraulic brake system or • Do not connect trailer brakes to your vehicle’s vacuum system of your vehicle with that of the trailer. hydraulic brake lines. It can overload your brake This could cause inadequate braking and possible system and cause it to fail.
Page 574
572 STARTING AND OPERATING CAUTION! (Continued) could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Towing Requirements — Trailer Lights And Wiring Whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for motoring safety.
Page 575
STARTING AND OPERATING 573 Towing Tips Before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Automatic Transmission The DRIVE range can be selected when towing. How- ever, if frequent shifting occurs while in DRIVE, use the Electronic Range Select (ERS) shift control to select a lower gear range.
Page 576
574 STARTING AND OPERATING If you REGULARLY tow a trailer for more than 45 Cooling System minutes of continuous operation, then change the trans- To reduce potential for engine and transmission over- mission fluid and filter as specified for “police, taxi, fleet, heating, take the following actions: or frequent trailer towing”.
Page 577
STARTING AND OPERATING 575 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheels OFF the Ground All Models Flat Tow NONE NOT ALLOWED Dolly Tow Front Rear NOT ALLOWED On Trailer NOTE: When recreational towing your vehicle, always follow applicable state and provincial laws.
Page 578
576 STARTING AND OPERATING Recreational Towing — All Models CAUTION! Recreational towing is allowed ONLY if the front wheels • DO NOT flat tow this vehicle. Damage to the are OFF the ground. This may be accomplished using a drivetrain will result. If this vehicle requires tow- tow dolly or vehicle trailer.
Page 579
WHAT TO DO IN EMERGENCIES CONTENTS HAZARD WARNING FLASHERS ...579 JACKING AND TIRE CHANGING — IF EQUIPPED ......593 IF YOUR ENGINE OVERHEATS .
Page 580
578 WHAT TO DO IN EMERGENCIES ▫ Road Tire Installation ....610 FREEING A STUCK VEHICLE ... . .616 JUMP-STARTING .
Page 581
WHAT TO DO IN EMERGENCIES 579 HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located in the In any of the following situations, you can reduce the lower center area of the instrument panel. potential for overheating by taking the appropriate ac- tion.
Page 582
580 WHAT TO DO IN EMERGENCIES supplement to the radiator and aids in removing heat WARNING! (Continued) from the engine cooling system. do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure CAUTION! cap when the radiator or coolant bottle is hot.
Page 583
WHAT TO DO IN EMERGENCIES 581 2. Turn the two rear left side trim panel latches to release the trim panel. Tire Service Kit Location 1. Open the liftgate. Tire Service Kit I n f o r ma t i o n P r o v i d e d b y :...
Page 584
582 WHAT TO DO IN EMERGENCIES Tire Service Kit Components And Operation Using The Mode Select Knob And Hoses Your Tire Service Kit is equipped with the following symbols to indicate the air or sealant mode. Selecting Air Mode Push in the Mode Select Knob (5) and turn to this position for air pump operation only.
Page 585
WHAT TO DO IN EMERGENCIES 583 Using The Deflation Button Push the Deflation Button (2) to reduce the air pressure in the tire if it becomes over-inflated. Tire Service Kit Usage Precautions • Replace the Tire Service Kit Sealant Bottle (1) and Sealant Hose (6) prior to the expiration date (printed at the lower right hand corner on the bottle label) to assure optimum operation of the system.
Page 586
584 WHAT TO DO IN EMERGENCIES from the vehicle or tire and wheel components. Once WARNING! the sealant dries, it can easily be peeled off and • Do not attempt to seal a tire on the side of the properly discarded. vehicle closest to traffic.
Page 587
WHAT TO DO IN EMERGENCIES 585 WARNING! (Continued) WARNING! (Continued) • Keep Tire Service Kit away from open flames or • Tire Service Kit Sealant solution contains latex. In heat source. case of an allergic reaction or rash, consult a phy- •...
Page 588
586 WHAT TO DO IN EMERGENCIES on the ground. This will provide the best positioning 4. Remove the cap from the valve stem and then screw of the kit when injecting the sealant into the deflated the fitting at the end of the Sealant Hose (6) onto the tire and running the air pump.
Page 589
WHAT TO DO IN EMERGENCIES 587 NOTE: Sealant may leak out through the puncture in the NOTE: If the Mode Select Knob (5) is on Air Mode and tire. the pump is operating, air will dispense from the Air Pump Hose (7) only, not the Sealant Hose (6). If the sealant (white fluid) does not flow within 0 –...
Page 590
588 WHAT TO DO IN EMERGENCIES latch pillar (recommended pressure). Check the tire 3. Immediately disconnect the Sealant Hose (6) from the pressure by looking at the Pressure Gauge (3). valve stem, reinstall the cap on the fitting at the end of the hose, and place the Tire Service Kit in the vehicle If the tire does not inflate to at least 26 psi (1.8 Bar) storage location.
Page 591
WHAT TO DO IN EMERGENCIES 589 (D) Drive Vehicle: (E) After Driving: Immediately after injecting sealant and inflating the tire, Pull over to a safe location. Refer to “Whenever You Stop drive the vehicle 5 miles (8 km) or 10 minutes to ensure to Use Tire Service Kit”...
Page 592
590 WHAT TO DO IN EMERGENCIES If the tire pressure is 19 psi (1.3 Bar) or higher: 5. Remove the Speed Limit sticker from the instrument panel after the tire has been repaired. 1. Push the Power Button (4) to turn on Tire Service Kit and inflate the tire to the pressure indicated on the tire 6.
Page 593
WHAT TO DO IN EMERGENCIES 591 4. Clean any remaining sealant from the Tire Service Kit WHEEL AND TIRE TORQUE SPECIFICATIONS housing. Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Any 5.
Page 594
592 WHAT TO DO IN EMERGENCIES Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Torque Patterns After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated Wheel Mounting Surface against the wheel.
Page 595
WHAT TO DO IN EMERGENCIES 593 WARNING! WARNING! (Continued) under a vehicle that is on a jack. If you need to get To avoid the risk of forcing the vehicle off the jack, under a raised vehicle, take it to a service center do not tighten the lug nuts fully until the vehicle has where it can be raised on a lift.
Page 596
594 WHAT TO DO IN EMERGENCIES Jack Location Spare Tire Removal The jack, jack handle and winch handle tools are stowed The spare tire is stowed inside a protective cover located behind the rear left side trim panel in the rear cargo area. under the center of the vehicle between the front doors by Turn the two cover latches to release the cover.
Page 597
WHAT TO DO IN EMERGENCIES 595 To Access Spare Tire Winch Drive Nut To access the spare tire winch drive nut and lower the spare tire, you will need to refer to one of the following center console configurations. Super Console For vehicles equipped with the Super Console, the spare tire winch assembly drive nut is located beneath the console.
Page 598
596 WHAT TO DO IN EMERGENCIES 2. Open the front drawer to expose the storage compart- Premium/Base/Cargo Center Console ment. Pull the Winch Cover assembly plug (if equipped) to access the winch drive nut. 3. Remove the liner from the console’s storage compart- ment to access the spare tire winch drive nut.
Page 599
WHAT TO DO IN EMERGENCIES 597 Spare Tire Tools The tool pouch contains three pieces and can be as- sembled into a spare tire hook; to remove the compact spare tire/cover assembly from under the vehicle, or a Winch T-handle; to raise/lower the compact spare tire/ cover assembly.
Page 600
598 WHAT TO DO IN EMERGENCIES Spare Tire Removal Instructions The spare tire is located under the vehicle beneath the center console area. Assembling The Spare Tire Hook 1 — Spare Tire Hook/T-handle 2 — Extension 1 3 — Extension 2 Spare Tire And Cover 1.
Page 601
WHAT TO DO IN EMERGENCIES 599 2. Rotate the nut to the left until the winch mechanism stops turning freely. This will allow enough slack in the cable to allow you to pull the spare tire out from underneath the vehicle. CAUTION! The winch mechanism is designed for use with the winch T-handle only.
Page 602
600 WHAT TO DO IN EMERGENCIES 4. Stand the tire/cover assembly upright and remove the Preparations For Jacking wheel spacer by squeezing the winch retaining tabs 1. Park the vehicle on a firm, level surface. Avoid ice or together. Push the retainer through the spare tire to slippery areas.
Page 603
WHAT TO DO IN EMERGENCIES 601 6. Block both the front and rear of the wheel diagonally WARNING! (Continued) opposite of the jacking position. For example, if chang- • Block the wheel diagonally opposite the wheel to ing the right front tire, block the left rear wheel. be raised.
Page 604
602 WHAT TO DO IN EMERGENCIES NOTE: Refer to the “Compact Spare Tire” section of WARNING! (Continued) “Tires – General Information” for information about the • To assure that compact spare tires, flat or inflated, compact spare tire, its use, and operation. are securely stowed, compact spares must be 1.
Page 605
WHAT TO DO IN EMERGENCIES 603 Jack Locations Rear Jacking Locations CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated. Rear jack locations are between a pair of down-facing tabs on the sill flange of the vehicle side body. I n f o r ma t i o n P r o v i d e d b y :...
Page 606
604 WHAT TO DO IN EMERGENCIES Rear Jack Engaged Front Jack Locations Front jack location is on the sill flange of the vehicle body and is located 6 inches (150 mm) from door edge. I n f o r ma t i o n P r o v i d e d b y :...
Page 607
WHAT TO DO IN EMERGENCIES 605 WARNING! Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.
Page 608
606 WHAT TO DO IN EMERGENCIES WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the wheel lug nuts, for vehicles with wheel covers, remove the cover from the wheel by hand.
Page 609
WHAT TO DO IN EMERGENCIES 607 WARNING! WARNING! To avoid the risk of forcing the vehicle off the jack, A loose tire or jack thrown forward in a collision or do not tighten the wheel nuts fully until the vehicle hard stop could endanger the occupants of the ve- has been lowered.
Page 610
608 WHAT TO DO IN EMERGENCIES NOTE: Refer to the “Spare Tire Tools” section for instruc- WARNING! tions on assembling the T-handle. A loose compact spare tire/cover assembly, thrown 12. Stow the jack, jack handle and winch handle tools forward in a collision or hard stop could endanger back in the stowage compartment.
Page 611
WHAT TO DO IN EMERGENCIES 609 3. Turn the compact spare tire so that the valve stem is WARNING! down, and place the tire into the compact spare tire/ cover assembly. Slide the wheel spacer through the Verify that both retainer tabs of the wheel spacer center of the wheel and compact spare tire/cover assem- have been properly extended through the center of bly, so that the two retainer tabs snap out and engage the...
Page 612
610 WHAT TO DO IN EMERGENCIES CAUTION! The winch mechanism is designed specifically to stow a compact spare tire only. Do not attempt to use the winch to stow the full size deflated tire, or any other full-size tire, as the tire may not be held securely.
Page 613
WHAT TO DO IN EMERGENCIES 611 snapping the cover over the two lug nuts. Do not use 7. After 25 miles (40 km) check the lug nut torque with a a hammer or excessive force to install the cover. torque wrench to ensure that all lug nuts are properly seated against the wheel.
Page 614
612 WHAT TO DO IN EMERGENCIES 4. Refer to “Torque Specifications” in this section for CAUTION! proper wheel lug nut torque. Do not use a portable battery booster pack or any 5. After 25 miles (40 km) check the lug nut torque with a other booster source with a system voltage greater torque wrench to ensure that all lug nuts are properly than 12 Volts or damage to the battery, starter motor,...
Page 615
WHAT TO DO IN EMERGENCIES 613 Preparations For Jump-Start WARNING! The battery in your vehicle is located on the left side of • Take care to avoid the radiator cooling fan when- the engine compartment. ever the hood is raised. It can start anytime the ignition switch is ON.
Page 616
614 WHAT TO DO IN EMERGENCIES 3. If using another vehicle to jump-start the battery, park CAUTION! the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. Failure to follow these procedures could result in damage to the charging system of the booster vehicle WARNING! or the discharged vehicle.
Page 617
WHAT TO DO IN EMERGENCIES 615 4. Connect the opposite end of the negative (-) jumper 6. Once the engine is started, remove the jumper cables cable to a good engine ground (exposed metal part of in the reverse sequence: the discharged vehicle’s engine) away from the battery Disconnecting The Jumper Cables and the fuel injection system.
Page 618
616 WHAT TO DO IN EMERGENCIES maintain the rocking motion, without spinning the CAUTION! wheels or racing the engine. Accessories plugged into the vehicle power outlets CAUTION! draw power from the vehicle’s battery, even when not in use (i.e., cellular devices, etc.). Eventually, if Racing the engine or spinning the wheels may lead to plugged in long enough without engine operation, transmission overheating and failure.
Page 619
WHAT TO DO IN EMERGENCIES 617 CAUTION! WARNING! (Continued) explode and injure someone. Do not spin your vehi- • When “rocking” a stuck vehicle by shifting be- cle’s wheels faster than 30 mph (48 km/h) or for tween DRIVE and REVERSE, do not spin the longer than 30 seconds continuously without stop- wheels faster than 15 mph (24 km/h), or drivetrain ping when you are stuck and do not let anyone near...
Page 620
618 WHAT TO DO IN EMERGENCIES 3. Using a small screwdriver or similar tool, remove the 5. Insert the screwdriver or similar tool into the access shift lever override access cover (located near the top hole, and push and hold the override release lever right of the shift lever in the instrument panel).
Page 621
WHAT TO DO IN EMERGENCIES 619 TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service. Towing Condition Wheels OFF the Ground ALL MODELS Flat Tow NONE If transmission is operable: • Transmission in NEUTRAL Wheel lift Rear •...
Page 622
620 WHAT TO DO IN EMERGENCIES • The towing speed must not exceed 25 mph (40 km/h). CAUTION! If the transmission is not operable, or the vehicle must • Do not use sling type equipment when towing. be towed faster than 25 mph (40 km/h) or farther than 15 Vehicle damage may occur.
Page 623
MAINTAINING YOUR VEHICLE CONTENTS ▫ Engine Air Cleaner Filter ....631 ENGINE COMPARTMENT — 3.6L ..623 ▫ Exhaust System ..... .632 ONBOARD DIAGNOSTIC SYSTEM —...
Page 624
622 MAINTAINING YOUR VEHICLE ▫ Appearance Care And Protection From ▫ Front Side Marker Lamp ....668 Corrosion ......650 ▫...
Page 626
624 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated Onboard • Prolonged driving with the MIL on could cause Diagnostic system called OBD II. This system monitors further damage to the emission control system. It the performance of the emissions, engine, and automatic could also affect fuel economy and driveability.
Page 627
MAINTAINING YOUR VEHICLE 625 “Electronic Vehicle Information Center (EVIC)” in “Un- EMISSIONS INSPECTION AND MAINTENANCE derstanding Your Instrument Panel” for further informa- PROGRAMS tion. Tighten the gas cap until a “clicking” sound is In some localities, it may be a legal requirement to pass heard.
Page 628
626 MAINTAINING YOUR VEHICLE Your vehicle has a simple ignition actuated test, which the ignition or start the engine. This means that your you can use prior to going to the test station. To check if vehicle’s OBD II system is not ready and you should your vehicle’s OBD II system is ready, you must do the not proceed to the I/M station.
Page 629
MAINTAINING YOUR VEHICLE 627 before going to the I/M station. The I/M station can fail NOTE: Intentional tampering with emissions control your vehicle because the MIL is on with the engine systems may void your warranty and could result in civil running.
Page 630
628 MAINTAINING YOUR VEHICLE Besides those maintenance items specified in the fixed CAUTION! (Continued) “Maintenance Schedule”, there are other components transmission, or air conditioning. Such damage is which may require servicing or replacement in the future. not covered by the New Vehicle Limited Warranty. If a flush is needed because of component malfunc- CAUTION! tion, use only the specified fluid for the flushing...
Page 631
MAINTAINING YOUR VEHICLE 629 dipstick. Adding one quart of oil when the reading is at Engine Oil Selection the MIN mark will result in a MAX reading on these For best performance and maximum protection under all engines. types of operating conditions, the manufacturer only recommends engine oils that are API Certified and meet CAUTION! the requirements of FCA Material Standard MS-6395.
Page 632
630 MAINTAINING YOUR VEHICLE NOTE: MOPAR SAE 5W-30 engine oil approved to FCA CAUTION! Material Standard MS-6395 such as Pennzoil, Shell Helix or equivalent may be used when SAE 5W-20 engine oil Do not use chemical flushes in your engine oil as the meeting MS-6395 is not available.
Page 633
MAINTAINING YOUR VEHICLE 631 Materials Added To Engine Oil Engine Oil Filter Selection The manufacturer strongly recommends against the ad- This manufacturer’s engines have a full-flow type oil dition of any additives (other than leak detection dyes) to filter. Use a filter of this type for replacement. The quality the engine oil.
Page 634
632 MAINTAINING YOUR VEHICLE Exhaust System WARNING! (Continued) The best protection against carbon monoxide entry into cleaner, hoses, etc.) unless such removal is necessary the vehicle body is a properly maintained engine exhaust for repair or maintenance. Make sure that no one is system.
Page 635
MAINTAINING YOUR VEHICLE 633 WARNING! CAUTION! • Exhaust gases can injure or kill. They contain • The catalytic converter requires the use of un- carbon monoxide (CO), which is colorless and leaded fuel only. Leaded gasoline will destroy the odorless. Breathing it can make you unconscious effectiveness of the catalyst as an emissions control and can eventually poison you.
Page 636
634 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter dam- verter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage.
Page 637
MAINTAINING YOUR VEHICLE 635 WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can • It is essential when replacing the cables on the burn or even blind you. Do not allow battery fluid battery that the positive cable is attached to the to contact your eyes, skin, or clothing.
Page 638
636 MAINTAINING YOUR VEHICLE cleaning of the condenser fins and a performance test. CAUTION! Drive belt tension should also be checked at this time. Do not use chemical flushes in your air conditioning WARNING! system as the chemicals can damage your air condi- tioning components.
Page 639
MAINTAINING YOUR VEHICLE 637 A/C Air Filter 4. Disengage the two retaining tabs that secure the filter cover to the HVAC housing, and remove the cover. Refer to the “Maintenance Schedule” for the proper maintenance intervals. WARNING! Do not remove the A/C air filter while the blower is operating or personal injury may result.
Page 640
638 MAINTAINING YOUR VEHICLE 6. Install the A/C air filter with the arrow on the filter operation and to protect against rust and wear. Prior to pointing toward the floor. When installing the filter the application of any lubricant, the parts concerned cover, make sure the retaining tabs fully engage the should be wiped clean to remove dust and grit;...
Page 641
MAINTAINING YOUR VEHICLE 639 Operation of the wipers on dry glass for long periods Fill the reservoir with windshield washer solvent (not may cause deterioration of the wiper blades. Always use radiator antifreeze) and operate the system for a few washer fluid when using the wipers to remove salt or dirt seconds to flush out any residual water.
Page 642
640 MAINTAINING YOUR VEHICLE with water as directed on the container, aids cleaning Coolant Checks action, reduces the freezing point to avoid line clogging, Check the engine coolant (antifreeze) protection every 12 and is not harmful to paint or trim. months (before the onset of freezing weather, where applicable).
Page 643
MAINTAINING YOUR VEHICLE 641 If the cap is sealing properly, the engine coolant (anti- Selection Of Coolant freeze) will begin to drain from the coolant recovery Refer to “Fluids, Lubricants, And Genuine Parts” in bottle. DO NOT REMOVE THE COOLANT PRESSURE “Maintaining Your Vehicle”...
Page 644
642 MAINTAINING YOUR VEHICLE miles (240,000 km) before replacement. To prevent reduc- CAUTION! (Continued) ing this extended maintenance period, it is important that OAT coolant (conforming to MS.90032), by an au- you use the same engine coolant (OAT coolant conform- thorized dealer as soon as possible.
Page 645
MAINTAINING YOUR VEHICLE 643 • Use only high purity water such as distilled or deion- HOAT and OAT coolant are mixed in an emergency, ized water when mixing the water/engine coolant have a authorized dealer drain, flush, and refill with (antifreeze) solution.
Page 646
644 MAINTAINING YOUR VEHICLE puddles on the ground. If ingested by a child or pet, seek WARNING! (Continued) emergency assistance immediately. Clean up any ground an overheated engine. Heat causes pressure to spills immediately. build up in the cooling system. To prevent scalding Coolant Level or injury, do not remove the pressure cap while the system is hot or under pressure.
Page 647
MAINTAINING YOUR VEHICLE 645 • Check the coolant freeze point in the radiator and in the When additional engine coolant (antifreeze) is needed to maintain the proper level, only OAT coolant that meets coolant expansion bottle. If engine coolant (antifreeze) the requirements of FCA Material Standard MS.90032 needs to be added, the contents of the coolant expansion should be added to the coolant bottle.
Page 648
646 MAINTAINING YOUR VEHICLE • Do not change the thermostat for Summer or Winter WARNING! (Continued) operation. If replacement is ever necessary, install high brake temperatures, excessive lining wear, and ONLY the correct type thermostat. Other designs may possible brake damage. You would not have your full result in unsatisfactory engine coolant (antifreeze) braking capacity in an emergency.
Page 649
MAINTAINING YOUR VEHICLE 647 brakes, fluid level can be expected to fall as the brake WARNING! (Continued) pads wear. However, low fluid level may be caused by a • To avoid contamination from foreign matter or leak and a checkup may be needed. moisture, use only new brake fluid or fluid that has Use only manufacturer’s recommended brake fluid.
Page 650
648 MAINTAINING YOUR VEHICLE WARNING! (Continued) CAUTION! • Do not allow petroleum based fluid to contaminate Using a transmission fluid other than the manufac- the brake fluid. Brake seal components could be turer’s recommended fluid may cause deterioration damaged, causing partial or complete brake failure. in transmission shift quality and/or torque converter This could result in a collision.
Page 651
MAINTAINING YOUR VEHICLE 649 use of special dyes for diagnosing fluid leaks. Avoid using your authorized dealer immediately to have the trans- transmission sealers as they may adversely affect seals. mission fluid level checked. Operating the vehicle with an improper fluid level can cause severe transmission CAUTION! damage.
Page 652
650 MAINTAINING YOUR VEHICLE Appearance Care And Protection From Corrosion What Causes Corrosion? Corrosion is the result of deterioration or removal of Protection Of Body And Paint From Corrosion paint and protective coatings from your vehicle. Vehicle body care requirements vary according to geo- graphic locations and usage.
Page 653
MAINTAINING YOUR VEHICLE 651 • If insects, tar, or other similar deposits have accumu- Special Care lated on your vehicle, use MOPAR Super Kleen Bug • If you drive on salted or dusty roads or if you drive and Tar Remover to remove. near the ocean, hose off the undercarriage at least once •...
Page 654
652 MAINTAINING YOUR VEHICLE • If you carry special cargo such as chemicals, fertilizers, • For aluminum wheels, use MOPAR Wheel Cleaner or de-icer salt, etc., be sure that such materials are well equivalent. packaged and sealed. CAUTION! • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.
Page 655
MAINTAINING YOUR VEHICLE 653 • Blot any remaining stain with a clean, damp towel. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt • For tough stains, apply MOPAR Total Clean, or a mild can act as an abrasive and damage the leather upholstery soap solution to a clean, damp cloth and remove stain.
Page 656
654 MAINTAINING YOUR VEHICLE Cleaning Headlights CAUTION! Your vehicle is equipped with plastic headlights and fog Direct contact of air fresheners, insect repellents, lights that are lighter and less susceptible to stone break- suntan lotions, or hand sanitizers to the plastic, age than glass headlights.
Page 657
MAINTAINING YOUR VEHICLE 655 Glass Surfaces 1. Clean with a wet soft cloth. A mild soap solution may be used, but do not use high alcohol content or All glass surfaces should be cleaned on a regular basis abrasive cleaners. If soap is used, wipe clean with a with MOPAR Glass Cleaner, or any commercial clean damp cloth.
Page 658
656 MAINTAINING YOUR VEHICLE Cleaning WARNING! The liner is top shelf dishwasher safe, or you may follow A frayed or torn belt could rip apart in a collision and the cleaning procedure below. leave you with no protection. Inspect the belt system Soak the liner in a mixture of medium hot tap water and periodically, checking for cuts, frays, or loose parts.
Page 659
MAINTAINING YOUR VEHICLE 657 FUSES WARNING! (Continued) • If a general protection fuse for safety systems (air WARNING! bag system, braking system), power unit systems • When replacing a blown fuse, always use an appro- (engine system, gearbox system) or steering system priate replacement fuse with the same amp rating as blows, contact an authorized dealer.
Page 660
658 MAINTAINING YOUR VEHICLE CAUTION! • When installing the Totally Integrated Power Mod- ule cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure.
Page 661
MAINTAINING YOUR VEHICLE 659 Cavity Cartridge Fuse Mini-Fuse Description 40 Amp Green – Power Folding Seat 30 Amp Pink – Power Liftgate Module 30 Amp Pink – Rear Door Module 25 Amp Clear – Driver Door Node 25 Amp Clear –...
Page 662
660 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description 60 Amp Yellow – Ignition Off Draw (IOD) – Main 40 Amp Green – Rear Window Defogger 40 Amp Green – Front Blower 40 Amp Green – Starter Solenoid 20 Amp Blue –...
Page 663
MAINTAINING YOUR VEHICLE 661 Cavity Cartridge Fuse Mini-Fuse Description – 20 Amp Yellow Power Outlet #2 (BATT/ACC SELECT) – Center Seat or with Console Rear – 20 Amp Yellow Front Heated Seat – If Equipped – 20 Amp Yellow Rear Heated Seat – If Equipped –...
Page 664
662 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description – 15 Amp Blue Left Tail/License/Park Lamp, Running Lamps – 15 Amp Blue Right Tail/Park/Run Lamp – 25 Amp Clear Powertrain – 15 Amp Blue Instrument Cluster Interior Light, Switch Bank, Steering Column Module, Switch Steering Wheel –...
Page 665
MAINTAINING YOUR VEHICLE 663 Cavity Cartridge Fuse Mini-Fuse Description – 20 Amp Yellow Back-Up Lamps – 10 Amp Red Airbag Module, THATCHUM – If Equipped – 10 Amp Red Powertrain – 10 Amp Red Park Assist, Heater Climate Control Module, Head- lamp Wash, Compass, Rear Camera, Door Lamps, Flashlight, Relay Diesel Cabin Heater –...
Page 666
664 MAINTAINING YOUR VEHICLE • Or, disconnect the negative cable from the battery. VEHICLE STORAGE • Anytime you store your vehicle, or keep it out of If you are leaving your vehicle dormant for more than 21 days, you may want to take steps to protect your battery. service for two weeks or more, run the air conditioning You may do the following: system at idle for about five minutes in the fresh air...
Page 667
MAINTAINING YOUR VEHICLE 665 Bulb Number Overhead Console Reading Lamps PC579 Removable Console Lamp – If Equipped Visor Vanity Lamps 6501966 NOTE: For lighted switches, see your authorized dealer for replacement instructions. Exterior Bulbs Bulb Number Headlamp – (Low and High Beam Halogen) H11LL Headlamp (HID –...
Page 668
666 MAINTAINING YOUR VEHICLE Bulb Number Center High-Mounted Stop Lamp LED (Serviced at Authorized Dealer) Backup Lamp 3157 License yourself. If a headlamp bulb fails, take your vehicle to BULB REPLACEMENT an authorized dealer for service. NOTE: Lens fogging can occur under certain atmo- spheric conditions.
Page 669
MAINTAINING YOUR VEHICLE 667 NOTE: On vehicles equipped with High Intensity Dis- CAUTION! charge (HID) headlamps, when the headlamps are turned on, there is a blue hue to the lamps. This dimin- Do not touch the new bulb with your fingers. Oil ishes and becomes more white after approximately 10 contamination will severely shorten bulb life.
Page 670
668 MAINTAINING YOUR VEHICLE Front Side Marker Lamp 1. From behind the bumper fascia, or the access panel on the air dam, twist the bulb counterclockwise, and 1. Raise the hood to access the rear of the headlamp remove bulb. housing.
Page 671
MAINTAINING YOUR VEHICLE 669 2. Remove the tail lamp assembly by removing the two NOTE: screws from the inboard side. Use a fiber stick or • If a screwdriver is used, make sure a soft material is similar tool to gently pry the light on the outboard side placed between the vehicle body and tool so not to to disengage the two ball studs.
Page 672
670 MAINTAINING YOUR VEHICLE License Lamp 2. Twist and remove the socket from the lamp assembly and pull the bulb out to remove. The license plate lamp is located under the tailgate light bar and above the license plate. 3. Push the bulb into the socket, twist the socket into the lamp assembly and reinstall the lamp assembly into 1.
Page 673
MAINTAINING YOUR VEHICLE 671 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) meeting the requirements of FCA Material Standard MS.90032. Engine Oil We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the require- ments of FCA Material Standard MS-6395 such as MOPAR, Pennzoil, and Shell Helix.
Page 674
672 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! (Continued) • Do not use water alone or alcohol-based engine • Mixing of engine coolant (antifreeze) other than coolant (antifreeze) products. Do not use additional specified Organic Additive Technology (OAT) en- rust inhibitors or antirust products, as they may not gine coolant (antifreeze), may result in engine be compatible with the radiator engine coolant and damage and may decrease corrosion protection.
Page 675
MAINTAINING YOUR VEHICLE 673 Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Use Only ATF+4 Automatic Transmission Fluid. Failure to use ATF+4 fluid may affect the function or perfor- mance of your transmission. We recommend MOPAR ATF+4 Fluid. Brake Master Cylinder We recommend you use MOPAR DOT 3.
Page 676
I n f o r ma t i o n P r o v i d e d b y :...
MAINTENANCE SCHEDULES CONTENTS ▫ Maintenance Chart ....678 MAINTENANCE SCHEDULE ....676 I n f o r ma t i o n P r o v i d e d b y :...
Page 678
676 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE than your authorized dealer, the message can be reset by referring to the steps described under “Electronic Vehicle Your vehicle is equipped with an automatic oil change Information Center (EVIC)” in “Understanding Your indicator system. The oil change indicator system will Instrument Panel”...
Page 679
MAINTENANCE SCHEDULES 677 • Check tire pressure and look for unusual wear or • Check function of all interior and exterior lights. damage. Rotate tires at the first sign of irregular wear, Required Maintenance Intervals. even if it occurs before the oil indicator system turns on. Refer to the maintenance schedules on the following •...
Page 680
678 MAINTENANCE SCHEDULES Maintenance Chart Refer to the Maintenance Schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, boot seals, and replace if necessary.
Page 681
MAINTENANCE SCHEDULES 679 Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Replace spark plugs (3.6L engine). ** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first. Change automatic transmission fluid and filter if using your vehicle for any of the following: police, taxi, fleet, or frequent trailer towing.
Page 682
680 MAINTENANCE SCHEDULES WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 683
IF YOU NEED CONSUMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE ..... . .683 Speech Impaired (TDD/TTY) .
Page 684
682 IF YOU NEED CONSUMER ASSISTANCE ▫ Traction Grades ..... . .689 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES ..689 ▫...
Page 685
IF YOU NEED CONSUMER ASSISTANCE 683 SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 686
684 IF YOU NEED CONSUMER ASSISTANCE • Authorized dealer name facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized FCA US LLC Customer Center dealer service manager first.
Page 687
1-800-380-CHRY. Puerto Rico And U.S. Virgin Islands Canadian residents with hearing difficulties that require Customer Service Chrysler International Services LLC assistance can use the special needs relay service offered P.O. Box 191857 by Bell Canada. For TTY teletypewriter users, dial 711...
Page 688
686 IF YOU NEED CONSUMER ASSISTANCE Warranty expires. The manufacturer stands behind only We appreciate that you have made a major investment the manufacturer’s service contracts. If you purchased a when you purchased the vehicle. An authorized dealer manufacturer’s service contract, you will receive Plan has also made a major investment in facilities, tools, and Provisions and an Owner Identification Card in the mail training to assure that you are absolutely delighted with...
Page 689
IF YOU NEED CONSUMER ASSISTANCE 687 WARRANTY INFORMATION If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in See the Warranty Information Booklet, located on the a group of vehicles, it may order a recall and remedy DVD, for the terms and provisions of FCA US LLC campaign.
Page 690
688 IF YOU NEED CONSUMER ASSISTANCE Canada, Motor Vehicle Defect Investigations and Recalls at and/or components is written in straightforward lan- 1-800-333-0510 or go to http://www.tc.gc.ca/roadsafety/ guage with illustrations, diagrams, and charts. Diagnostic Procedure Manuals PUBLICATION ORDER FORMS Diagnostic Procedure Manuals are filled with diagrams, To order the following manuals, you may use either the charts and detailed illustrations.
Page 691
IF YOU NEED CONSUMER ASSISTANCE 689 Call toll free at: Treadwear • 1-800-890-4038 (U.S.) The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled • 1-800-387-1143 (Canada) conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded Visit us on the Worldwide Web at:...
Page 692
690 IF YOU NEED CONSUMER ASSISTANCE excessive temperature can lead to sudden tire failure. The WARNING! grade C corresponds to a level of performance, which all passenger vehicle tires must meet under the Federal The traction grade assigned to this tire is based on Motor Vehicle Safety Standard No.
Page 693
INDEX I n f o r ma t i o n P r o v i d e d b y :...
Page 694
692 INDEX About Your Brakes ......501 Maintaining Your Air Bag System ... .97 Adding Engine Coolant (Antifreeze) .
Page 695
INDEX 693 Disarm The System ..... . .19 Adding Fluid ......649 Tamper Alert .
Page 696
694 INDEX Brake Control System, Electronic ....502 Cargo Compartment Brake Fluid ......673 Luggage Carrier .
Page 697
INDEX 695 Infants And Child Restraints ....101 Compass Variance ......358 Install A LATCH-Compatible Child Restraint .
Page 698
696 INDEX Points To Remember .....645 Power Steering ......498 Pressure Cap .
Page 710
708 INDEX Speed Control (Cruise Control)....242 Stow N Go (Fold in Floor) Seats ....200 Starting .
Page 711
INDEX 709 General Information ....526, 532 Tire Safety Information .....514 High Speed .
Page 712
710 INDEX Tips ....... . .573 Uconnect 130 Trailer And Tongue Weight ....567 Operating Instructions Auxiliary Mode .
Page 713
INDEX 711 Vehicle Certification Label ....559 Water Vehicle Identification Number (VIN) ... . .6 Driving Through .
Page 714
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
Need help?
Do you have a question about the 2016 Town & Country and is the answer not in the manual?
Questions and answers