Page 1 Pacifica 2 0 1 7 O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA This manual illustrates and describes the operation of With respect to any Vehicles Sold in Canada, the name FCA features and equipment that are either standard or op- US LLC shall be deemed to be deleted and the name FCA tional on this vehicle.
Page 3 TABLE OF CONTENTS SECTION PAGE INTRODUCTION ............. . . 3 GRAPHICAL TABLE OF CONTENTS .
Page 5 INTRODUCTION CONTENTS ▫ Symbols......4 INTRODUCTION ......4 HOW TO USE THIS MANUAL .
Page 6: Introduction 3
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained tech- Congratulations on selecting your new FCA US LLC nicians and genuine MOPAR® parts, and cares about vehicle. Be assured that it represents precision workman- your satisfaction.
Page 7: Introduction
INTRODUCTION...
Page 8: Warnings And Cautions
6 INTRODUCTION WARNINGS AND CAUTIONS VEHICLE MODIFICATIONS/ALTERATIONS This Owner’s Manual contains WARNINGS against WARNING! operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against proce- Any modifications or alterations to this vehicle could dures that could result in damage to your vehicle. If you seriously affect its roadworthiness and safety and do not read this entire Owner’s Manual, you may miss may lead to a collision resulting in serious injury or...
Page 9 GRAPHICAL TABLE OF CONTENTS CONTENTS FRONT VIEW ......8 INTERIOR ......11 REAR VIEW .
Page 10 8 GRAPHICAL TABLE OF CONTENTS FRONT VIEW Front View 1 — Hood/Engine Compartment 4 — Doors 2 — Windshield 5 — Wheels/Tires 3 — Exterior Mirrors 6 — Headlights...
Page 11 GRAPHICAL TABLE OF CONTENTS 9 REAR VIEW Rear View 1 — Rear Lights 2 — Rear Windshield Wiper 3 — Liftgate...
Page 12 10 GRAPHICAL TABLE OF CONTENTS INSTRUMENT PANEL Instrument Panel 1 — Air Vents 5 — Glove/Storage Compartment 2 — Multifunction Lever 6 — Ignition 3 — Instrument Cluster 7 — Steering Wheel 4 — Windshield Wiper Lever 8 — Headlight Switch...
Page 13 GRAPHICAL TABLE OF CONTENTS 11 INTERIOR Interior Features 1 — Power Window/Door Lock Switches 5 — Door handle 2 — Electronic Gear Selector 6 — Climate Control 3 — Uconnect Radio 7 — Center Console 4 — Switch Panel 8 — Seats...
Page 15: Table Of Contents
GETTING TO KNOW YOUR VEHICLE CONTENTS ▫ To Exit Remote Start Mode And Drive The KEYS ....... .19 Vehicle .
Page 16 14 GETTING TO KNOW YOUR VEHICLE ▫ To Disarm The System ....39 ▫ Manual Adjustment (Front Seats) ...59 ▫...
Page 17 GETTING TO KNOW YOUR VEHICLE 15 ▫ Power Folding Third Row Head Restraints — If ▫ Tilt Mirrors In Reverse (Available With Memory Equipped ......101 Seat Only) —...
Page 18 16 GETTING TO KNOW YOUR VEHICLE ▫ Multifunction Lever ....113 ▫ Windshield Washers....121 ▫...
Page 19 GETTING TO KNOW YOUR VEHICLE 17 ▫ Opening Sunroof ..... .154 ▫ Power Liftgate — If Equipped ... .163 ▫...
Page 20 18 GETTING TO KNOW YOUR VEHICLE ▫ Sun Screens — If Equipped ....193 ▫ Overhead Storage With Sunglass Storage ..200 ▫ Power Outlets ..... . .194 ROOF LUGGAGE RACK —...
Page 21: Keys
GETTING TO KNOW YOUR VEHICLE 19 KEYS NOTE: The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE Key The keyless ignition system consists of a Key Fob with Fob go dead. The emergency key is also for locking/ Remote Keyless Entry (RKE) transmitter (RKE Key Fob) unlocking the glove compartment.
Page 22 20 GETTING TO KNOW YOUR VEHICLE Four Button RKE Key Fob Five Button RKE Key Fob...
Page 23 GETTING TO KNOW YOUR VEHICLE 21 Six Button RKE Key Fob Seven Button RKE Key Fob...
Page 24 22 GETTING TO KNOW YOUR VEHICLE General Information To Unlock The Doors The following regulatory statement applies to all radio NOTE: Uconnect Settings lets you program the system frequency (RF) devices equipped in this vehicle: to unlock either the driver’s side doors on the first push (default) or unlock all doors on the first push of the This device complies with Part 15 of the FCC Rules and UNLOCK button on the RKE Key Fob.
Page 25 GETTING TO KNOW YOUR VEHICLE 23 2nd Push Of Key Fob Unlocks Push and release the UNLOCK button on the RKE Key Fob twice within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal.
Page 26 24 GETTING TO KNOW YOUR VEHICLE This feature lets you program the system to unlock either the driver’s door or all doors on the first push of the UNLOCK button on the RKE Key Fob. To change the current setting, refer to “Uconnect Settings” in “Multime- dia”...
Page 27 GETTING TO KNOW YOUR VEHICLE 25 To remove the emergency key, press the mechanical Key Fob With Remote Control And Integrated Vehicle button on the side of the RKE Key Fob with your thumb and pull the emergency key out with your other hand If one or more doors are open, or the liftgate is open, the while pushing the mechanical button.
Page 28 26 GETTING TO KNOW YOUR VEHICLE Transmitter Battery Replacement The recommended replacement battery is one CR2032 battery. NOTE: • Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate • Do not touch the battery terminals that are on the back housing or the printed circuit board.
Page 29 GETTING TO KNOW YOUR VEHICLE 27 new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 4. To assemble the RKE Key Fob case, snap the two halves together. Programming Additional Transmitters If you do not have a programmed RKE Key Fob, contact your authorized dealer for details.
Page 30 28 GETTING TO KNOW YOUR VEHICLE NOTE: When having the Sentry Key Immobilizer System CAUTION! serviced, bring all vehicle keys with you to an authorized • Always remove the Key Fobs from the vehicle and dealer. lock all doors when leaving the vehicle unat- KeySense Features —...
Page 31 GETTING TO KNOW YOUR VEHICLE 29 Start Up Display Features • Unique splash screen graphic • Telltale illuminated • After unique splash screen, and after stored messages are cycled, then start-up KeySense messages (Range & Max Speed) are displayed. The following features are always enabled when this key is in use: •...
Page 32: Ignition Switch
30 GETTING TO KNOW YOUR VEHICLE IGNITION SWITCH This feature allows the driver to operate the ignition switch with the push of a button, as long as the RKE Key Fob is in the passenger compartment, and the drivers foot on the brake pedal.
Page 33 GETTING TO KNOW YOUR VEHICLE 31 • The engine is stopped. • Some electrical devices are still available. ON/RUN • Driving position. • All the electrical devices are available. START • Start the engine. Keyless Push Button Ignition In case the ignition switch does not change with the push of a button, the RKE Key Fob may have a low or dead NOTE: The vehicle will not start if the RKE Key Fob is battery.
Page 34 32 GETTING TO KNOW YOUR VEHICLE WARNING! WARNING! (Continued) • Do not leave children or animals inside parked • When leaving the vehicle, always remove the Key vehicles in hot weather. Interior heat build-up may Fob from the vehicle and lock your vehicle. cause serious injury or death.
Page 35: Remote Starting System - If Equipped
GETTING TO KNOW YOUR VEHICLE 33 REMOTE STARTING SYSTEM — IF EQUIPPED Remote Start Cancel Message — If Equipped The following messages will display in the instrument This system uses the RKE Key Fob to start the cluster if the vehicle fails to remote start or exits remote engine conveniently from outside the vehicle start prematurely: while still maintaining security.
Page 36: How To Use Remote Start
34 GETTING TO KNOW YOUR VEHICLE • Ignition in STOP/OFF position How To Use Remote Start • Fuel level meets minimum requirement All of the following conditions must be met before the engine will remote start: WARNING! • Gear Selector in PARK •...
Page 37: To Enter Remote Start Mode
GETTING TO KNOW YOUR VEHICLE 35 To Enter Remote Start Mode To Exit Remote Start Mode Without Driving The Vehicle Push and release the REMOTE START button Push and release the REMOTE START button one time or on the RKE Key Fob twice within five seconds. allow the engine to run for the entire 15-minute cycle.
Page 38: Remote Start Comfort Systems - If Equipped
36 GETTING TO KNOW YOUR VEHICLE NOTE: For vehicles equipped with the Keyless Enter- Remote Start Windshield Wiper De–Icer N-Go — Passive Entry feature, the message “Remote Activation — If Equipped Start Active — Push Start Button” will display in the 3.5” When Remote Start is active and the outside ambient EVIC or 7”...
Page 39: Sentry Key
GETTING TO KNOW YOUR VEHICLE 37 2. This device must accept any interference received, used to start and operate the vehicle. The system will including interference that may cause undesired op- shut the engine off in two seconds if an invalid Key Fob eration.
Page 40: Vehicle Security Alarm - If Equipped
38 GETTING TO KNOW YOUR VEHICLE will pulse, the park lamps and/or turn signals will flash, CAUTION! and the Vehicle Security Light in the instrument cluster will flash. The Sentry Key Immobilizer system is not compat- ible with some aftermarket remote starting systems. Rearming Of The System Use of these systems may result in vehicle starting If something triggers the alarm, and no action is taken to...
Page 41: To Disarm The System
GETTING TO KNOW YOUR VEHICLE 39 • Grasp the Passive Entry Unlock Door Handle (if 2. Perform one of the following methods to lock the vehicle: equipped, refer to Keyless Enter-N-Go — Passive • Push LOCK on the interior power door lock switch Entry in Getting To Know Your Vehicle for further information).
Page 42: Doors
40 GETTING TO KNOW YOUR VEHICLE not disarm the Vehicle Security Alarm. If someone If the Vehicle Security Alarm is armed and the battery enters the vehicle through the liftgate and opens any becomes disconnected, the Vehicle Security Alarm will door, the alarm will sound.
Page 43 GETTING TO KNOW YOUR VEHICLE 41 Manual Front Door Lock location Manual Door Lock Rocker Switch 1 — Manual Door Lock 2 — Door Handle...
Page 44 42 GETTING TO KNOW YOUR VEHICLE If the door lock button is locked (no ribbing is visible) when you shut the door, the door will lock. Therefore, make sure the Key Fob is not inside the vehicle before closing the door. NOTE: The manual door locks will not lock or unlock the liftgate.
Page 45: Central Lock/Unlock - If Equipped
GETTING TO KNOW YOUR VEHICLE 43 • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
Page 46: Unlock Doors Automatically On Exit - If Equipped
44 GETTING TO KNOW YOUR VEHICLE you from accidentally locking your keys in the vehicle. For further information, refer to Uconnect Settings” in Placing the ignition in the OFF position or closing the “Multimedia”. door will allow the locks to operate. A chime will sound Keyless Enter-N-Go —...
Page 47 GETTING TO KNOW YOUR VEHICLE 45 • If the vehicle is unlocked by Passive Entry and no door is opened within 60 seconds, the vehicle will re-lock and if equipped will arm the security alarm. • If the child safety locks have been engaged the sliding side doors can be unlocked from the outside using the hands free RKE or Passive Entry system.
Page 48 46 GETTING TO KNOW YOUR VEHICLE To Unlock From The Passenger Side: FOBIK-Safe only executes in vehicles with Passive Entry. There are three situations that trigger a FOBIK-Safe With a valid RKE key fob within 3 ft (1 m) of the search in any Passive Entry vehicle: passenger door handle, grab the front passenger door •...
Page 49 GETTING TO KNOW YOUR VEHICLE 47 NOTE: The vehicle will only unlock the doors when a To Enter The Liftgate valid RKE key fob is detected inside the vehicle, and no With a valid RKE key fob within 3 ft (1 m) of the liftgate, valid RKE key fob is detected outside the vehicle.
Page 50 48 GETTING TO KNOW YOUR VEHICLE To Lock The Vehicle’s Doors Do NOT grab the door handle, when pushing the door handle button. This could unlock the door(s). With one of the vehicle’s RKE key fobs within 3 ft (1 m) of the driver or passenger front door handle, push the door handle LOCK button to lock all four doors and the liftgate.
Page 51: Manual Sliding Side Door
GETTING TO KNOW YOUR VEHICLE 49 NOTE: rocking forward and back. Rocking the handle back- wards opens the door and rocking forward releases the • After pushing the door handle button, you must wait hold open latch in order to close the door. two seconds before you can lock or unlock the doors, To keep your door operating properly, observe the fol- using either Passive Entry door handle.
Page 52: Power Sliding Side Door - If Equipped
50 GETTING TO KNOW YOUR VEHICLE Always make sure that the sliding door is fully latched Power Sliding Side Door — If Equipped anytime the vehicle is in motion. NOTE: The left side sliding door cannot be opened while the fuel door is open. Side Door Handle And Lock Functions 1 —...
Page 53 GETTING TO KNOW YOUR VEHICLE 51 The power sliding door may be power opened or closed The RKE Key Fob and the overhead console button will in several ways: operate the door when the door is locked. All other ways require the sliding door to be unlocked.
Page 54 52 GETTING TO KNOW YOUR VEHICLE the LED is lit, pushing the power sliding door power OFF button will return the handles to power operation. NOTE: Tones are sounded and the turn signals are flashed with sliding door movements. These alerts can be turned on or off in ‘Uconnect Settings’.
Page 55 GETTING TO KNOW YOUR VEHICLE 53 power Off button, located in the overhead console, to remove power to the handles and buttons just inside the sliding doors. NOTE: • The sliding door will not power open or close if the gear selector is not in Park or Neutral.
Page 56: Hands-Free Sliding Doors - If Equipped
54 GETTING TO KNOW YOUR VEHICLE Hands-Free Sliding Doors – If Equipped WARNING! Hands-Free Feature Personal injury or cargo damage may occur if caught in the path of the sliding door. Make sure the door path is clear before closing the door. WARNING! Before driving off, check the instrument cluster for a sliding door or door open message or warning indi-...
Page 57: Safe Lock Device - If Equipped
GETTING TO KNOW YOUR VEHICLE 55 • If anything obstructs the power sliding doors while it vehicle in the general location below the door handle(s). Do not move your foot sideways or in a sweeping motion is closing or opening, the sliding doors will automati- or the sensors may not detect the motion.
Page 58: Child Locks
56 GETTING TO KNOW YOUR VEHICLE Child Locks To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a Child Protection Door Lock system. NOTE: When the Child Safety Locks have been engaged the sliding side doors can be unlocked from the outside using the hands free RKE or Passive Entry system.
Page 59 GETTING TO KNOW YOUR VEHICLE 57 NOTE: • After engaging (or disengaging) the Child Protection Door Lock, always test the inside door handle with the sliding door closed to make certain the Child Protec- tion Door Lock is in the desired position. The inside door handle will not open the sliding door when the Child Protection Door Lock is engaged.
Page 60: Seats
58 GETTING TO KNOW YOUR VEHICLE LED is lit, the sliding door may not be power opened 3. Repeat Steps 1 and 2 on the opposite sliding door. or closed by pushing the buttons just inside the sliding NOTE: doors or pulling on the handles. •...
Page 61: Manual Adjustment (Front Seats)
GETTING TO KNOW YOUR VEHICLE 59 WARNING! (Continued) WARNING! (Continued) these areas are more likely to be seriously injured adjusted properly and you could be injured. Adjust or killed. the seat only while the vehicle is parked. • Do not allow people to ride in any area of your •...
Page 62 60 GETTING TO KNOW YOUR VEHICLE WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked.
Page 63 GETTING TO KNOW YOUR VEHICLE 61 To recline, lean forward slightly, lift the lever, then push back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position. Using body pressure, lean forward and rearward on the seat to be sure the seatback has latched.
Page 64 62 GETTING TO KNOW YOUR VEHICLE Seat Height Adjustment The driver’s seat height can be raised or lowered by using a lever, located on the outboard side of the seat. Pump the lever upward to raise the seat height, or pump the lever downward to lower the seat height.
Page 65: Manual Adjustment (Rear Seats)
GETTING TO KNOW YOUR VEHICLE 63 Manual Adjustment (Rear Seats) normal position. Using body pressure, lean forward and rearward on the seat to be sure the seatback has latched. WARNING! • Adjusting a seat while the vehicle is moving is dangerous.
Page 66 64 GETTING TO KNOW YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Fold-Flat To fold the seat, lift the recliner lever to the full upward position and push the seatback forward until it rests on...
Page 67 GETTING TO KNOW YOUR VEHICLE 65 • When returning the seat to the original position, the Easy Entry headrest must be folded back to the original position. Easy Tilt Seat — With Or Without Child Seat Installed The 2nd row seats can be tilted forward for easy entry into the third row with or without a child seat installed.
Page 68 66 GETTING TO KNOW YOUR VEHICLE Easy Tilt Seat Lever Seat Folded Forward With Child Seat Installed 2. To put the seat back into original position, just pull back on the seatback and lock the seat into position.
Page 69 GETTING TO KNOW YOUR VEHICLE 67 WARNING! Do not use this feature with a child in seat. Serious injury or death my occur. Easy Entry — With The Seat Folded Flat The seats can be folded and tilted for more accessibility for passengers to enter and exit the third row.
Page 70 68 GETTING TO KNOW YOUR VEHICLE Exit For 3rd Row Passengers For passengers seated in the third row, there is a pull strap located on the outboard side of the seat near the bottom of the seat back. Third row passengers can pull on the strap and push the seat forward for folding the seatback down and tilting the seat to the floor.
Page 71 GETTING TO KNOW YOUR VEHICLE 69 NOTE: This process is for when there is no child seat The Stow ‘n Go Assist feature is available to both the installed. Use the easy entry lever if a child seat is front driver and passenger power seats. installed.
Page 72 70 GETTING TO KNOW YOUR VEHICLE Using the Stow ‘n Go Assist Feature NOTE: • The button is only functional when the power sliding door is open and the vehicle is in PARK. If the door is not open or the vehicle is not in PARK when the button is pushed, the front seat will not move and a message will be displayed in Electronic Vehicle Information Center (EVIC) or Drivers Information Display (DID).
Page 73 GETTING TO KNOW YOUR VEHICLE 71 2. Perform the second row Stow ‘n Go seat movement. location. A message will be displayed in the instru- Refer to “Second Row Stow ‘n Go” for further infor- ment cluster indicating that an obstacle has been mation.
Page 74 72 GETTING TO KNOW YOUR VEHICLE using the recliner handle located on the outboard side of the cushion. Move the seat height to at least mid position using the height adjuster handle in the outboard side of the cushion. For Power Seats: Push the Stow ‘n Go Assist button located on the B pillar trim (if equipped.) Refer to Stow ’n Go Assist - If Equipped in this section for instructions.
Page 75 GETTING TO KNOW YOUR VEHICLE 73 • For information on storage bin function with the 3. Pull the floor panel and position it toward the front seats rearward refer to “Second Row Floor Storage seats while folding the top half down and rest it Bins”...
Page 76 74 GETTING TO KNOW YOUR VEHICLE 4. Stow the seat by grabbing the strap on the lower part 5. Push down on the seat back to lock the seat in the tub. of the back seat and guide the seat into the tub. Push To Lock Pull Strap...
Page 77 GETTING TO KNOW YOUR VEHICLE 75 6. Close the floor by pulling the floor panel backwards by the bottom corner edge of the panel. Push To Lock 8. Readjust the front seat as needed. Extend Floor Panel 7. Push down on floor panel to lock into place.
Page 78 76 GETTING TO KNOW YOUR VEHICLE To Unstow Second Row Seats CAUTION! For Manual Seats: To unstow the seat from the floor, • The storage bin cover must be locked and flat to move the front seat all the way forward using the manual avoid damage from contact with the front seat seat adjustment bar.
Page 79 GETTING TO KNOW YOUR VEHICLE 77 2. Pull the latch located near the second row seat to open the floor panel. Lock Rod NOTE: Floor Latch • Push the lock rod inward for the locked position. 3. Pull the floor panel and position it toward the front •...
Page 80 78 GETTING TO KNOW YOUR VEHICLE NOTE: The seatback may be locked, if it is, it will be necessary to use the recliner handle to unlock the back before folding into the upright position. Push Panel Forward 4. Pull the strap located on the seat and pull the seat out of the storage bin.
Page 81 GETTING TO KNOW YOUR VEHICLE 79 Extend Panel Push Down To lock 6. Lay the floor panel flat and push down until it clicks 7. Readjust the front seat as needed. into position. Replace the floor mat as needed.
Page 82 80 GETTING TO KNOW YOUR VEHICLE WARNING! • In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are fully latched. • Sitting in a seat with the head restraint in its lowered position could result in serious injury or death in a collision.
Page 83 GETTING TO KNOW YOUR VEHICLE 81 Release Strap In Floor Detent Guides NOTE: Seat can be removed easier with one outboard WARNING! seat stowed in the load floor. If not properly latched, the seat could become loose. To reinstall the seat, align the seat into the detent posi- Personal injuries could result.
Page 84 82 GETTING TO KNOW YOUR VEHICLE Manually Folding Third Row Seats — If Equipped 3. Pull release strap marked “2” and tumble the seat rearward into the storage bin. 1. Lower the center head restraint down to the seatback by pushing the button on the guide and pushing the head restraint down.
Page 85 GETTING TO KNOW YOUR VEHICLE 83 2. Pulling strap “2” releases the seatback to return to its full upright position. Stowed Third Row Seat To Unfold Third Row Seats Strap “2” 1. Pull up on the assist strap to lift the seat out of the 3.
Page 86: Power Adjustment (Front Seats) - If Equipped
84 GETTING TO KNOW YOUR VEHICLE WARNING! • In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are fully latched. • Sitting in a seat with the head restraint in its lowered position could result in serious injury or death in a collision.
Page 87 GETTING TO KNOW YOUR VEHICLE 85 WARNING! CAUTION! • Adjusting a seat while driving may be dangerous. Do not place any article under a power seat or Moving a seat while driving could result in loss of impede its ability to move as it may cause damage to control which could cause a collision and serious the seat controls.
Page 88 86 GETTING TO KNOW YOUR VEHICLE Tilting The Seat Up Or Down CAUTION! (Continued) The angle of the seat cushion can be adjusted in four movement is stopped by an obstruction in the seat’s directions. Pull upward or push downward on the front path.
Page 89: Power Adjustment (Rear Seats) - If Equipped
GETTING TO KNOW YOUR VEHICLE 87 Power Lumbar — If Equipped WARNING! (Continued) Vehicles equipped with power driver or passenger seats injury or death could result from a poorly adjusted may be equipped with power lumbar. The power lumbar seat belt. switch is located on the outboard side of the power seat.
Page 90 88 GETTING TO KNOW YOUR VEHICLE Third Row Power Recline — If Equipped The power recline feature, located on the trim panel next to the seat, adjusts the seatback angle forward/rearward for occupant comfort. Reclining The Seatback The angle of the seatback can be adjusted forward or rearward.
Page 91 GETTING TO KNOW YOUR VEHICLE 89 NOTE: • The outer head restraints will lower automatically as necessary when the power seat begins to move. • The center head restraint raises and lowers manually but will not lower automatically. • The head restraint can also be lowered manually using the pull strap located at the back off the seat.
Page 92: Driver Memory Seat - If Equipped
90 GETTING TO KNOW YOUR VEHICLE • To abort seat operation while seat is in motion, push a To move the selected seat(s) to the Normal (seated) position, push and release the Normal button. The seat different seat position selector switch to stop the seat. will automatically stop when the Normal position is Once the seat stops moving, then the desired position reached.
Page 93 GETTING TO KNOW YOUR VEHICLE 91 Your vehicle may have been delivered with two RKE key fobs, one RKE key fob can be linked to each of the memory positions. Programming The Memory Feature To create a new memory profile, perform the following: 1.
Page 94 92 GETTING TO KNOW YOUR VEHICLE Information Center (EVIC) or Driver Information Dis- NOTE: Before programming your RKE Key Fob you play (DID) will display which memory position has must select the “Personal Settings Linked to Key Fob” been set. feature through the Uconnect Settings.
Page 95 GETTING TO KNOW YOUR VEHICLE 93 5. Push and release the LOCK button on the RKE Key A recall can be cancelled by pushing any of the MEMORY Fob within 10 seconds. buttons on the driver’s door during a recall (S, 1, or 2). When a recall is cancelled, the driver’s seat stop moving.
Page 96: Heated Seats - If Equipped
94 GETTING TO KNOW YOUR VEHICLE (60 mm) rearward if the driver seat position is greater Each stored memory setting will have an associated Easy than or equal to 2.7 inches (67.7 mm) forward of the Entry and Easy Exit Position. rear stop.
Page 97 GETTING TO KNOW YOUR VEHICLE 95 • Press the heated seat button • The engine must be running for the heated seats to once to turn the HI setting ON. operate. • Press the heated seat button a second time to turn Vehicles Equipped With Remote Start the LO setting ON.
Page 98 96 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) even at low temperatures, especially if used for long periods of time • Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat.
Page 99: Ventilated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE 97 Push the switch once to select HI-level heating. Push the air through fine perforations in the seat cover to help switch a second time to select LO-level heating. Push the keep the driver and front passenger cooler in higher switch a third time to shut the heating elements OFF.
Page 100: Plastic Grocery Bag Retainer Hooks
98 GETTING TO KNOW YOUR VEHICLE Vehicles Equipped With Remote Start HEAD RESTRAINTS On models that are equipped with remote start, the Head restraints are designed to reduce the risk of injury ventilated seats can be programed to come on during a by restricting head movement in the event of a rear remote start.
Page 101: Head Restraints - Front Seats
GETTING TO KNOW YOUR VEHICLE 99 Head Restraints — Front Seats The front driver and passenger seats are equipped with four-way head restraints. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, push the adjust- ment button, located at the base of the head restraint, and push downward on the head restraint.
Page 102: Head Restraints - Second Row
100 GETTING TO KNOW YOUR VEHICLE Head Restraints — Third Row WARNING! The outboard head restraints can be manually folded • A loose head restraint thrown forward in a colli- forward for improved visibility while in reverse. Pull the sion or hard stop could cause serious injury or release strap to fold them forward.
Page 103: Power Folding Third Row Head Restraints - If Equipped
GETTING TO KNOW YOUR VEHICLE 101 NOTE: Press the Head Restraint Fold button to power fold the third row head restraints. • The head restraints must be raised manually when occupying the third row. NOTE: • Do not fold if there are passengers seated in the third •...
Page 104: Heated Steering Wheel - If Equipped
102 GETTING TO KNOW YOUR VEHICLE steering column in position, push the lever upward until fully engaged. WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle.
Page 105 GETTING TO KNOW YOUR VEHICLE 103 The heated steering wheel control button is located WARNING! within the Uconnect controls screen. • Persons who are unable to feel pain to the skin • Press the heated steering wheel button once to because of advanced age, chronic illness, diabetes, turn the heating element ON.
Page 106: Mirrors
104 GETTING TO KNOW YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped A single ball joint mirror is used to allow the driver to adjust up, down and left, right. Mirror should be ad- justed to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
Page 107: Automatic Dimming Mirror - If Equipped
GETTING TO KNOW YOUR VEHICLE 105 Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pushing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated.
Page 108: Outside Mirrors
106 GETTING TO KNOW YOUR VEHICLE Outside Mirrors by the inside automatic dimming mirror and will auto- matically adjust for headlight glare when the inside To receive maximum benefit, adjust the outside mirror(s) mirror adjusts. to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.
Page 109: Heated Mirrors - If Equipped
GETTING TO KNOW YOUR VEHICLE 107 Using the mirror control switch, push on any of the four arrows for the direction that you want the mirror to move. Left and Right side power mirror preselected positions can be controlled by the optional Driver Memory Seat Feature.
Page 110: Power Folding Mirrors - If Equipped
108 GETTING TO KNOW YOUR VEHICLE ground rearward of the front doors. The driver’s outside Push the switch once and the mirrors will fold in, mirror will move slightly downward from the present pushing the switch a second time will return the mirrors position when the vehicle is shifted into REVERSE.
Page 111: Illuminated Vanity Mirrors - If Equipped
GETTING TO KNOW YOUR VEHICLE 109 If the mirrors are in the folded position, and vehicle Illuminated Vanity Mirrors — If Equipped speed is equal or greater than 10 mph (16 km/h), they An illuminated vanity mirror is located on the sun visor. will automatically unfold.
Page 112: Conversation Mirror
110 GETTING TO KNOW YOUR VEHICLE Conversation Mirror EXTERIOR LIGHTS Located in the overhead console there is a conversation Headlight Switch mirror to view all the passengers in the vehicle. Push the The headlight switch is located on the left side of the panel to release the drop down mirror.
Page 113: Automatic Headlights - If Equipped
GETTING TO KNOW YOUR VEHICLE 111 Rotate the headlight switch clockwise to the second detent for parking light and instrument panel light operation. Rotate the headlight switch to the third detent for headlight, parking light and instrument panel opera- tion. Automatic Headlights —...
Page 114: Headlights On With Wipers - If Equipped
112 GETTING TO KNOW YOUR VEHICLE Headlights On With Wipers — If Equipped headlights or parking lights are turned back on or the ignition switch is turned ON, the delay will be cancelled. When your headlights are in the AUTO mode and the engine is running, the headlights will automatically turn When exiting the vehicle the driver can choose to have on when the wiper system is also turned on.
Page 115: Daytime Running Lights - If Equipped
GETTING TO KNOW YOUR VEHICLE 113 Daytime Running Lights — If Equipped The headlights or LED light bars on your vehicle will illuminate when the engine is started. This provides a constant lights on condition until the ignition is turned OFF.
Page 116: Turn Signals
114 GETTING TO KNOW YOUR VEHICLE Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. NOTE: If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb.
Page 117: Lane Change Assist - If Equipped
GETTING TO KNOW YOUR VEHICLE 115 Lane Change Assist — If Equipped Automatic High Beam — If Equipped Tap the lever up or down once, without moving beyond The Automatic High Beam system provides increased the detent, and the turn signal (right or left) will flash forward lighting at night by automating high beam three times then automatically turn off.
Page 118: Battery Protection
116 GETTING TO KNOW YOUR VEHICLE 2. Rotate the headlight switch counterclockwise to the 2. Pull the multifunction lever toward you to switch the AUTO (A) position. headlights from the high beam to the low beam position. 3. Push the multifunction lever away from you to switch the headlights to the high beam position.
Page 119: Interior Lights
GETTING TO KNOW YOUR VEHICLE 117 INTERIOR LIGHTS To operate the courtesy lights, push either the driver’s or passenger light switch. Courtesy/Interior Lighting NOTE: The courtesy light switches are used to turn the courtesy • Before exiting the vehicle, make sure that the interior lights On/Off.
Page 120: Instrument Panel Dimmer Control
118 GETTING TO KNOW YOUR VEHICLE The courtesy lights also function as reading lights. Push Instrument Panel Dimmer Control the lens to turn these lights ON while inside the vehicle. The instrument panel dimmer control is part of the Push the lens a second time to turn each light OFF. headlight switch and is located on the driver’s side of the instrument panel.
Page 121 GETTING TO KNOW YOUR VEHICLE 119 Ambient Light Control — If Equipped Rotate the ambient dimmer control upward or down- ward to increase or decrease the brightness of the ambi- ent light located in the overhead console, door handle lights, under I/P lights, door map pocket lights, and cubby bin lights.
Page 122: Windshield Wiper And Washers
120 GETTING TO KNOW YOUR VEHICLE Interior Lighting Off Rotate the right (instrument panel) dimmer control to the off position (extreme bottom). The interior lights will remain off when the doors or liftgate are open. Parade Mode (Daytime Brightness Feature) Rotate the instrument panel dimmer control upward to the first detent.
Page 123: Intermittent Wiper System
GETTING TO KNOW YOUR VEHICLE 121 The delay intervals will double in duration when the WARNING! vehicle speed is 10 mph (16 km/h) or less. Sudden loss of visibility through the windshield Windshield Wiper Operation could lead to a collision. You might not see other Rotate the end of the lever upward, to the first detent past vehicles or other obstacles.
Page 124: Mist Feature
122 GETTING TO KNOW YOUR VEHICLE Mist Feature With the windshield wipers on and reverse gear engaged, rear window wiping will be continuous in the same way. Use the Mist feature when weather conditions make occasional usage of the wipers necessary. Push the lever Rear Windshield Washer Operation upward to the Mist position and release for a single Pushing the windshield wiper lever forward activates the...
Page 125 GETTING TO KNOW YOUR VEHICLE 123 • Use of Rain-X or products containing wax or silicone the end of the multifunction lever to one of the four intermittent wiper sensitivity settings to activate this may reduce rain sensor performance. feature. •...
Page 126: Climate Controls
124 GETTING TO KNOW YOUR VEHICLE • Neutral Wipe Inhibit — The Rain Sensing feature will CLIMATE CONTROLS not operate when the ignition is ON, and the transmis- Manual Climate Controls – 3 Zone — If Equipped sion gear selector is in the NEUTRAL position, and the vehicle speed is less than 3 mph (5 km/h), unless the wiper control on the multifunction lever is moved, the vehicle speed is greater than 3 mph (5 km/h), or the...
Page 127 GETTING TO KNOW YOUR VEHICLE 125 1. MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is ON. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.
Page 128 126 GETTING TO KNOW YOUR VEHICLE NOTE: window demist outlets. When the defrost button is selected, the blower level will increase. Use Defrost mode • Continuous use of the Recirculation mode may make with maximum temperature settings for best windshield the inside air stuffy and window fogging may occur.
Page 129 GETTING TO KNOW YOUR VEHICLE 127 slide the temperature bar towards the red arrow button CAUTION! on the touchscreen for warmer temperature settings. When the SYNC feature is active, the passenger’s tem- Failure to follow these cautions can cause damage to perature will move up with the driver’s temperature, the heating elements: •...
Page 130 128 GETTING TO KNOW YOUR VEHICLE • Panel automatic mode to switch to manual operation. The speeds can be selected using either the blower control Air comes from the outlets in the instrument knob on the faceplate or the buttons on the touchscreen panel.
Page 131 GETTING TO KNOW YOUR VEHICLE 129 • Floor 11. Driver Temperature Control Down Button Air is directed through the floor outlets with a Provides the driver with independent temperature con- small amount flowing through the defrost and trol. Push the button on the faceplate for cooler tempera- side window demister outlets.
Page 132 130 GETTING TO KNOW YOUR VEHICLE Rear Manual Temperature Control The rear MTC system has floor air outlets at the rear right side of the 3rd Row seats and overhead outlets at each outboard rear seating position. The system provides heated air through the floor outlets or cool, dehumidified air through the headliner outlets.
Page 133 GETTING TO KNOW YOUR VEHICLE 131 Rear Mode Control Rear Temperature Control Headliner Mode To change the temperature in the rear of the vehicle, push Air comes from the outlets in the headliner. temperature control up button to raise and down to Each of these outlets can be individually ad- lower and clockwise to increase the temperature.
Page 134: Automatic Temperature Control (Atc) - 3 Zone - If Equipped
132 GETTING TO KNOW YOUR VEHICLE CAUTION! Interior air enters the Rear Automatic Temperature Control System through an intake grille, located in floor under the passengers’ seats. Do not block or place objects directly in front of the inlet grille or heater outlets.
Page 135 GETTING TO KNOW YOUR VEHICLE 133 Buttons On The Touchscreen Buttons on the touchscreen are accessible on the Uconnect system screen. Uconnect 8.4 Automatic Climate Controls — Buttons On The Touchscreen Automatic Temperature Controls — Buttons On The Faceplate...
Page 136 134 GETTING TO KNOW YOUR VEHICLE Button Descriptions (Applies To Both Buttons On The 3. Recirculation Button Faceplate And Buttons On The Touchscreen) Press and release this button to change the system 1. MAX A/C Button between recirculation mode and outside air mode. Recir- culation can be used when outside conditions such as Press and release to change the current setting, the smoke, odors, dust, or high humidity are present.
Page 137 GETTING TO KNOW YOUR VEHICLE 135 with maximum temperature settings for best windshield CAUTION! and side window defrosting and defogging. Performing this function will cause the Automatic Temperature Con- Failure to follow these cautions can cause damage to trol (ATC) to switch into manual mode. If the front the heating elements: •...
Page 138 136 GETTING TO KNOW YOUR VEHICLE 8. Passenger Temperature Control Up Button 10. SYNC Provides the passenger with independent temperature Press the Sync button on the touchscreen to toggle the control. Push the button on the faceplate for warmer Sync feature On/Off. The Sync indicator is illuminated temperature settings or on the touchscreen, press and when this feature is enabled.
Page 139 GETTING TO KNOW YOUR VEHICLE 137 11. Blower Control 12. Modes Blower control is used to regulate the amount of air Push the button in the center of the knob to change the forced through the climate system. There are seven airflow distribution mode.
Page 140 138 GETTING TO KNOW YOUR VEHICLE • Bi-Level Mode require extra heat to the windshield. This setting is good for maintaining comfort while reducing mois- Air comes from the instrument panel outlets ture on the windshield. and floor outlets. A slight amount of air is directed through the defrost and side window demis- 13.
Page 141 GETTING TO KNOW YOUR VEHICLE 139 15. Driver Temperature Control Up Button Climate Control Functions Provides the driver with independent temperature con- A/C (Air Conditioning) trol. Push the button on the faceplate for warmer tem- The Air Conditioning (A/C) button allows the operator perature settings or on the touchscreen, press and slide to manually activate or deactivate the air conditioning the temperature bar button towards the red arrow for...
Page 142 140 GETTING TO KNOW YOUR VEHICLE dirt or insects. Clean with a gentle water spray from recirculate interior air by pressing the Recirculation con- the front of the radiator and through the condenser. trol button. The recirculation indicator will illuminate when this button is selected.
Page 143 GETTING TO KNOW YOUR VEHICLE 141 Automatic Temperature Control (ATC) NOTE: • It is not necessary to move the temperature settings. Automatic Operation The system automatically adjusts the temperature, 1. Push the AUTO button on the front ATC Panel and the mode and fan speed to provide comfort as quickly as word “AUTO”...
Page 144 142 GETTING TO KNOW YOUR VEHICLE • To return to the Front screen on the Uconnect 8.4 radio, NOTE: The system will not automatically sense the presence of fog, mist or ice on the windshield. DEFROST press the Front Climate button on the touchscreen. To mode must be manually selected to clear the windshield return to the Front screen on the Uconnect 5.0 radio, and side glass.
Page 145 GETTING TO KNOW YOUR VEHICLE 143 3. Blower Control Display This display shows the current Blower speed selection. 4. Rear Auto Indicator This indicates when the system is in Rear Auto mode. Rear Automatic Temperature Control (ATC) — If Equipped The rear ATC system has floor air outlets underneath the passengers’...
Page 146 144 GETTING TO KNOW YOUR VEHICLE 1. Adjust the Rear Blower, Rear Temperature and the Rear Modes to suit your comfort needs. 2. ATC is selected by pushing the AUTO button. Once the desired temperature is displayed, the ATC System will automatically achieve and maintain that comfort level.
Page 147 GETTING TO KNOW YOUR VEHICLE 145 Rear Blower Control When rear controls are locked by the front system, the Rear Temperature Lock symbol on the ATC panel is The rear blower control head can be manually set to off, illuminated and any rear overhead adjustments are ig- or any fixed blower speed, by pushing the blower control nored.
Page 148: Operating Tips
146 GETTING TO KNOW YOUR VEHICLE Headliner Mode Operating Tips Air comes from the outlets in the headliner. Each NOTE: Refer to the chart at the end of this section for of these outlets can be individually adjusted to suggested control settings for various weather condi- direct the flow of air.
Page 149 GETTING TO KNOW YOUR VEHICLE 147 Lubricants” in “Technical Data” for proper coolant selec- Outside Air Intake tion. Use of the air Recirculation mode during Winter Make sure the air intake, located directly in front of the months is not recommended, because it may cause windshield, is free of obstructions such as leaves.
Page 150 148 GETTING TO KNOW YOUR VEHICLE Operating Tips Chart...
Page 151: Windows
GETTING TO KNOW YOUR VEHICLE 149 WINDOWS Power Windows Driver Power Window Controls You can control either the front or rear windows using controls located on the driver’s door trim panel. The driver may lock out the rear power windows by pushing the bar control just below the power window controls.
Page 152 150 GETTING TO KNOW YOUR VEHICLE NOTE: Power Window controls will also remain active Front Passenger Power Door Controls for up to 10 minutes after the ignition switch has been turned to OFF, depending upon the accessory delay setting. Opening a front door will cancel this feature. There is a single control on the front passenger’s door trim panel which operates the passenger door window and a set of controls that lock and unlock all doors.
Page 153 GETTING TO KNOW YOUR VEHICLE 151 • Any impact due to rough road conditions may trigger Auto Up Feature With Anti-Pinch Protection — If Equipped the auto reverse function unexpectedly during auto- closure. If this happens, pull the control lightly to the The front driver and front passenger controls may be first detent and hold to close window manually.
Page 154 152 GETTING TO KNOW YOUR VEHICLE 2. Push the window control down firmly to the second detent to open the window completely and continue to hold the control down for an additional two sec- onds after the window is fully open. Sliding Side Door Power Window Control —...
Page 155: Tri-Pane Vista View Sunroof - If Equipped
GETTING TO KNOW YOUR VEHICLE 153 windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the rear windows are open and buffeting occurs, open the front and rear windows together to minimize the buffeting.
Page 156: Opening Sunroof
154 GETTING TO KNOW YOUR VEHICLE WARNING! WARNING! (Continued) • Do not allow small children to operate the sunroof. • Never leave children unattended in a vehicle, or Never allow your fingers, other body parts, or any with access to an unlocked vehicle. Never leave the object, to project through the sunroof opening.
Page 157: Closing Sunroof
GETTING TO KNOW YOUR VEHICLE 155 Manual Mode Closing Sunroof To open the sunroof, push and hold the switch rearward Express Mode to full open. Any release of the switch will stop the Push the switch forward and release it within one second movement.
Page 158: Power Sun Shade - If Equipped
156 GETTING TO KNOW YOUR VEHICLE windows down, or the sunroof (if equipped) in certain Opening Power Shade — Manual Mode open or partially open positions. This is a normal occur- To open the shade, push and hold the switch rearward. rence and can be minimized.
Page 159: Pinch Protect Feature
GETTING TO KNOW YOUR VEHICLE 157 NOTE: If the sunroof is open, the shade will close to the NOTE: If three consecutive sunroof close attempts result half-open position. Pushing the shade close button again in Pinch Protect reversals, Pinch Protect will disable and will automatically close both the sunroof and shade the sunroof must be closed in Manual Mode.
Page 160: Hood
158 GETTING TO KNOW YOUR VEHICLE HOOD Opening The hood release lever (to open the primary latch) and safety latch (to open the secondary latch) must be re- leased to open the hood. 1. Pull the hood release lever located under the driver’s side of the instrument panel.
Page 161: Closing
GETTING TO KNOW YOUR VEHICLE 159 NOTE: • Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position. • While lifting the hood, use both hands. • Vehicle must be at a stop and the automatic transmis- sion must be in park.
Page 162: Liftgate
160 GETTING TO KNOW YOUR VEHICLE LIFTGATE CAUTION! Opening To prevent possible damage, do not slam the hood to To Unlock/Enter The Liftgate close it. Lower hood to approximately 12 in (30 cm) and drop the hood to close. Make sure hood is fully The liftgate may be released in several ways: closed for both latches.
Page 163 GETTING TO KNOW YOUR VEHICLE 161 vehicle is equipped with Passive Entry, pulling the out- side handle will unlock and release the liftgate, with a valid Passive Entry RKE Key Fob within 3 ft (1 m) of the liftgate. Unlock Liftgate Using An RKE Key Fob The RKE Key Fob and the overhead console button will release the liftgate when the liftgate is locked.
Page 164: Closing
162 GETTING TO KNOW YOUR VEHICLE NOTE: If “Unlock All Doors 1st Press”’ is programmed in Uconnect Settings, all doors will unlock with a Passive Entry handle activation. If ‘Unlock Driver Door 1st Press” is programmed in Uconnect Settings, only the liftgate will unlock.
Page 165: Power Liftgate - If Equipped
GETTING TO KNOW YOUR VEHICLE 163 • RKE Key Fob WARNING! • Outside handle (opens liftgate only) • Driving with the liftgate open can allow poisonous • Button just inside the liftgate on the upper left trim exhaust gases into your vehicle. You and your (when liftgate is open) passengers could be injured by these fumes.
Page 166 164 GETTING TO KNOW YOUR VEHICLE outside handle requires the liftgate to be unlocked. If the vehicle is equipped with Passive Entry, pulling the out- side handle or Hands-Free Liftgate foot activation (if equipped) will unlock and open the liftgate, with a valid Passive Entry RKE Key Fob within 3 ft (1 m) of the liftgate handle.
Page 167: Hands-Free Liftgate - If Equipped
GETTING TO KNOW YOUR VEHICLE 165 NOTE: Tones are sounded and the turn signals are Hands-Free Liftgate — If Equipped flashed with liftgate movements. These alerts can be turned on or off in Uconnect Settings. Refer to “Uconnect Settings” in “Multimedia” for further information. Lock The Vehicle With a valid Passive Entry RKE Key Fob within 3 ft (1 m) of the liftgate, pushing the passive entry lock button...
Page 168 166 GETTING TO KNOW YOUR VEHICLE below the liftgate door handle. Do not move your foot The Hands-Free Liftgate feature may be turned on or sideways or in a sweeping motion or the sensors may not off in Uconnect Settings. Refer to “Uconnect Settings” detect the motion.
Page 169 GETTING TO KNOW YOUR VEHICLE 167 • If the power liftgate encounters multiple obstructions WARNING! (Continued) within the same cycle, the system will automatically the liftgate closed when you are operating the stop. If this occurs, the liftgate must be opened or vehicle.
Page 170: Cargo Area Features
168 GETTING TO KNOW YOUR VEHICLE WARNING! During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away. Cargo Area Features Cargo Area Storage When the third row seats are not in the stowed position, there is a large area for cargo storage.
Page 171 GETTING TO KNOW YOUR VEHICLE 169 Stow n’ VAC Integrated Vacuum — If Equipped WARNING! Your vehicle may be equipped with an integrated Carbon monoxide (CO) in exhaust gases is deadly. vacuum system. The system can clean up dry spills and Follow the precautions below to prevent carbon debris within the vehicle.
Page 172 170 GETTING TO KNOW YOUR VEHICLE 2. Open front vacuum storage compartments to access the attachments if needed. Power Buttons 1 — Low Power Indicator Light Front Storage Compartments 2 — On/Off Button 1 — Retractable Vacuum Head/Hose Location 3. Pull out the vacuum hose and push the power button 2 —...
Page 173 GETTING TO KNOW YOUR VEHICLE 171 Vacuum Attachments • Crevice Tool — Able to reach into tight spots including the latches located in the floor for the seats. • Upholstery Tool — Use to agitate dirt and debris from carpets and seats. This tool can also be used to pick up pet hair as well.
Page 174 172 GETTING TO KNOW YOUR VEHICLE To Remove And Empty The Debris Bin To access and remove the debris bin, open the lower access panel by pulling outward on the finger grip area of the door. For debris bin removal, twist the (color) release knob counterclockwise and pull the bin towards you.
Page 175 GETTING TO KNOW YOUR VEHICLE 173 • If the filter is clogged, follow the emptying debris bin Flammable / Explosive Liquids And Vapors procedure and lightly tap the filter on the collection Do not vacuum any flammable liquid bin to remove any collected debris from the filter spills or around explosive vapors.
Page 176 174 GETTING TO KNOW YOUR VEHICLE Carbon Monoxide Gas WARNING! Do not leave the vehicle’s liftgate open Flammable liquids and vapors can be ignited by if the vehicle is running while the heat, sparks, or flames. Vapors from flammable liq- vacuum is in use.
Page 177: Garage Door Opener - If Equipped
GETTING TO KNOW YOUR VEHICLE 175 GARAGE DOOR OPENER — IF EQUIPPED WARNING! (Continued) HomeLink replaces up to three hand-held transmitters vehicle is stopped in an open area with the engine that operate devices such as garage door openers, motor- running for more than a short period, adjust the ized gates, lighting or home security systems.
Page 178: Before You Begin Programming Homelink
176 GETTING TO KNOW YOUR VEHICLE For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink system.
Page 179 GETTING TO KNOW YOUR VEHICLE 177 Programming A Rolling Code For programming garage door openers that were manu- factured after 1995. These garage door openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the garage door opener.
Page 180 178 GETTING TO KNOW YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) there may be a light that blinks when the garage door away from the HomeLink button you wish to program opener/device is in the LEARN/TRAIN mode. while keeping the HomeLink indicator light in view.
Page 181 GETTING TO KNOW YOUR VEHICLE 179 Reprogramming A Single HomeLink Button (Rolling 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 Code) cm) away from the HomeLink button you wish to program while keeping the HomeLink indicator light To reprogram a channel that has been previously trained, in view.
Page 182: Canadian/Gate Operator Programming
180 GETTING TO KNOW YOUR VEHICLE • To program the two remaining HomeLink buttons, Canadian/Gate Operator Programming repeat each step for each remaining button. DO NOT For programming transmitters in Canada/United States erase the channels. that require the transmitter signals to “time-out” after several seconds of transmission.
Page 183 GETTING TO KNOW YOUR VEHICLE 181 2. Place the hand-held transmitter 1 to 3 inches NOTE: (3 to 8 cm) away from the HomeLink button you wish • If the indicator light stays on constantly, program- to program while keeping the HomeLink indicator ming is complete and the garage door/device should light in view.
Page 184: Using Homelink
182 GETTING TO KNOW YOUR VEHICLE 2. Push and hold the desired HomeLink button until the To do this, push and hold the two outside buttons for 20 indicator light begins to flash after 20 seconds. Do not seconds until the orange indicator flashes. Note that all release the button.
Page 185: General Information
GETTING TO KNOW YOUR VEHICLE 183 If you have any problems, or require assistance, please WARNING! (Continued) call toll-free 1-800-355-3515 or, on the Internet at after 1982. Do not use a garage door opener without HomeLink.com for information or assistance. these safety features.
Page 186: Internal Equipment
184 GETTING TO KNOW YOUR VEHICLE NOTE: • The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not ex- pressly approved by the party responsible for compli- ance could void the user’s authority to operate the device.
Page 187 GETTING TO KNOW YOUR VEHICLE 185 Instrument Panel Drawer There is a storage drawer located in the lower center of the instrument panel. It can be released by pushing the access button above it. The drawer is actuator assisted once the access button is pushed. Pull drawer outward to the fully open position.
Page 188 186 GETTING TO KNOW YOUR VEHICLE Drawer Released Drawer Fully Open CAUTION! The storage drawer must be closed while driving. If left open during a collision, additional damage may occur to property or the drawer mechanism.
Page 189 GETTING TO KNOW YOUR VEHICLE 187 Front Seatback Storage — If Equipped Umbrella Holder The front seatbacks have a storage pocket on some An umbrella holder has been conveniently molded into models. the front door entry scuff moldings. Front Seatback Storage Umbrella Holder...
Page 190 188 GETTING TO KNOW YOUR VEHICLE Second Row Floor Storage Bins 1. To access the storage bin with front seats in the rearward position, place the lock rod in the unlocked The area below the load floor, located in front of the position so the load floor can fold upwards towards second row seats, is available for storage.
Page 191 GETTING TO KNOW YOUR VEHICLE 189 NOTE: • Push the lock rod inward for the locked position. • Pull outward on the lock rod for the unlocked position. 2. Pull the latch located near the second row seat to open the floor panel.
Page 192 190 GETTING TO KNOW YOUR VEHICLE Storage Bin Safety Warning CAUTION! (Continued) Carefully follow these warnings to help prevent personal storage bin cover is left in the open position, front injury or damage to your vehicle: seat adjustment may damage the cover. WARNING! WARNING! •...
Page 193 GETTING TO KNOW YOUR VEHICLE 191 WARNING! (Continued) • Do not operate the storage bin covers while the vehicle is in motion. • Do not use a storage bin latch as a tie down. CAUTION! The storage bin cover must lay flat and be locked to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.
Page 194: Illuminated Vanity Mirrors - If Equipped
192 GETTING TO KNOW YOUR VEHICLE Coat Hooks Illuminated Vanity Mirrors — If Equipped Coat hooks are located along the headliner for the second An illuminated vanity mirror is located on the sun visor. and third row seating positions. The coat hook load limit To use the mirror, rotate the sun visor down and swing is 10 lbs (4.5 kg).
Page 195: Sun Screens - If Equipped
GETTING TO KNOW YOUR VEHICLE 193 Sun Screens — If Equipped Gently pull up on the tab to raise the sun screen. Continue pulling the sun screen until the tab is near the Sun screens are available for second and third row top of the window.
Page 196: Power Outlets
194 GETTING TO KNOW YOUR VEHICLE To lower the sun screen, gently lift the tab upward to NOTE: disengage the hooks, and feed the screen back into the • All accessories connected to the “battery” powered base sill. outlets should be removed or turned off when the Power Outlets vehicle is not in use to protect the battery against discharge.
Page 197 GETTING TO KNOW YOUR VEHICLE 195 The front power outlet is located at the bottom of the instrument panel. Front USB Charge Only Port In addition to the front power outlets, there is also a power outlet located in the rear cargo area. 12 Volt Front Power Outlet The rear power outlet is located in the right rear cargo area.
Page 198 196 GETTING TO KNOW YOUR VEHICLE Rear Power Outlet Power Outlet Fuse Locations NOTE: The USB outlet in the bottom of the instrument 1 — F95A-F95B USB IP 10A panel can be switched from “ignition” only to constant 2 — F85 Cigar Lighter 20A “battery”...
Page 199: Power Inverter - If Equipped
GETTING TO KNOW YOUR VEHICLE 197 WARNING! CAUTION! (Continued) discharge sufficiently to degrade battery life and/or To avoid serious injury or death: prevent the engine from starting. • Only devices designed for use in this type of outlet • Accessories that draw higher power (i.e., coolers, should be inserted into any 12 Volt outlet.
Page 200 198 GETTING TO KNOW YOUR VEHICLE low power devices requiring up to 150 Watts. Certain The Power Inverter is designed with built-in overload high-end video game consoles will exceed this power protection. If the power rating of 150 Watts is exceeded, limit, as will most power tools.
Page 201: Cigar Lighter - If Equipped
GETTING TO KNOW YOUR VEHICLE 199 Cigar Lighter — If Equipped CAUTION! NOTE: Cigar lighters can be purchased at an authorized Do not connect devices with power higher than 180 dealer through MOPAR parts. To ensure proper cigar Watts (15 Amps) to the socket. Do not damage the lighter operation, a MOPAR knob and element must be socket by using unsuitable adaptors.
Page 202: Overhead Storage With Sunglass Storage
200 GETTING TO KNOW YOUR VEHICLE Overhead Storage With Sunglass Storage The door will slowly rotate to the full open position. At the front of the overhead console, a compartment is provided for the storage of one pair of sunglasses. From the closed position, push the door latch to open the compartment.
Page 203: Roof Luggage Rack - If Equipped
GETTING TO KNOW YOUR VEHICLE 201 ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and side rails are designed to carry weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars.
Page 204: Deploying The Crossbars
202 GETTING TO KNOW YOUR VEHICLE The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity. Deploying The Crossbars To deploy the crossbars, completely loosen the thumb screws at both ends of the crossbar and lift the crossbar...
Page 205 GETTING TO KNOW YOUR VEHICLE 203 Bend the crossbar supports at each end, taking care to keep hand clear of pivoting joint. Slide the thumb screw down. Removing Crossbars CAUTION! Use care when removing and handling the crossbars Bending Pivot to prevent damage to the vehicle.
Page 206 204 GETTING TO KNOW YOUR VEHICLE Positioning Crossbars Installing Crossbars Once the crossbar is in place, tighten both thumb screws Deploy and tighten the second crossbar to complete the completely. deployment of the crossbars. NOTE: The crossbars are not identical and have fixed deployment positions.
Page 207: Stowing The Crossbars
GETTING TO KNOW YOUR VEHICLE 205 Stowing The Crossbars Starting with one crossbar, completely loosen the thumb screws at both ends. Lift the crossbar away from the matching letter to remove it from the deployed position. Repeat with the other crossbar. CAUTION! Use care when removing and handling the crossbars to prevent damage to the vehicle.
Page 208 206 GETTING TO KNOW YOUR VEHICLE Then, position the crossbar along the correct side rail. The crossbar will nest fully within the side rail. Make sure the letters on the crossbar align with the matching letters on the side rail. Crossbar To Side Rail Stowing Crossbars...
Page 209 GETTING TO KNOW YOUR VEHICLE 207 Once the driver’s side crossbar is in place, tighten the Repeat the procedure to stow the second crossbar on the thumb screws completely. opposite side. Tightening Crossbar Stowed Crossbars...
Page 210 208 GETTING TO KNOW YOUR VEHICLE NOTE: CAUTION! (Continued) • To help control wind noise, stow the crossbars in the • To avoid damage to the roof rack and vehicle, do side rails when they are not in use. not exceed the maximum roof rack load capacity of 150 lb (68 kg).
Page 211 GETTING TO KNOW YOUR VEHICLE 209 CAUTION! (Continued) • Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack. Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift to a load. This is especially true on large flat loads and may result in damage to the cargo or your vehicle.
Page 213 GETTING TO KNOW YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT CLUSTER ....212 TRIP COMPUTER ..... .229 ▫...
Page 214: Instrument Cluster
212 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER 3.5” EVIC Instrument Cluster...
Page 215 GETTING TO KNOW YOUR INSTRUMENT PANEL 213 7” DID Instrument Cluster...
Page 216: Instrument Cluster Descriptions
214 GETTING TO KNOW YOUR INSTRUMENT PANEL • Instrument Cluster Descriptions The fuel pump symbol points to the side of the vehicle where the fuel door is located. For 3.5” EVIC Cluster and 7” DID Cluster 5. Temperature Gauge 1. Tachometer •...
Page 217: Display
GETTING TO KNOW YOUR INSTRUMENT PANEL 215 DISPLAY WARNING! (Continued) The vehicle can be equipped with a Electronic Vehicle gauge drops back into the normal range and is no Information Center (EVIC), or a Driver Information Dis- longer red. If the gauge remains on the “H”, turn the play (DID), which offers useful information to the driver.
Page 218 216 GETTING TO KNOW YOUR INSTRUMENT PANEL • Fuel Economy Info • Trip (Trip A/Trip B) • Audio • Navigation • Messages • Screen Setup • Speed Warning — 7” DID The system allows the driver to select information by pushing the following buttons mounted on the steering Instrument Cluster Display (EVIC/DID) Control Buttons wheel:...
Page 219: Oil Change Reset
GETTING TO KNOW YOUR INSTRUMENT PANEL 217 • DOWN Arrow Button and hold the OK arrow button for one second to reset displayed/selected features that can be reset. Push and release the DOWN arrow button to scroll downward through the Main Menu Oil Change Reset items.
Page 220: Keysense Cluster Messages - If Equipped
218 GETTING TO KNOW YOUR INSTRUMENT PANEL • To reset the oil change indicator after performing the 1. Without pushing the brake pedal, push the ENGINE scheduled maintenance, refer to the following proce- START/STOP button and cycle the ignition to the dure.
Page 221: Evic/Did Display Menu Items
GETTING TO KNOW YOUR INSTRUMENT PANEL 219 With KeySense in use there will be multiple associated Setting Cluster Display Message messages shown in the following table: Blind Spot “Feature cannot be disabled. Key- Sense in use” Setting Cluster Display Message Forward Col- “Feature cannot be disabled.
Page 222 220 GETTING TO KNOW YOUR INSTRUMENT PANEL Vehicle Info Tire PSI is an information only function and cannot be reset. Push and release the UP or DOWN arrow button until the Vehicle Info icon is highlighted in the EVIC/ Refer to “Tire Pressure Monitoring System (TPMS)” under “Safety”...
Page 223 GETTING TO KNOW YOUR INSTRUMENT PANEL 221 Oil Life (Hold OK Button To Reset) Driver Assist (7” DID) Push and release the UP or DOWN arrow button The “Hold OK to Reset” instruction will be displayed at until the Driver Assist display icon is highlighted in all times, but the following conditions will need to be met the DID cluster display.
Page 224 222 GETTING TO KNOW YOUR INSTRUMENT PANEL – Current Fuel Economy (MPG, L/100 km, or km/l) Audio – The Max and Min values will correspond to the Push and release the UP or DOWN arrow button particular engine requirements until the Audio Menu displays in the EVIC/DID. •...
Page 225 GETTING TO KNOW YOUR INSTRUMENT PANEL 223 Screen Setup 1. Upper Left • None Push and release the UP or DOWN arrow button • Compass (Default) until the Screen Setup Menu displays in the EVIC/ • Outside Temp. DID. Push and release the OK button to enter the submenus.
Page 226 224 GETTING TO KNOW YOUR INSTRUMENT PANEL • Trip A Distance • Time • Trip B Distance • Range • Audio • Average MPG (L/100km, or km/L) • Menu Title (Default) • Current MPG (L/100km, or km/L) • Digital Speed •...
Page 227 GETTING TO KNOW YOUR INSTRUMENT PANEL 225 • Audio 5. Odometer • Digital Speed • Show • Menu Title (Default) • Hide (Odometer will still appear when door is open) 3. Lower Right 6. Defaults • None • Restore • Compass •...
Page 228: Battery Saver On/Battery Saver Mode Message - Electrical Load Reduction Actions - If Equipped
226 GETTING TO KNOW YOUR INSTRUMENT PANEL the instrument cluster, with a number matching the set load reduction actions will take place to extend the speed, with a pop up message to inform the driver driving time and distance of the vehicle. This is done by that the speed warning has been set to the desired reducing power to or turning off non-essential electrical speed.
Page 229 GETTING TO KNOW YOUR INSTRUMENT PANEL 227 • HVAC System NOTE: • The charging system is independent from load reduc- • 115V AC Power Inverter System tion. The charging system performs a diagnostic on the • Audio and Telematics System charging system continuously.
Page 230 228 GETTING TO KNOW YOUR INSTRUMENT PANEL • Installing options like additional lights, upfitter elec- What to do when an electrical load reduction action trical accessories, audio systems, alarms and similar message is present (“Battery Saver On” or “Battery devices. Saver Mode”) •...
Page 231: Trip Computer
GETTING TO KNOW YOUR INSTRUMENT PANEL 229 • Evaluate the latest driving cycles (distance, driving • Shows the elapsed time traveled for Trip A since the time and parking time). last reset. • The vehicle should have service performed if the Trip B message is still present during consecutive trips and •...
Page 232: Warning/Indicator Lights And Messages
230 GETTING TO KNOW YOUR INSTRUMENT PANEL WARNING/INDICATOR LIGHTS AND MESSAGES All active telltales will display first, if applicable. The system check menu may appear different based upon IMPORTANT: The warning/indicator light switches on equipment options and current vehicle status. Some in the instrument panel together with a dedicated mes- telltales are optional and may not appear.
Page 233: Red Telltale Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 231 Red Telltale Lights Air Bag Warning Light Red Telltale What It Means Light Air Bag Warning Light This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to ON/RUN.
Page 234 232 GETTING TO KNOW YOUR INSTRUMENT PANEL Seat Belt Reminder Warning Light Red Telltale What It Means Light Seat Belt Reminder Warning Light When the ignition switch is first turned to ON/RUN, this light will turn on for four to eight seconds as a bulb check.
Page 235 GETTING TO KNOW YOUR INSTRUMENT PANEL 233 Brake Warning Light Red Telltale What It Means Light Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reser- voir.
Page 236 234 GETTING TO KNOW YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capac- Vehicles equipped with the Anti-Lock Brake System ity in the event of a failure to a portion of the hydraulic (ABS) are also equipped with Electronic Brake Force system.
Page 237 GETTING TO KNOW YOUR INSTRUMENT PANEL 235 Battery Charge Warning Light Red Telltale What It Means Light Battery Charge Warning Light This light illuminates when the battery is not charging properly. If it stays on while the en- gine is running, there may be a malfunction with the charging system. Contact your autho- rized dealer as soon as possible.
Page 238 236 GETTING TO KNOW YOUR INSTRUMENT PANEL Coolant Temperature Warning Light Red Telltale What It Means Light Coolant Temperature Warning Light This light warns of an overheated engine condition. If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the vehicle.
Page 239 GETTING TO KNOW YOUR INSTRUMENT PANEL 237 Electric Power Steering Fail Warning Red Telltale What It Means Light Electric Power Steering Fail Warning This light is used to manage the electrical warning of the EPS (Power Steering System). Re- fer to “Power Steering” in “Starting And Operating” for further information.
Page 240 238 GETTING TO KNOW YOUR INSTRUMENT PANEL Electronic Throttle Control (ETC) Warning Light Red Telltale What It Means Light Electronic Throttle Control (ETC) Warning Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a problem is detected while the engine is running, the light will either stay on or flash de- pending on the nature of the problem.
Page 241 GETTING TO KNOW YOUR INSTRUMENT PANEL 239 Oil Temperature Warning Light Red Telltale What It Means Light Oil Temperature Warning Light This telltale indicates engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. Oil Pressure Warning Light Red Telltale What It Means...
Page 242 240 GETTING TO KNOW YOUR INSTRUMENT PANEL Vehicle Security Warning Light — If Equipped Red Telltale What It Means Light Vehicle Security Warning Light This light will flash at a fast rate for approximately 15 seconds when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed.
Page 243 GETTING TO KNOW YOUR INSTRUMENT PANEL 241 NOTE: Continuous driving with the Transmission Tem- NOTE: If you continue operating the vehicle when the perature Warning Light illuminated will eventually cause Transmission Temperature Warning Light is illuminated severe transmission damage or transmission failure. you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.
Page 244 242 GETTING TO KNOW YOUR INSTRUMENT PANEL Liftgate Open Warning Light Red Telltale Light What It Means Liftgate Open Warning Light This indicator will turn on when the liftgate is open. NOTE: If the vehicle is moving there will also be a single chime. Hood Open Warning Light Red Telltale What It Means...
Page 245: Yellow Telltale Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 243 Yellow Telltale Lights Anti-Lock Brake (ABS) Indicator Light Yellow Telltale What It Means Light Anti-Lock Brake (ABS) Indicator Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the igni- tion switch is placed in the ON/RUN position and may stay on for as long as four seconds.
Page 246 244 GETTING TO KNOW YOUR INSTRUMENT PANEL Electronic Stability Control (ESC) Indicator Light — If Equipped Yellow Telltale What It Means Light Electronic Stability Control (ESC) Indicator Light — If Equipped The “ESC Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON/RUN position.
Page 247 GETTING TO KNOW YOUR INSTRUMENT PANEL 245 Electronic Stability Control (ESC) OFF Indicator Light — If Equipped Yellow Telltale What It Means Light Electronic Stability Control (ESC) OFF Indicator Light — If Equipped This light indicates the Electronic Stability Control (ESC) is off. Electronic Park Brake Fail Light Yellow Telltale What It Means...
Page 248 246 GETTING TO KNOW YOUR INSTRUMENT PANEL LaneSense Indicator Light — If Equipped Yellow Telltale What It Means Light LaneSense Indicator Light — If Equipped The LaneSense is solid yellow when the system senses a lane drift situation. The LaneSense is flashing yellow when the system senses the lane has been approached and is in a lane departure situation.
Page 249 GETTING TO KNOW YOUR INSTRUMENT PANEL 247 Low Fuel Indicator Light Yellow Telltale What It Means Light Low Fuel Indicator Light When the fuel level reaches approximately 2.4 gal (9.1 L) this light will turn on, and remain on until fuel is added. Low Washer Fluid Indicator Light —...
Page 250 248 GETTING TO KNOW YOUR INSTRUMENT PANEL Adaptive Cruise Control Alert Indicator Light — If Equipped Yellow Telltale What It Means Light Adaptive Cruise Control Alert Indicator Light This light will turn on when a ACC is not operating and needs service. For further informa- tion, refer to “Adaptive Cruise Control (ACC) —...
Page 251 GETTING TO KNOW YOUR INSTRUMENT PANEL 249 Forward Collision Warning Off Indicator Light — If Equipped Yellow Telltale What It Means Light Forward Collision Off Indicator Light — If Equipped This light indicates the Forward Collision Warning is off.
Page 252 250 GETTING TO KNOW YOUR INSTRUMENT PANEL Engine Check/Malfunction Indicator Light (MIL) Yellow Telltale What It Means Light Engine Check/Malfunction Indicator Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems. The light will illuminate when the ignition is in the ON position before engine start.
Page 253 GETTING TO KNOW YOUR INSTRUMENT PANEL 251 NOTE: Prolonged driving with the Malfunction Indica- NOTE: A malfunctioning catalytic converter, as refer- tor Light (MIL) on could cause damage to the engine enced above, can reach higher temperatures than in control system. It also could affect fuel economy and normal operating conditions.
Page 254 252 GETTING TO KNOW YOUR INSTRUMENT PANEL IMPORTANT: Do not continue driving with one or more Accordingly, when the low tire pressure telltale illumi- flat tires as handling may be compromised. Stop the nates, you should stop and check your tires as soon as vehicle, avoiding sharp braking and steering.
Page 255 GETTING TO KNOW YOUR INSTRUMENT PANEL 253 illuminated. This sequence will continue upon subse- NOTE: The TPMS has been optimized for the original quent vehicle start-ups as long as the malfunction exists. equipment tires and wheels. TPMS pressures and warn- When the malfunction indicator is illuminated, the sys- ing have been established for the tire size equipped on tem may not be able to detect or signal low tire pressure...
Page 256: Green Telltale Lights
254 GETTING TO KNOW YOUR INSTRUMENT PANEL Green Telltale Lights Turn Signal Indicator Lights Green Telltale What It Means Light Turn Signal Indicator Lights The instrument cluster arrow will flash independently for the LEFT or RIGHT turn signal as se- lected, as well as the exterior turn signal lamp(s) (front and rear) as selected when the multi- function lever is moved down (LEFT) or up (RIGHT).
Page 257 GETTING TO KNOW YOUR INSTRUMENT PANEL 255 LaneSense Indicator Light — If Equipped Green Telltale What It Means Light LaneSense Indicator Light The LaneSense indicator is solid green when both lane markings have been detected and the system is “armed” to provide visual warnings in the EVIC/DID and a torque warning in the steering wheel if an unintentional lane departure occurs.
Page 258 256 GETTING TO KNOW YOUR INSTRUMENT PANEL Adaptive Cruise Control (ACC) Set With Target Detected Light — If Equipped Green Telltale What It Means Light Adaptive Cruise Control (ACC) Set With Target Detected Light — If Equipped This light will turn on when the Adaptive Cruise Control speed is SET and the target ve- hicle is detected.
Page 259 GETTING TO KNOW YOUR INSTRUMENT PANEL 257 Park/Headlight ON Indicator Light Green Telltale What It Means Light Park/Headlight ON Indicator Light This indicator will illuminate when the park lights or headlights are turned on. Front Fog Indicator Light — If Equipped Green Telltale What It Means Light...
Page 260: Blue Telltale Lights
258 GETTING TO KNOW YOUR INSTRUMENT PANEL Blue Telltale Lights High Beam Indicator Light Blue Telltale What It Means Light High Beam Indicator Light This indicator shows that the high beam headlights are on. Push the multifunction control lever away from you to switch the headlights to high beam. Pull the lever toward you to switch the headlights back to low beam.
Page 261: White Telltale Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 259 White Telltale Lights Adaptive Cruise Control (ACC) Ready Light — If Equipped White Telltale What It Means Light Adaptive Cruise Control (ACC) Ready Light — If Equipped This light will turn on when the vehicle equipped with Adaptive Cruise Control (ACC) has been turned on and in the READY state.
Page 262 260 GETTING TO KNOW YOUR INSTRUMENT PANEL Electronic Speed Control ON Indicator Light White Telltale What It Means Light Electronic Speed Control ON Indicator Light This light will turn on when the electronic speed control is ON, but a speed has not been set..
Page 263: Onboard Diagnostic System - Obd Ii
GETTING TO KNOW YOUR INSTRUMENT PANEL 261 Speed Warning Light — If Equipped White Warning What It Means Light Speed Warning Light When Speed Warning is turned on the speed warning telltale will illuminate in the instru- ment cluster, with a number matching the set speed. Each time the set speed is exceeded, an audible chime will sound for up to 10 seconds, or until the speed is no longer exceeded.
Page 264: Onboard Diagnostic System (Obd Ii) Cybersecurity
262 GETTING TO KNOW YOUR INSTRUMENT PANEL assist your service technician in making repairs. Al- Onboard Diagnostic System (OBD II) though your vehicle will usually be drivable and not Cybersecurity need towing, see your authorized dealer for service as Your vehicle is required to have an Onboard Diagnostic soon as possible.
Page 265 GETTING TO KNOW YOUR INSTRUMENT PANEL 263 For further information, refer to “Privacy Practices” and WARNING! “Uconnect CyberSecurity” in “All About Uconnect Ac- • ONLY an authorized service technician should con- cess” in your Owner’s Manual Radio Supplement and “Cybersecurity” in “Multimedia”. nect equipment to the OBD II connection port in order to diagnose or service your vehicle.
Page 267 SAFETY CONTENTS ▫ Seat Belt Systems .....304 ACTIVE SAFETY FEATURES....266 ▫...
Page 268: Active Safety Features
266 SAFETY • The ABS motor noise (it may continue to run for a ACTIVE SAFETY FEATURES short time after the stop). Anti-Lock Brake System (ABS) • The clicking sound of solenoid valves. The Anti-Lock Brake System (ABS) provides increased •...
Page 269 SAFETY ABS is designed to function with the OEM tires. Modifi- WARNING! (Continued) cation may result in degraded ABS performance. • Pumping of the Anti-Lock Brakes will diminish Anti-Lock Brake Warning Light their effectiveness and may lead to a collision. Pumping makes the stopping distance longer.
Page 270: Electronic Brake Control System
268 SAFETY Warning Light” does not come on when the ignition Traction Control System (TCS) switch is turned to the ON position, have the light This system monitors the amount of wheel spin of each of repaired as soon as possible. the driven wheels.
Page 271 SAFETY applies optimum pressure to the brakes. This can help WARNING! (Continued) reduce braking distances. The BAS complements the turns, driving on very slippery surfaces, or hydro- anti-lock brake system (ABS). Applying the brakes very planing. The capabilities of a BAS-equipped vehicle quickly results in the best BAS assistance.
Page 272 270 SAFETY Dynamic Steering Torque (DST) Electronic Brake Force Distribution (EBD) Dynamic Steering Torque is a feature of the ESC and EPS This function manages the distribution of the braking modules that provides torque at the steering wheel for torque between the front and rear axles by limiting certain driving conditions in which the ESC module is braking pressure to the rear axle.
Page 273 SAFETY road conditions, leaving the roadway, or striking objects applying the brake of the appropriate wheel(s) to assist in or other vehicles. counteracting the oversteer or understeer condition. En- gine power may also be reduced to help the vehicle WARNING! maintain the desired path.
Page 274 272 SAFETY Malfunction Indicator Light” also flashes when the TCS WARNING! (Continued) is active. If the “ESC Activation/Malfunction Indicator safe, attentive, and skillful driver can prevent acci- Light” begins to flash during acceleration, ease up on the dents. The capabilities of an ESC equipped vehicle accelerator and apply as little throttle as possible.
Page 275 SAFETY ESC Operating Modes To enter the “Partial Off” mode, momentarily push the “ESC Off” switch and the “ESC Off Indicator Light” will NOTE: Depending upon model and mode of operation, illuminate. To turn the ESC on again, momentarily push the ESC system may have multiple operating modes.
Page 276 274 SAFETY position. It should go out with the engine running. If the WARNING! “ESC Activation/Malfunction Indicator Light” comes on • When in “Partial Off” mode, the TCS functionality continuously with the engine running, a malfunction has been detected in the ESC system. If this light remains on of ESC, (except for the limited slip feature de- after several ignition cycles, and the vehicle has been scribed in the TCS section), has been disabled and...
Page 277 SAFETY NOTE: Hill Start Assist (HSA) • The “ESC Activation/Malfunction Indicator Light” The HSA system is designed to mitigate roll back from a complete stop while on an incline. If the driver releases and the “ESC OFF Indicator Light” come on momen- the brake while stopped on an incline, HSA will continue tarily each time the ignition switch is turned ON.
Page 278 276 SAFETY • The gear selection must match vehicle uphill direction WARNING! (Continued) (i.e., vehicle facing uphill is in forward gear; vehicle brake operation to ensure safe operation of the ve- backing uphill is in REVERSE gear). hicle under all road conditions. Your complete atten- •...
Page 279 SAFETY • If disabling HSA using Uconnect Settings, refer to WARNING! (Continued) “Uconnect Settings” in “Multimedia” for further infor- not be enough brake pressure to hold both the mation. vehicle and the trailer on a hill when the brake Rainy Brake Support (RBS) pedal is released.
Page 280: Blind Spot Monitoring (Bsm) - If Equipped
278 SAFETY Trailer Sway Control (TSC) WARNING! TSC uses sensors in the vehicle to recognize an exces- If TSC activates while driving, slow the vehicle sively swaying trailer and will take the appropriate down, stop at the nearest safe location, and adjust the actions to attempt to stop the sway.
Page 281 SAFETY The BSM detection zone covers approximately one lane width on both sides of the vehicle 12 ft (3.8 m). The zone length starts at the outside rear view mirror and extends approximately 10 ft (3 m) beyond the rear bumper of the vehicle.
Page 282 280 SAFETY detections. The BSM warning light may even remain illuminated the entire time the vehicle is in a forward gear. The area on the rear fascia where the radar sensors are located must remain free of snow, ice, and dirt/road contamination so that the BSM system can function properly.
Page 283 SAFETY blockage. After removing the blockage, the following procedure can be used to reset the system: • Cycle the ignition from on to off and then back on. • Ensure that the system detects a blind spot target on each side while driving above 6 mph (10 km/h). If the blockage message is still present after cycling the ignition and driving in traffic, check again for a blockage.
Page 284 282 SAFETY Entering From The Side Entering From The Rear Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h).
Page 285 SAFETY Overtaking Traffic If you pass another vehicle slowly with a relative speed less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 10 mph (16 km/h), the warning light will not illuminate.
Page 286 284 SAFETY Overtaking/Passing Stationary Objects The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in berms, snow banks, car washes etc.
Page 287 SAFETY WARNING! (Continued) system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicle’s mirrors, glance over your shoulder, and use your turn signal before changing lanes. Failure to do so can result in serious injury or death.
Page 288 286 SAFETY NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. Additionally, if the host vehicle is obscured by a flat object on one side the system can false alert on vehicles approaching from the opposite direction.
Page 289 SAFETY alerts when a detected object is present. Whenever an WARNING! (Continued) audible alert is requested, the radio is muted. be sure to check for pedestrians, animals, other Blind Spot Alert Lights/Chime vehicles, obstructions, and blind spots before back- ing up. Failure to do so can result in serious injury or When operating in Blind Spot Alert Lights/Chime mode, death.
Page 290 288 SAFETY present. Whenever an audible alert is requested, the radio General Information is also muted. Turn/hazard signal status is ignored; the This vehicle has systems that operate on radio frequency RCP state always requests the chime. that comply with Part 15 of the Federal Communications Commission (FCC) rules and with Industry Canada Blind Spot Alert Off Standards RSS- GEN/210/220/310.
Page 291: Forward Collision Warning (Fcw) With Mitigation - If Equipped
SAFETY Forward Collision Warning (FCW) With Mitigation and mitigate the potential forward collision. If the driver — If Equipped reacts to the warnings by braking and the system deter- mines that the driver intends to avoid the collision by The Forward Collision Warning (FCW) system with braking but has not applied sufficient brake force, the mitigation provides the driver with audible warnings, system will compensate and provide additional brake...
Page 292 290 SAFETY NOTE: • The minimum speed for FCW activation is 1 mph (2 km/h). • The FCW alerts may be triggered on objects other than vehicles such as guard rails or sign posts based on the course prediction. This is expected and is a part of normal FCW activation and functionality.
Page 293 SAFETY Changing the status of the system is only possible with WARNING! the vehicle at a complete stop. Forward Collision Warning (FCW) is not intended to NOTE: avoid a collision on its own, nor can FCW detect • The FCW system state is kept in memory from one key every type of potential collision.
Page 294 292 SAFETY The default status of FCW is the “Medium” setting and Changing the Active Braking status to “Off” prevents the the Active Braking is in the “On” setting. This allows the system from providing autonomous braking, or addi- system to warn the driver of a possible collision with the tional brake support if the driver is not braking ad- vehicle in front using audible/visual warnings and it equately in the event of a potential frontal collision.
Page 295: Tire Pressure Monitor System (Tpms)
SAFETY FCW Limited Warning Tire Pressure Monitor System (TPMS) If the EVIC/DID displays “ACC/FCW Limited Function- The Tire Pressure Monitor System (TPMS) will warn the ality” or “ACC/FCW Limited Functionality Clean Front driver of a low tire pressure based on the vehicle recom- Windshield”...
Page 296 294 SAFETY The TPMS will warn the driver of a low tire pressure if system receives the updated tire pressures. The vehicle the tire pressure falls below the low-pressure warning may need to be driven for up to 20 minutes above 15 mph limit for any reason, including low temperature effects (24 km/h) in order for the TPMS to receive this informa- and natural pressure loss through the tire.
Page 297 SAFETY CAUTION! CAUTION! (Continued) moisture and dirt from entering the valve stem, • The TPMS has been optimized for the original which could damage the TPMS sensor. equipment tires and wheels. TPMS pressures and warning have been established for the tire size NOTE: equipped on your vehicle.
Page 298 296 SAFETY correct tire pressure using an accurate tire pressure The TPMS consists of the following components: gauge, even if underinflation has not reached the level • Receiver Module to trigger illumination of the “Tire Pressure Monitor- • Four Tire Pressure Monitoring Sensors ing Telltale Light”.
Page 299 SAFETY system receives the updated tire pressures, the system “Tire Pressure Monitoring Telltale Light” will turn off will automatically update and the “Tire Pressure Moni- when the fault condition no longer exists. A system fault toring Telltale Light” will turn off. can occur due to any of the following: NOTE: When filling warm tires, the tire pressure may 1.
Page 300 298 SAFETY 2. If you install the compact or non-matching full size off, as long as no tire pressure is below the low- spare tire in place of a road tire that has a pressure pressure warning limit in any of the four active road below the low-pressure warning limit, a chime will tires.
Page 301 SAFETY The TPMS consists of the following components: • Receiver Module • Four Tire Pressure Monitoring Sensors • Various Tire Pressure Monitoring System messages, which display in the Electronic Vehicle Information Center (EVIC) or Driver Information Display (DID). • Tire Pressure Monitoring Telltale Light Tire Pressure Monitoring Low Pressure Warnings The “Tire Pressure Monitoring Telltale Light”...
Page 302 300 SAFETY update, the pressure values in the graphic display in the longer exists, the “Tire Pressure Monitoring Telltale EVIC/DID will return to their original color, and the Light” will no longer flash, and the “SERVICE SYSTEM “Tire Pressure Monitoring Telltale Light” will turn off. message will no longer display, and a pressure value will The vehicle may need to be driven for up to 20 minutes display in place of the dashes.
Page 303 SAFETY Vehicles With Compact Spare 4. For each subsequent ignition cycle, a chime will sound, the “TPMS Telltale Light” will flash on and off 1. The compact spare tire does not have a tire pressure for 75 seconds and then remain on solid, and the monitoring sensor.
Page 304: Occupant Restraint Systems
302 SAFETY General Information Occupant Restraint Systems Features • Seat Belt Systems This device complies with Part 15 of the FCC rules and RSS-210 of Industry Canada. Operation is subject to the • Supplemental Restraint Systems (SRS) Air Bags following two conditions: •...
Page 305 SAFETY move the seat as far back as possible and use the 7. The driver and front passenger seats should be moved proper child restraint. (Refer to “Child Restraints”) back as far as practical to allow the Advanced Front Air Bags room to inflate. 3.
Page 306: Seat Belt Systems
304 SAFETY ejection and the risk of injury caused by striking the WARNING! (Continued) inside of the vehicle. Everyone in a motor vehicle should Air Bag can cause death or serious injury to a child be belted at all times. 12 years or younger, including a child in a rear- Driver And Passenger BeltAlert (If Equipped) facing child restraint.
Page 307 SAFETY position the Seat Belt Reminder Light will turn on and driver and occupied outboard front seat passenger seat remain on until both outboard front seat belts are buck- belts are buckled. The driver should instruct all occu- led. The outboard front passenger seat BeltAlert is not pants to buckle their seat belts.
Page 308 306 SAFETY BeltAlert can be activated or deactivated by your autho- will lock and reduce your risk of striking the inside of the rized dealer. FCA US LLC does not recommend deacti- vehicle or being thrown out of the vehicle. vating BeltAlert.
Page 309 SAFETY WARNING! (Continued) WARNING! (Continued) • It is dangerous to ride in a cargo area, inside or • Two people should never be belted into a single outside of a vehicle. In a collision, people riding in seat belt. People belted together can crash into one these areas are more likely to be seriously injured another in a collision, hurting one another badly.
Page 310 308 SAFETY WARNING! (Continued) WARNING! (Continued) • A seat belt that is buckled into the wrong buckle • A shoulder belt placed behind you will not protect will not protect you properly. The lap portion could you from injury during a collision. You are more ride too high on your body, possibly causing inter- likely to hit your head in a collision if you do not nal injuries.
Page 311 SAFETY Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, and next to your arm in the rear seat (for vehicles equipped with a rear seat).
Page 312 310 SAFETY Inserting Latch Plate Into Buckle Positioning The Lap Belt 4. Position the lap belt so that it is snug and lies low 5. Position the shoulder belt across the shoulder and across your hips, below your abdomen. To remove chest with minimal, if any slack so that it is comfort- slack in the lap belt portion, pull up on the shoulder able and not resting on your neck.
Page 313 SAFETY stowed position. If necessary, slide the latch plate 4. Continue to slide the latch plate up until it clears the down the webbing to allow the seat belt to retract folded webbing and the seat belt is no longer twisted. fully.
Page 314 312 SAFETY NOTE: The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release but- ton. To verify the shoulder belt anchorage is latched, pull downward on the shoulder belt anchorage until it is locked into position.
Page 315 SAFETY 1. Remove the mini-latch plate and regular latch plate 2. Grasp the mini-latch plate and pull the seat belt over from its stowed position in the headliner slightly the seat. behind the third row seat. Mini-Latch Plate Mini-Latch Stowage...
Page 316 314 SAFETY 3. Route the shoulder belt to the inside of the left head 4. When the seat belt is long enough to fit, insert the restraint. mini-latch plate into the mini-buckle until you hear a “click.” Mini-Latch And Buckle Connected Connect Mini-Latch To Buckle...
Page 317 SAFETY 5. Sit back in seat. Slide the regular latch plate up the webbing as far as necessary to allow the seat belt to go around your lap. Rear Center Seat Belt Buckled 1 — Seat Belt Latch Plate 2 — Seat Belt Buckle 1 —...
Page 318 316 SAFETY belt. To loosen the lap belt if it is too tight, pull on the WARNING! lap belt. A snug seat belt reduces the risk of sliding • If the mini-latch plate and mini-buckle are not under the seat belt in a collision. properly connected when the seat belt is used by an 8.
Page 319 SAFETY Seat Belt Extender. The Seat Belt Extender should be used Seat Belts And Pregnant Women only if the existing seat belt is not long enough. When the Seat Belt Extender is not required for a different occu- pant, it must be removed. WARNING! •...
Page 320 318 SAFETY Position the lap belt snug and low below the abdomen The pretensioners are triggered by the Occupant Re- and across the strong bones of the hips. Place the straint Controller (ORC). Like the air bags, the preten- shoulder belt across the chest and away from the neck. sioners are single use items.
Page 321 SAFETY Restraints” section of this manual. The table below defines the type of feature for each seating position. 8 Passenger With Stow N Go Second Row Seats • ALR — Switchable Automatic Locking Retractor If the passenger seating position is equipped with an ALR and is being used for normal usage, only pull the 7 Passenger With Stow N Go Second Row Seats seat belt webbing out far enough to comfortably wrap...
Page 322 320 SAFETY sound as the seat belt retracts. Allow the webbing to WARNING! (Continued) retract completely in this case and then carefully pull out 12 years or younger, including a child in a rear- only the amount of webbing necessary to comfortably facing child restraint.
Page 323: Supplemental Restraint System (Srs)
SAFETY Mode and activate the vehicle sensitive (emergency) Supplemental Restraint System (SRS) locking mode. Air Bag System Components Your vehicle may be equipped with the following air bag WARNING! system components: • The seat belt assembly must be replaced if the •...
Page 324 322 SAFETY • Seat Belt Pretensioners • Seat Belt Buckle Switch • Seat Track Position Sensors • Occupant Classification System Advanced Front Air Bags This vehicle has Advanced Front Air Bags for both the driver and front passenger as a supplement to the seat belt restraint systems.
Page 325 SAFETY output appropriate to the severity and type of collision as WARNING! determined by the Occupant Restraint Controller (ORC), • Being too close to the steering wheel or instrument which may receive information from the front impact sensors or other system components. panel during Advanced Front Air Bag deployment could cause serious injury, including death.
Page 326 324 SAFETY This vehicle is equipped with a right front passenger WARNING! (Continued) Occupant Classification System (“OCS”) that is designed designed to open only when the air bags are to provide Passenger Advanced Front Air Bag output inflating. appropriate to the occupant’s seated weight input, as •...
Page 327 SAFETY vehicle damage — for example, some pole collisions, The steering wheel hub trim cover and the upper right truck underrides, and angle offset collisions. side of the instrument panel separate and fold out of the way as the air bags inflate to their full size. The Advanced On the other hand, depending on the type and location of Front Air Bags fully inflate in less time than it takes to impact, Advanced Front Air Bags may deploy in crashes...
Page 328 326 SAFETY • Occupant Classification Module (OCM) and Sensor The OCS will NOT prevent deployment of the Passenger located in the front passenger seat Advanced Front Air Bag. The OCS may reduce the inflation rate of the Passenger Advanced Front Air Bag if •...
Page 329 SAFETY including a rear-facing child restraint, in the front pas- Front Passenger Seat Front Passenger Air senger seat. Occupant Status Bag Output Rear-facing child restraint Reduced-power deploy- WARNING! ment • Never place a rear-facing child restraint in front of Child, including a child in Reduced-power deploy- a forward-facing child re-...
Page 330 328 SAFETY ORC. The ORC uses the classification to determine whether the Passenger Advanced Front Air Bag inflation rate should be adjusted. In order for the OCS to operate as designed, it is important for the front passenger to be seated properly and properly wearing the seat belt.
Page 331 SAFETY Do not decrease OR increase the front passenger’s Examples of improper front passenger seating include: seated weight on the front passenger seat • The front passenger’s weight is transferred to another The front passenger’s seated weight must be properly part of the vehicle (like the door, arm rest or instru- positioned on the front passenger seat.
Page 332 330 SAFETY • Anything that may decrease or increase the front passenger’s seated weight. The OCS determines the front passenger’s most probable classification. If an occupant in the front passenger seat is seated improperly, the occupant may provide an output signal to the OCS that is different from the occupant’s properly seated weight input, for example: Not Seated Properly...
Page 333 SAFETY Not Seated Properly Not Seated Properly...
Page 334 332 SAFETY WARNING! (Continued) signal to the OCS that is different from the occu- pant’s properly seated weight input. This may result in serious injury or death in a collision. • Always wear your seat belt and sit properly, with the seatback in an upright position, your back against the seatback, sitting upright, facing for- ward, in the center of the seat, with your feet...
Page 335 SAFETY Do not make any modifications to the front passenger WARNING! (Continued) seat components, assembly, or to the seat cover. If the properly, which may result in serious injury or seat, trim cover, or cushion needs service for any reason, death in a collision.
Page 336 334 SAFETY • At no time should any Supplemental Restraint System Knee Impact Bolsters (SRS) component or SRS related component or fastener The Knee Impact Bolsters help protect the knees of the be modified or replaced with any part except those driver and front passenger, and position the front occu- which are approved by FCA US LLC.
Page 337 SAFETY Bag mounted in the instrument panel below the glove compartment. The Supplemental Knee Air Bags provide enhanced protection during a frontal impact by working together with the seat belts, pretensioners, and Advanced Front Air Bags. Supplemental Side Air Bags Your vehicle is equipped with two types of side air bags: 1.
Page 338 336 SAFETY deploys through the seat seam into the space between the occupant and the door. The SAB moves at a very high speed and with such a high force that it could injure occupants if they are not seated properly, or if items are positioned in the area where the SAB inflates.
Page 339 SAFETY The SABICs deploy downward, covering the side win- WARNING! dows. An inflating SABIC pushes the outside edge of the • Your vehicle is equipped with left and right trim out of the way and covers the window. The SABICs inflate with enough force to injure occupants if they are Supplemental Side Air Bag Inflatable Curtains not belted and seated properly, or if items are positioned...
Page 340 338 SAFETY The SABICs and SABs (“Side Air Bags”) are designed to help keep you in position, away from inflating Side Air activate in certain side impacts and certain rollover Bags. To get the best protection from the Side Air Bags, events.
Page 341 SAFETY The Side Air Bags will not deploy in all side collisions, WARNING! (Continued) including some collisions at certain angles, or some side properly. In some collisions, Side Air Bags won’t collisions that do not impact the area of the passenger deploy at all.
Page 342 340 SAFETY Air Bags is appropriate, the rollover sensing system will normally heal quickly. However, if you haven’t healed also deploy the seat belt pretensioners on both sides of significantly within a few days, or if you have any the vehicle. blistering, see your doctor immediately.
Page 343 SAFETY on the nature of the event, the ORC will determine WARNING! whether to have the Enhanced Accident Response Sys- tem perform the following functions: Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, •...
Page 344 342 SAFETY OFF. Carefully check the vehicle for fuel leaks in the The ORC contains a backup power supply system that engine compartment and on the ground near the engine may deploy the air bags even if the battery loses power or compartment and fuel tank before resetting the system it becomes disconnected prior to deployment.
Page 345 SAFETY free, if any of the following occurs, have an authorized WARNING! dealer service the air bag system immediately. Ignoring the Air Bag Warning Light in your instru- • The Air Bag Warning Light does not come on during ment panel could mean you won’t have the air bags the four to eight seconds when the ignition switch is to protect you in a collision.
Page 346 344 SAFETY If the Redundant Air Bag Warning Light comes on WARNING! (Continued) intermittently or remains on while driving have an modify the front bumper, vehicle body structure, or authorized dealer service the vehicle immediately. For add aftermarket side steps or running boards. additional information regarding the Redundant Air Bag •...
Page 347 SAFETY Event Data Recorder (EDR) These data can help provide a better understanding of the circumstances in which crashes and injuries occur. This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in NOTE: EDR data are recorded by your vehicle only if a certain crash or near crash-like situations, such as an air non-trivial crash situation occurs;...
Page 348: Child Restraints
346 SAFETY Child Restraints WARNING! Everyone in your vehicle needs to be buckled up at all In a collision, an unrestrained child can become a times, including babies and children. projectile inside the vehicle. The force required to Every state in the United States, and every Canadian hold even an infant on your lap could become so province, requires that small children ride in proper great that you could not hold the child, no matter...
Page 349 SAFETY There are different sizes and types of restraints for NOTE: children from newborn size to the child almost large • For additional information, refer to www.seatcheck.org or enough for an adult safety belt. Always check the child call 1-866-732-8243. seat Owner’s Manual to make sure you have the correct •...
Page 350 348 SAFETY Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Infants and Children who are two years old or Either an Infant Carrier or a Convertible Toddlers younger and who have not reached the Child Restraint, facing rearward in the rear height or weight limits of their child re- seat of the vehicle...
Page 351 SAFETY Infants And Child Restraints WARNING! Safety experts recommend that children ride rear-facing • Never place a rear-facing child restraint in front of in the vehicle until they are two years old or until they an air bag. A deploying passenger Advanced Front reach either the height or weight limit of their rear-facing Air Bag can cause death or serious injury to a child child restraint.
Page 352 350 SAFETY Older Children And Child Restraints WARNING! Children who are two years old or who have outgrown Do not install a rear-facing car seat using a rear support their rear-facing convertible child seat can ride forward- leg in this vehicle. The floor of this vehicle is not facing in the vehicle.
Page 353 SAFETY seat. The child and belt-positioning booster seat are held WARNING! (Continued) in the vehicle by the seat belt. • When your child restraint is not in use, secure it in the vehicle with the seat belt or LATCH anchor- WARNING! ages, or remove it from the vehicle.
Page 354 352 SAFETY 2. Do the child’s knees bend comfortably over the front WARNING! of the vehicle seat – while they are still sitting all the way back? Never allow a child to put the shoulder belt under an arm or behind their back. In a crash, the shoulder belt 3.
Page 355 SAFETY Recommendations For Attaching Child Restraints Restraint Type Combined Use any attachment method shown with an “X” Below Weight of the LATCH – Seat Belt Only LATCH – Seat Belt + Top Child + Child Lower Anchors Lower Anchors Tether Anchor Restraint Only + Top Tether...
Page 356 354 SAFETY Lower Anchors And Tethers For CHildren Your vehicle is equipped with the child restraint anchor- (LATCH) Restraint System age system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCH- equipped child seats.
Page 357 SAFETY LATCH Positions For Installing Child Restraints In This Vehicle 8 Passenger With Stow N Go • Lower Anchorage Symbol 2 anchorages per seating position 7 Passenger With Stow N Go • Top Tether Anchorage Symbol...
Page 358 356 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Frequently Asked Questions What is the weight limit (child’s 65 lbs (29.5 kg) Use the LATCH anchorage system weight + weight of the child re- until the combined weight of the straint) for using the LATCH an- child and the child restraint is chorage system to attach the child...
Page 359 SAFETY Frequently Asked Questions Can two child restraints be at- Never “share” a LATCH anchorage tached using a common lower with two or more child restraints. LATCH anchorage? If the center position does not have dedicated LATCH lower anchor- ages, use the seat belt to install a child seat in the center position next to a child seat using the LATCH anchorages in an outboard...
Page 360 358 SAFETY Frequently Asked Questions Can the head restraints be re- The 2nd row head restraints on moved? bench and fixed quad seats and in the center seat (if equipped), are removable. 2nd row outboard stow ’n go head restraints are not re- movable.
Page 361 SAFETY Locating LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion.
Page 362 360 SAFETY right outboard position and in the center of the 60% seat for either the center or left outboard seating position. All tether anchorages are located on the back of the seat, near the floor. LATCH Anchorages (Third Row 60/40 Anchorages Shown) Locating Tether Anchorages Tether Strap Anchorages (Third Row 60/40 Anchorage...
Page 363 SAFETY LATCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage.
Page 364 362 SAFETY center position blocks the outboard LATCH anchors or To install a LATCH-Compatible Child Restraint seat belt, do not install a child seat in that outboard If the selected seating position has a Switchable Auto- position. matic Locking Retractor (ALR) seat belt, stow the seat belt, following the instructions below.
Page 365 SAFETY 3. Attach the lower hooks or connectors of the child How To Stow An Unused ALR Seat Belt restraint to the lower anchorages in the selected seat- When using the LATCH attaching system to install a ing position. child restraint, stow all ALR seat belts that are not being used by other occupants or being used to secure child 4.
Page 366 364 SAFETY Installing Child Restraints Using The Vehicle Seat WARNING! Belt • Improper installation of a child restraint to the The seat belts in the passenger seating positions are LATCH anchorages can lead to failure of the re- equipped with a Switchable Automatic Locking Retractor straint.
Page 367 SAFETY Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle 8 Passenger With Second Row Stow N Go Seats • ALR = Switchable Automatic Locking Retractor • Top Tether Anchorage Symbol 7 Passenger With Second Row Stow N Go Seats...
Page 368 366 SAFETY Frequently Asked Question About Installing Child Restraints With Seat Belts Frequently Asked Questions What is the weight limit (child’s weight + Weight limit of the Always use the tether anchor when using weight of the child restraint) for using the Child Restraint the seat belt to install a forward facing Tether Anchor with the seat belt to attach a...
Page 369 SAFETY Frequently Asked Questions Can the buckle stalk be twisted to tighten Do not twist the buckle stalk in a seating the seat belt against the belt path of the position with an ALR retractor. child restraint? NOTE: If the folding, non-adjustable head restraint in- Installing A Child Restraint With A Switchable terferes with the installation of the child restraint, the Automatic Locking Retractor (ALR)
Page 370 368 SAFETY 3. Slide the latch plate into the buckle until you hear a 8. If the child restraint has a top tether strap and the “click.” seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether 4.
Page 371 SAFETY Installing Child Restraints Using The Top Tether Tether Anchorage Attachment Anchorage: 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. WARNING! You may need to move the seat forward to provide better access to the tether anchorage.
Page 372 370 SAFETY 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts.
Page 373 SAFETY WARNING! • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • If your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap.
Page 374 372 SAFETY To connect the tether strap hook to the tether anchorage for either seating position on the 60% third row seat: 1. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. 2.
Page 375: Transporting Pets
SAFETY Transporting Pets Air Bags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts.
Page 376: Exhaust Gas
374 SAFETY Exhaust Gas WARNING! • Do not leave children or animals inside parked WARNING! vehicles in hot weather. Interior heat build-up may Exhaust gases can injure or kill. They contain carbon cause serious injury or death. monoxide (CO), which is colorless and odorless. •...
Page 377: Safety Checks You Should Make Inside The Vehicle
SAFETY Safety Checks You Should Make Inside The WARNING! (Continued) Vehicle • If it is necessary to sit in a parked vehicle with the Seat Belts engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the Inspect the seat belt system periodically, checking for blower at high speed.
Page 378 376 SAFETY have the system inspected at an authorized dealer as cannot slip out of position and interfere with the pedals soon as possible. This light will illuminate with a or impair safe operation of your vehicle in other ways. single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault WARNING!
Page 379: Periodic Safety Checks You Should Make Outside
SAFETY Periodic Safety Checks You Should Make Outside WARNING! (Continued) The Vehicle • Check mounting of mats on a regular basis. Always Tires properly reinstall and secure floor mats that have been removed for cleaning. Examine tires for excessive tread wear and uneven wear •...
Page 380 378 SAFETY Door Latches Check for proper closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid (if equipped), or brake fluid leaks are suspected.
Page 381: Starting And Operating
STARTING AND OPERATING CONTENTS STARTING PROCEDURES ....383 ENGINE BREAK-IN RECOMMENDATIONS . . .388 ▫ Normal Starting..... . .383 PARKING BRAKE .
Page 382 380 STARTING AND OPERATING ▫ To Cancel ......415 SPEED CONTROL — IF EQUIPPED ..405 ▫...
Page 383 STARTING AND OPERATING 381 ▫ ParkSense Display .....450 PARKSENSE REAR PARK ASSIST — IF EQUIPPED ......436 ▫...
Page 384 382 STARTING AND OPERATING ▫ LaneSense Operation ....487 ▫ Trailer Towing Weights (Maximum Trailer Weight Ratings) ......511 ▫...
Page 385: Starting Procedures
STARTING AND OPERATING 383 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust both leave the ignition of a vehicle equipped with inside and outside mirrors, and fasten your seat belts. Keyless Enter-N-Go in the ACC or ON/RUN mode. A child could operate power windows, other con- WARNING! trols, or move the vehicle.
Page 386: Cold Weather Operation (Below -22°F Or −30°C)
384 STARTING AND OPERATING • Push the ENGINE START/STOP button once to place 2. Press and hold the brake pedal while pushing the ENGINE START/STOP button once. the ignition to the ACC position (EVIC/DID will display “ACC”), 3. The system takes over and attempts to start the •...
Page 387: After Starting - Warming Up The Engine
STARTING AND OPERATING 385 1. Install a battery charger or jumper cables to the battery After Starting — Warming Up The Engine to ensure a full battery charge during the crank cycle. The idle speed is controlled automatically and it will decrease as the engine warms up.
Page 388: To Turn Off The Engine Using Engine Start/Stop Button
386 STARTING AND OPERATING The ignition switch position will remain in the ACC WARNING! (Continued) position until the gear selector is in PARK and the • If the vehicle has a discharged battery, booster button is pushed twice to the OFF position. If the gear cables may be used to obtain a start from a booster selector is not in PARK and the ENGINE START/ battery or the battery in another vehicle.
Page 389 STARTING AND OPERATING 387 Connect the cord to a 110-115 Volt AC electrical outlet 4. After the vehicle is running, reattach the cord to the with a grounded, three-wire extension cord. Velcro strap and properly stow away behind the passenger’s side headlamp. For ambient temperatures below 0°F (-18°C), the engine block heater is recommended.
Page 390: Engine Break-In Recommendations
388 STARTING AND OPERATING The engine oil installed in the engine at the factory is a WARNING! high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate Remember to disconnect the engine block heater conditions under which vehicle operations will occur. For cord before driving.
Page 391: Parking Brake
STARTING AND OPERATING 389 PARKING BRAKE Electric Park Brake (EPB) Your vehicle is equipped with an Electric Park Brake System (EPB) that offers simple operation, and some additional features that make the park brake more con- venient and useful. The park brake is primarily intended to prevent the vehicle from rolling while parked.
Page 392 390 STARTING AND OPERATING pedal while you apply the park brake, you may notice a The park brake will release automatically when the small amount of brake pedal movement. The park brake ignition is cycled to the RUN position, the transmission is can be applied even when the ignition switch is OFF, in DRIVE or REVERSE, and the driver seat belt is however, it can only be released when the ignition switch...
Page 393 STARTING AND OPERATING 391 NOTE: When parking on a hill, it is important to turn the WARNING! (Continued) front wheels toward the curb on a downhill grade and • Never leave children alone in a vehicle, or with away from the curb on an uphill grade. Apply the park access to an unlocked vehicle.
Page 394 392 STARTING AND OPERATING If exceptional circumstances should make it necessary to WARNING! (Continued) engage the park brake while the vehicle is in motion, • Always fully apply the parking brake when leav- push on the electric park brake switch for as long as ing your vehicle, or it may roll and cause damage or engagement is desired.
Page 395 STARTING AND OPERATING 393 Auto Park Brake and brake pedal is pressed. Once manually bypassed, SafeHold will be enabled again once the vehicle reaches The Electric Park Brake can be programmed to be applied 12 mph (20 km/h) or the ignition is cycled to the OFF automatically whenever the vehicle is at a standstill and position and back to ON again.
Page 396: Automatic Transmission
394 STARTING AND OPERATING • Apply the Electric Park Brake Switch. system will guide you through the steps necessary to retract the EPB actuator in order to perform rear brake service. WARNING! Brake Service Mode has requirements that must be met in You can be badly injured working on or around a order to be activated: motor vehicle.
Page 397 STARTING AND OPERATING 395 CAUTION! (Continued) WARNING! (Continued) • Do not shift between PARK, REVERSE, NEU- • Unintended movement of a vehicle could injure TRAL, or DRIVE when the engine is above idle those in or near the vehicle. As with all vehicles, speed.
Page 398: Ignition Park Interlock
396 STARTING AND OPERATING transmission in PARK. This system also locks the trans- WARNING! (Continued) mission in PARK whenever the ignition switch is in the seriously or fatally injured. Children should be OFF position. warned not to touch the parking brake, brake pedal Brake/Transmission Shift Interlock System or the transmission gear selector.
Page 399 STARTING AND OPERATING 397 gear based on vehicle speed. The transmission gear range NOTE: In the event of a mismatch between the gear (PRNDL) is displayed both above the gear selector and in selector position and the actual transmission gear (for the Electronic Vehicle Information Center (EVIC) or the example, driver selects PARK while driving), the position Driver Information Display (DID).
Page 400: Gear Ranges
398 STARTING AND OPERATING Only shift from DRIVE to PARK or REVERSE when the Gear Ranges accelerator pedal is released and the vehicle is stopped. DO NOT race the engine when shifting from PARK or Be sure to keep your foot on the brake pedal when NEUTRAL into another gear range.
Page 401 STARTING AND OPERATING 399 When parking on a hill, apply the parking brake before WARNING! (Continued) shifting the transmission to PARK. As an added precau- vehicle could accelerate quickly forward or in re- tion, turn the front wheels toward the curb on a downhill verse.
Page 402 400 STARTING AND OPERATING WARNING! (Continued) CAUTION! • When leaving the vehicle, always make sure the • Before moving the transmission gear selector out of ignition is in the OFF position, remove the Key Fob PARK, you must start the engine and also press the from the vehicle, and lock the vehicle.
Page 403 STARTING AND OPERATING 401 REVERSE (R) CAUTION! This range is for moving the vehicle backward. Shift into Towing the vehicle, coasting, or driving for any other REVERSE only after the vehicle has come to a complete reason with the transmission in NEUTRAL can cause stop.
Page 404 402 STARTING AND OPERATING and/or expand the range of torque converter clutch LOW (L) engagement. This is done to prevent transmission dam- Use this range for engine braking when descending very age due to overheating. steep grades. In this range, the transmission will down- shift for increased engine braking.
Page 405 STARTING AND OPERATING 403 In the event of a momentary problem, the transmission NOTE: Even if the transmission can be reset, we recom- can be reset to regain all forward gears by performing the mend that you visit your authorized dealer at your following steps: earliest possible convenience.
Page 406: Active Noise Cancellation
404 STARTING AND OPERATING NOTE: The torque converter clutch will not engage until POWER STEERING the transmission fluid is warm (usually after 1 to 3 miles The electric power steering system will give you good [2 to 5 km] of driving). Because the engine speed is higher vehicle response and increased ease of maneuverability when the torque converter clutch is not engaged, it may in tight spaces.
Page 407: Speed Control - If Equipped
STARTING AND OPERATING 405 SPEED CONTROL — IF EQUIPPED If the “SERVICE POWER STEERING OR When engaged, the Speed Control takes over accelerator POWER STEERING ASSIST OFF - SERVICE operations at speeds greater than 25 mph (40 km/h). SYSTEM” message and a steering wheel icon are displayed on the EVIC/DID screen, it indicates that The Speed Control buttons are located on the right side of the vehicle needs to be taken to the dealer for service.
Page 408: To Activate
406 STARTING AND OPERATING NOTE: In order to ensure proper operation, the Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Speed Control System can be reactivated by pushing the Speed Control ON/OFF button and resetting the desired vehicle set speed.
Page 409: To Set A Desired Speed
STARTING AND OPERATING 407 To Vary The Speed Setting WARNING! To Increase Speed Leaving the Speed Control system on when not in When the Speed Control is set, you can increase speed by use is dangerous. You could accidentally set the pushing the SET + button.
Page 410 408 STARTING AND OPERATING Metric Speed (km/h) U.S. Speed (mph) • Pushing the SET + button once will result in a 1 km/h • Pushing the SET - button once will result in a 1 mph increase in set speed. Each subsequent tap of the decrease in set speed.
Page 411: To Accelerate For Passing
STARTING AND OPERATING 409 To Accelerate For Passing ADAPTIVE CRUISE CONTROL (ACC) — IF EQUIPPED Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Adaptive Cruise Control (ACC) increases the driving convenience provided by cruise control while traveling To Resume Speed on highways and major roadways.
Page 412 410 STARTING AND OPERATING • If the ACC sensor detects a vehicle ahead, ACC will You can change the mode by using the Cruise Control apply limited braking or accelerate (not to exceed the buttons. The two control modes function differently. original set speed) automatically to maintain a preset Always confirm which mode is selected.
Page 413: Adaptive Cruise Control (Acc) Operation
STARTING AND OPERATING 411 WARNING! (Continued) WARNING! (Continued) • The ACC system: You should switch off the ACC system: • Does not react to pedestrians, oncoming vehicles, • When driving in fog, heavy rain, heavy snow, sleet, and stationary objects (e.g., a stopped vehicle in a heavy traffic, and complex driving situations (i.e., traffic jam or a disabled vehicle).
Page 414: Activating Adaptive Cruise Control (Acc)
412 STARTING AND OPERATING NOTE: Any chassis/suspension or tire size modifications to the vehicle will effect the performance of the Adaptive Cruise Control and Forward Collision Warning System. Activating Adaptive Cruise Control (ACC) You can only engage ACC if the vehicle speed is above 0 mph (0 km/h).
Page 415: To Activate/Deactivate
STARTING AND OPERATING 413 NOTE: You cannot engage ACC under the following conditions: • When you apply the brakes. • When the parking brake is set. • When the automatic transmission is in PARK, RE- VERSE or NEUTRAL. • When the vehicle speed is outside of the speed range. •...
Page 416: To Set A Desired Acc Speed
414 STARTING AND OPERATING WARNING! (Continued) You could lose control and have a collision. Always leave the system off when you are not using it. To Set A Desired ACC Speed When the vehicle reaches the speed desired, push the SET + button or the SET - button and release.
Page 417: To Cancel
STARTING AND OPERATING 415 • The Electronic Stability Control/Traction Control Sys- Remove your foot from the accelerator pedal. If you do not, the vehicle may continue to accelerate beyond the set tem (ESC/TCS) activates. speed. If this occurs: • The vehicle parking brake is applied. •...
Page 418: To Resume
416 STARTING AND OPERATING To Resume WARNING! If there is a set speed in memory push the RES (resume) The Resume function should only be used if traffic button and then remove your foot from the accelerator and road conditions permit. Resuming a set speed pedal.
Page 419 STARTING AND OPERATING 417 • If the button is continually pushed, the set speed will The drivers preferred units can be selected through the Uconnect Settings if equipped. Refer to “Uconnect Set- continue to increase in 10 km/h increments until the tings”...
Page 420 418 STARTING AND OPERATING • If the button is continually pushed, the set speed will • When you use the SET - button to decelerate, if the continue to decrease in 5 mph decrements until the engine’s braking power does not slow the vehicle button is released.
Page 421: Setting The Following Distance In Acc
STARTING AND OPERATING 419 Setting The Following Distance In ACC The specified following distance for ACC can be set by varying the distance setting between four bars (longest), three bars (long), two bars (medium) and one bar (short). Using this distance setting and the vehicle speed, ACC calculates and sets the distance to the vehicle ahead.
Page 422 420 STARTING AND OPERATING Distance Setting 3 Bars (Long) Distance Setting 2 Bars (Medium)
Page 423 STARTING AND OPERATING 421 To decrease the distance setting, push the Distance Set- ting — Decrease button and release. Each time the button is pushed, the distance setting decreases by one bar (shorter). If there is no vehicle ahead, the vehicle will maintain the set speed.
Page 424 422 STARTING AND OPERATING • The system disengages. (Refer to the information on ACC Activation). The maximum braking applied by ACC is limited; how- ever, the driver can always apply the brakes manually, if necessary. NOTE: The brake lights will illuminate whenever the ACC system applies the brakes.
Page 425: Overtake Aid
STARTING AND OPERATING 423 Overtake Aid NOTE: After the ACC system holds your vehicle at a standstill for approximately 3 consecutive minutes, the When driving with ACC engaged and following a ve- parking brake will be activated, and the ACC system will hicle, the system will provide an additional acceleration be cancelled.
Page 426: Adaptive Cruise Control (Acc) Menu
424 STARTING AND OPERATING Adaptive Cruise Control (ACC) Menu Push the SET + or the SET- button (located on the steering wheel) and the following will display in the EVIC/DID: The EVIC/DID displays the current ACC system set- tings. The EVIC/DID is located in the center of the ACC SET instrument cluster.
Page 427: Display Warnings And Maintenance
STARTING AND OPERATING 425 Display Warnings And Maintenance vehicle has left these areas. Under rare conditions, when the radar is not tracking any vehicles or objects in its path “Wipe Front Radar Sensor In Front Of Vehicle” this warning may temporarily occur. Warning NOTE: If the “ACC/FCW Unavailable Wipe Front Radar The “ACC/FCW Unavailable Wipe Front Radar Sensor”...
Page 428 426 STARTING AND OPERATING • Do not remove any screws from the sensor. Doing so NOTE: If the “ACC/FCW Unavailable Wipe Front Ra- could cause an ACC system malfunction or failure and dar Sensor” message occurs frequently (e.g. more than require a sensor realignment.
Page 429 STARTING AND OPERATING 427 The “ACC/FCW Limited Functionality Clean Front NOTE: If the “ACC/FCW Limited Functionality Clean Windshield” message can sometimes be displayed while Front Windshield” message occurs frequently (e.g. more driving in adverse weather conditions. The ACC/FCW than once on every trip) without any snow, rain, mud, or system will recover after the vehicle has left these areas.
Page 430: Precautions While Driving With Acc
428 STARTING AND OPERATING Precautions While Driving With ACC In certain driving situations, ACC may have detection issues. In these cases, ACC may brake late or unexpect- edly. The driver needs to stay alert and may need to intervene. Towing A Trailer Towing a trailer is not advised when using ACC.
Page 431 STARTING AND OPERATING 429 the vehicle is out of the curve the system will resume Using ACC On Hills your original Set Speed. This is a part of normal ACC When driving on hills, ACC may not detect a vehicle in system functionality.
Page 432 430 STARTING AND OPERATING Lane Changing ACC may not detect a vehicle until it is completely in the lane in which you are traveling. In the illustration shown, ACC has not yet detected the vehicle changing lanes and it may not detect the vehicle until it’s too late for the ACC system to take action.
Page 433 STARTING AND OPERATING 431 Narrow Vehicles Stationary Objects And Vehicles Some narrow vehicles traveling near the outer edges of ACC does not react to stationary objects and stationary the lane or edging into the lane are not detected until they vehicles.
Page 434: General Information
432 STARTING AND OPERATING General Information Normal (Fixed Speed) Electronic Speed Control Mode This vehicle has systems that operate on radio frequency that comply with Part 15 of the Federal Communications In addition to Adaptive Cruise Control mode, a Normal Commission (FCC) rules and with Industry Canada (Fixed Speed) Electronic Speed Control mode is available Standards RSS- GEN/210/220/310.
Page 435 STARTING AND OPERATING 433 SET (-) button and release. Release the accelerator and the WARNING! vehicle will operate at the selected speed. Once a speed has been set a message (CRUISE CONTROL SET TO In the normal Cruise Control mode, the system will MPH/KM) will appear indicating what speed was set.
Page 436 434 STARTING AND OPERATING • If the button is continually pushed, the set speed will The drivers preferred units can be selected through the Uconnect Settings if equipped. Refer to “Uconnect Set- continue to increase in 10 km/h increments until the tings”...
Page 437 STARTING AND OPERATING 435 • If the button is continually pushed, the set speed will • The brake pedal is applied. continue to decrease in 5 mph decrements until the • The CANCEL button is pushed. button is released. The decrease in set speed is re- •...
Page 438: Parksense Rear Park Assist - If Equipped
436 STARTING AND OPERATING To Turn Off be automatically applied and released when performing a reverse parking maneuver if the system detects a The system will turn off and erase the set speed in possible collision with an obstacle. memory if: NOTE: •...
Page 439 STARTING AND OPERATING 437 • The automatic braking function may not be applied • The system is provided to assist the driver and not to fast enough for moving obstacles that approach the substitute the driver. rear of the vehicle from the left and / or right sides. •...
Page 440: Parksense Sensors
438 STARTING AND OPERATING Display (DID) indicating the vehicle speed is too fast. The The ParkSense Warning screen is located within the system will become active again if the vehicle speed is EVIC/DID. It provides visual warnings to indicate the decreased to speeds less than approximately 6 mph distance between the rear fascia/bumper and the de- (9 km/h).
Page 441 STARTING AND OPERATING 439 If an obstacle is detected in the left and/or right rear region, the display will show a single flashing arc in the left and/or right rear region and will produce a fast sound tone. As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the tone will change from fast to continuous.
Page 442 440 STARTING AND OPERATING Slow Tone/Solid Arc Fast Tone/Flashing Arc...
Page 443 STARTING AND OPERATING 441 Fast Tone/Flashing Arc Continuous Tone/Flashing Arc The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle:...
Page 444 442 STARTING AND OPERATING WARNING ALERTS Rear Greater than 79-59 in 59-47 in 47-39 in 39-25 in 25-12 in Less than Distance 79 in (200-150 cm) (150-120 cm) (120-100 cm) (100-65 cm) (65-30 cm) 12 in (in/cm) (200 cm) (30 cm) Arcs —...
Page 445: Enabling And Disabling Parksense
STARTING AND OPERATING 443 NOTE: ParkSense will reduce the volume of the radio, if on, when the system is sounding an audio tone. Enabling And Disabling ParkSense ParkSense can be enabled and disabled with the ParkSense switch, located on the switch panel below the Uconnect display.
Page 446: Service The Parksense Rear Park Assist System
444 STARTING AND OPERATING disabled, the EVIC/DID will display the “PARKSENSE UNAVAILABLE WIPE REAR SENSORS” or the OFF” message for as long as the vehicle is in REVERSE. “PARKSENSE UNAVAILABLE SERVICE REQUIRED” message. Refer to “Display” in “Getting To Know Your The ParkSense switch LED will be ON when ParkSense is Instrument Panel””...
Page 447: Cleaning The Parksense System
STARTING AND OPERATING 445 • When you turn ParkSense OFF, the instrument cluster If “PARKSENSE UNAVAILABLE SERVICE REQUIRED” appears in the EVIC/DID, see an authorized dealer. will display “PARKSENSE OFF” Furthermore, once you turn ParkSense off, it remains off until you turn it Cleaning The ParkSense System on again, even if you cycle the ignition.
Page 448 446 STARTING AND OPERATING • ParkSense should be disabled when the liftgate is in CAUTION! (Continued) the open position. • The vehicle must be driven slowly when using • Use the ParkSense switch to turn the ParkSense system ParkSense in order to be able to stop in time when OFF if objects such as bicycle carriers, trailer hitches, an obstacle is detected.
Page 449: Parksense Front And Rear Park Assist - If Equipped
STARTING AND OPERATING 447 up or moving forward, e.g. during a parking maneuver. WARNING! (Continued) If your vehicle is equipped with an Automatic Transmis- • Before using ParkSense, it is strongly recom- sion, the vehicle brakes may be automatically applied mended that the ball mount and hitch ball assem- and released when performing a reverse parking maneu- bly is disconnected from the vehicle when the...
Page 450 448 STARTING AND OPERATING • The automatic braking function may not provide NOTE: enough vehicle deceleration to avoid colliding with a • The driver is always responsible for controlling the detected obstacle depending on vehicle speed, road vehicle. conditions, and brake capability. •...
Page 451: Parksense Sensors
STARTING AND OPERATING 449 active until the vehicle speed is increased to approxi- NOTE: If your vehicle is equipped with the ParkSense mately 7 mph (11 km/h) or above. When in REVERSE Active Park Assist system, six sensors will be located in and above the system’s operating speed, a warning will the rear fascia/bumper.
Page 452: Parksense Display
450 STARTING AND OPERATING The ParkSense Warning screen is located within the If an obstacle is detected in the center rear region, the Electronic Vehicle Information Center (EVIC) or Driver display will show a single solid arc in the center rear Information Display (DID).
Page 453 STARTING AND OPERATING 451 Single 1/2 Second Tone/Solid Arc Slow Tone/Solid Arc...
Page 454 452 STARTING AND OPERATING Slow Tone/Solid Arc Fast Tone/Flashing Arc...
Page 455 STARTING AND OPERATING 453 Fast Tone/Flashing Arc Continuous Tone/Flashing Arc The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle:...
Page 456 454 STARTING AND OPERATING WARNING ALERTS Rear Greater than 79-59 in 59-47 in 47-39 in 39-25 in 25-12 in Less than Distance 79 in (200-150 cm) (150-120 cm) (120-100 cm) (100-65 cm) (65-30 cm) 12 in (in/cm) (200 cm) (30 cm) Arcs —...
Page 457 STARTING AND OPERATING 455 NOTE: ParkSense will reduce the volume of the radio, if left and/or right front region and will produce a fast on, when the system is sounding an audio tone. sound tone. As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the Front Park Assist vehicle and the tone will change from fast to continuous.
Page 458 456 STARTING AND OPERATING No Tone/Flashing Arc Fast Tone/Flashing Arc...
Page 459 STARTING AND OPERATING 457 The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: Continuous Tone/Flashing Arc...
Page 460 458 STARTING AND OPERATING WARNING ALERTS Front Distance Greater than 47-39 in 39-25 in 25-12 in Less than (in/cm) 47 in (120 cm) (120-100 cm) (100-65 cm) (65-30 cm) 12 in (30 cm) Arcs — Left None None None 2nd Flashing 1st Flashing Arcs —...
Page 461: Enabling And Disabling Parksense
STARTING AND OPERATING 459 The chime volume settings include LOW, MEDIUM, and HIGH. The factory default volume setting is MEDIUM. ParkSense will retain its last known configuration state through ignition cycles. Enabling And Disabling ParkSense ParkSense can be enabled and disabled with the ParkSense switch, located on the switch panel below the Uconnect display.
Page 462: Service The Parksense Park Assist System
460 STARTING AND OPERATING disabled, the EVIC/DID will display the “PARKSENSE SENSORS , PARKSENSE UNAVAILABLE WIPE OFF” message for as long as the vehicle is in REVERSE. FRONT SENSORS , or the PARKSENSE UNAVAIL- ABLE SERVICE REQUIRED message for five seconds. The ParkSense switch LED will be ON when ParkSense is When the gear selector is moved to Reverse and the disabled or requires service.
Page 463: Cleaning The Parksense System
STARTING AND OPERATING 461 second pop-up duration. The car graphic will remain Cleaning The ParkSense System displayed for as long as the vehicle is in REVERSE. Refer Clean the ParkSense sensors with water, car wash soap to “Display” in “Getting To Know Your Instrument and a soft cloth.
Page 464 462 STARTING AND OPERATING • When you move the gear selector to the REVERSE bumper. Failure to do so can result in the system position and ParkSense is turned off, the instrument misinterpreting a close object as a sensor problem, cluster will display “PARKSENSE OFF”...
Page 465 STARTING AND OPERATING 463 CAUTION! (Continued) WARNING! (Continued) the sensors will not be detected when they are in pay attention to your surroundings. Failure to do so close proximity. can result in serious injury or death. • The vehicle must be driven slowly when using •...
Page 466: Parksense Active Park Assist System - If Equipped
464 STARTING AND OPERATING • The system is provided to assist the driver and not to PARKSENSE ACTIVE PARK ASSIST SYSTEM — IF EQUIPPED substitute the driver. • During a semi-automatic maneuver, if the driver The ParkSense Active Park Assist system is intended to assist the driver during parallel and perpendicular park- touches the steering wheel after being instructed to ing maneuvers by identifying a proper parking space,...
Page 467: Enabling And Disabling The Parksense Active Park Assist System
STARTING AND OPERATING 465 The system will also continuously perform the dy- namic vehicle calibration to account for differences such as over or under inflated tires and new tires. Enabling And Disabling The ParkSense Active Park Assist System The ParkSense Active Park Assist system can be enabled and disabled with the ParkSense Active Park Assist switch, located on the switch panel below the Uconnect display.
Page 468 466 STARTING AND OPERATING • The ParkSense Active Park Assist system will allow a The ParkSense Active Park Assist system will turn off automatically for any of the following conditions: maximum of six shifts between DRIVE and REVERSE. If the maneuver cannot be completed within six shifts, •...
Page 469: Parallel Parking Space Assistance Operation/Display
STARTING AND OPERATING 467 NOTE: If the vehicle is driven above approximately Parallel Parking Space Assistance Operation/ 15 mph (25 km/h), the DID will instruct the driver to Display slow down. If the vehicle is driven above approximately When the ParkSense Active Park Assist system is enabled 18 mph (30 km/h), the system will cancel.
Page 470 468 STARTING AND OPERATING • The driver needs to make sure that the selected parking space for the maneuver remains free and clear of any obstructions (e.g. pedestrians, bicycles, etc.). • The driver is responsible to ensure that the selected parking space is suitable for the maneuver and free/ clear of anything that may be overhanging or protrud- ing into the parking space (e.g., ladders, tailgates, etc.
Page 471 STARTING AND OPERATING 469 Parking Space Found — Keep Moving Forward Parking Space Found — Stop And Remove Hands From Wheel Once the vehicle is in position, you will be instructed to Once the vehicle is at a standstill with your hands stop the vehicle’s movement and remove your hands removed from the steering wheel, you will be instructed from the steering wheel.
Page 472 470 STARTING AND OPERATING Parking Space Found — Shift To Reverse Check Surroundings — Wait For Steering To Complete When the driver places the gear selector into the RE- The system will then instruct the driver to check their VERSE position, the system may instruct the driver to surroundings and move backward.
Page 473 STARTING AND OPERATING 471 • When the system instructs the driver to remove their hands from the steering wheel, the driver should check their surroundings and begin to back up slowly. • The ParkSense Active Park Assist system will allow a maximum of six shifts between DRIVE or REVERSE.
Page 474 472 STARTING AND OPERATING When the vehicle has reached the end of its backward NOTE: It is the driver’s responsibility to use the brake movement, the system will instruct the driver to check and stop the vehicle. The driver should check their their surroundings and stop the vehicle’s movement.
Page 475 STARTING AND OPERATING 473 Check Surroundings — Shift To Drive Check Surroundings — Wait For Steering To Complete When the driver places the gear selector into the DRIVE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move forward.
Page 476 474 STARTING AND OPERATING Check Surroundings — Move Forward Check Surroundings — STOP When the vehicle has reached the end of its forward NOTE: It is the driver’s responsibility to use the brake movement, the system will instruct the driver to check and stop the vehicle.
Page 477 STARTING AND OPERATING 475 Once the vehicle is in a standstill condition, the driver When the driver places the gear selector into the RE- will be instructed to place the gear selector into the VERSE position, the system may instruct the driver to REVERSE position.
Page 478 476 STARTING AND OPERATING The system will then instruct the driver to check their check the vehicle’s parking position. If the driver is surroundings and move backward. satisfied with the vehicle position, they should shift to PARK. The Active ParkSense Complete - Check Parking Position message will be momentarily displayed.
Page 479: Perpendicular Parking Space Assistance Operation/Display
STARTING AND OPERATING 477 Perpendicular Parking Space Assistance Operation/Display When the ParkSense Active Park Assist system is en- abled, the “Active ParkSense Searching - Press OK for Perpendicular Park” message will show in the DID display. Push the OK button on the left side steering wheel switch to change your parking space setting to a perpendicular maneuver.
Page 480 478 STARTING AND OPERATING • When seeking for a parking space, the driver should NOTE: drive as parallel or perpendicular (depending on the • When searching for a parking space, use the turn type of maneuver) to other vehicles as possible. signal indicator to select which side of the vehicle you •...
Page 481 STARTING AND OPERATING 479 Parking Space Found — Keep Moving Forward Parking Space Found — Stop And Remove Hands From Wheel Once the vehicle is in position, you will be instructed to Once the vehicle is at a standstill with your hands stop the vehicle’s movement and remove your hands removed from the steering wheel, you will be instructed from the steering wheel.
Page 482 480 STARTING AND OPERATING Parking Space Found — Shift To Reverse Check Surroundings — Wait For Steering To Complete When the driver places the gear selector into the RE- The system will then instruct the driver to check their VERSE position, the system may instruct the driver to surroundings and move backward.
Page 483 STARTING AND OPERATING 481 • When the system instructs the driver to remove their hands from the steering wheel, the driver should check their surroundings and begin to back up slowly. • The ParkSense Active Park Assist system will allow a maximum of six shifts between DRIVE or REVERSE.
Page 484 482 STARTING AND OPERATING When the vehicle has reached the end of its backward NOTE: It is the driver’s responsibility to use the brake movement, the system will instruct the driver to check and stop the vehicle. The driver should check their their surroundings and stop the vehicle’s movement.
Page 485 STARTING AND OPERATING 483 Check Surroundings — Shift To Drive Check Surroundings — Wait For Steering To Complete When the driver places the gear selector into the DRIVE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move forward.
Page 486 484 STARTING AND OPERATING Check Surroundings — Move Forward Check Surroundings — STOP When the vehicle has reached the end of its forward NOTE: It is the driver’s responsibility to use the brake movement, the system will instruct the driver to check and stop the vehicle.
Page 487 STARTING AND OPERATING 485 Once the vehicle is in a standstill condition, the driver will be instructed to place the gear selector into the REVERSE position. Check Surroundings — Wait For Steering To Complete The system will then instruct the driver to check their surroundings and move backward.
Page 488 486 STARTING AND OPERATING Check Surroundings — Move Backwards Active ParkSense Complete — Check Parking Position Your vehicle is now in the perpendicular park position. When the maneuver is complete, the driver will be in- structed to check the vehicle’s parking position. If the driver is satisfied with the vehicle position, they should shift to PARK.
Page 489: Lanesense - If Equipped
STARTING AND OPERATING 487 CAUTION! WARNING! • The ParkSense Active Park Assist system is only a Drivers must be careful when performing parallel or parking aid and it is unable to recognize every perpendicular parking maneuvers even when using obstacle, including small obstacles. Parking curbs the ParkSense Active Park Assist system.
Page 490 488 STARTING AND OPERATING uses a forward looking camera to detect lane markings turn signal applied), the LaneSense system provides a and measure vehicle position within the lane boundaries. visual warning through the DID to prompt the driver to remain within the lane. When only a single lane marking When both lane markings are detected and the driver is detected, a haptic (torque) warning will not be pro- unintentionally drifts out of the lane (no turn signal...
Page 491: Turning Lanesense On Or Off
STARTING AND OPERATING 489 Turning LaneSense ON Or OFF To turn the LaneSense system ON, push the LaneSense button to turn the system ON (LED turns off). A “Lane The default status of LaneSense is “OFF”. Sense On” message is shown in the DID. The LaneSense button is located on the switch panel below the Uconnect display.
Page 492: Lanesense Warning Message
490 STARTING AND OPERATING NOTE: The LaneSense system will retain the last system state ON or OFF from the last ignition cycle when the ignition is changed to the ON/RUN position. LaneSense Warning Message The LaneSense system will indicate the current lane drift condition through the Driver Information Display (DID).
Page 493 STARTING AND OPERATING 491 • When the LaneSense system senses the lane has been NOTE: The LaneSense system operates with the similar approached and is in a lane departure situation, the behavior for a right lane departure when only the right left thick lane line flashes yellow (on/off), the left thin lane marking has been detected.
Page 494 492 STARTING AND OPERATING • For example: If approaching the left side of the lane the steering wheel will turn to the right. Lanes Sensed (White Lines/Green Indicator) • When the LaneSense system senses a lane drift situa- tion, the left thick lane line and left thin line turn solid Lane Sensed (Solid Yellow Thick Line, Solid Yellow Thin Line/Solid Yellow Indicator) yellow.
Page 495 STARTING AND OPERATING 493 • When the LaneSense system senses the lane has been approached and is in a lane departure situation, the left thick lane line flashes yellow (on/off) and the left thin line remains solid yellow. The LaneSense indicator changes from solid yellow to flashing yellow.
Page 496: Changing Lanesense Status
494 STARTING AND OPERATING Changing LaneSense Status PARKVIEW REAR BACK UP CAMERA — IF EQUIPPED The LaneSense system has settings to adjust the intensity of the torque warning and the warning zone sensitivity Your vehicle may be equipped with the ParkView Rear (Early/Medium/Late) that you can configure through Back Up Camera that allows you to see an on-screen the Uconnect system screen.
Page 497 STARTING AND OPERATING 495 displayed for up to 10 seconds after shifting out of REVERSE unless the vehicle speed exceeds 8 mph (13 km/h), the vehicle is shifted into PARK or the ignition is switched to the OFF position. A touch screen button to disable display of the camera image is made available when the vehicle is not in REVERSE gear.
Page 498 496 STARTING AND OPERATING The following table shows the approximate distances for each zone: Zone Distance to the rear of the vehicle 0 - 1 ft (0 - 30 cm) Yellow 1 ft - 6.5 ft (30 cm - 2 m) Green 6.5 ft or greater (2 m or greater) NOTE: If snow, ice, mud, or any foreign substance...
Page 499: Surround View Camera System - If Equipped
STARTING AND OPERATING 497 view is selected through the on screen soft buttons . The WARNING! top view of the vehicle will show which doors are open. The image will be displayed on the touchscreen display Drivers must be careful when backing up even when along with a caution note;...
Page 500 498 STARTING AND OPERATING REVERSE unless the vehicle speed exceeds 8 mph When enabled, active guide lines are overlaid on the (13 km/h), the vehicle is shifted into PARK or the ignition image to illustrate the width of the vehicle, including the is switched to the OFF position.
Page 501 STARTING AND OPERATING 499 Modes of Operation Additional camera modes can be selected when the vehicle is in any gear and the surround view camera system is activated by pressing the soft key located in the “Controls” screen or the “Apps” screen in the Uconnect system.
Page 502 500 STARTING AND OPERATING • Open Front doors will remove outside image. Front View Rear View The Front view will show you what is immediately in front of the vehicle and This is the Default view of the system is always paired with the Top view of in REVERSE and is always paired with the vehicle.
Page 503 STARTING AND OPERATING 501 • If a malfunction with the system has occurred, see Deactivation your nearest authorized dealer. The system can be deactivated in the following condi- tions: CAUTION! • The speed of the vehicle reaches greater than 8 mph •...
Page 504: Refueling The Vehicle
502 STARTING AND OPERATING WARNING! WARNING! • Never have any smoking materials lit in or near the Drivers must be careful when backing up even when using the Surround View Camera. Always check vehicle when the gas cap is removed or the tank is carefully behind your vehicle, and be sure to check being filled.
Page 505 STARTING AND OPERATING 503 CAUTION! (Continued) into the fuel system. Also, a poorly fitting aftermar- ket cap can cause the “Malfunction Indicator Light (MIL)” to illuminate, due to fuel vapors escaping from the system. • A poorly fitting fuel filler cap may cause the MIL to turn on.
Page 506: Vehicle Loading
504 STARTING AND OPERATING 5. After you have stopped pumping fuel, remove the fuel This label contains the month and year of manufacture, filler nozzle. Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR) front and rear, and Vehicle Identification 6.
Page 507 STARTING AND OPERATING 505 Gross Axle Weight Rating (GAWR) Inflation Pressure The GAWR is the maximum permissible load on the front This is the cold tire inflation pressure for your vehicle for and rear axles. The load must be distributed in the cargo all loading conditions up to full GAWR.
Page 508: Trailer Towing
506 STARTING AND OPERATING The weight on the front and rear of the vehicle should CAUTION! (Continued) then be determined separately to be sure that the load is parts on your vehicle can break, or it can change the properly distributed over the front and rear axle. Weigh- way your vehicle handles.
Page 509: Common Towing Definitions
STARTING AND OPERATING 507 Common Towing Definitions The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight The following trailer towing related definitions will assist of the trailer must be supported by the scale. you in understanding the following information: Gross Axle Weight Rating (GAWR) Gross Vehicle Weight Rating (GVWR)
Page 510 508 STARTING AND OPERATING Tongue Weight (TW) If equipped, the electronic Trailer Sway Control (TSC) recognizes a swaying trailer and automatically applies The tongue weight is the downward force exerted on the individual wheel brakes and/or reduces engine power to hitch ball by the trailer.
Page 511 STARTING AND OPERATING 509 Weight-Distributing Hitch WARNING! A weight-distributing system works by applying lever- • An improperly adjusted Weight Distributing Hitch age through spring (load) bars. They are typically used system may reduce handling, stability, braking for heavier loads to distribute trailer tongue weight to the performance, and could result in a collision.
Page 512: Trailer Hitch Classification
510 STARTING AND OPERATING Trailer Hitch Classification tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can Trailer Hitch Classification Definitions Class Max.
Page 513: Trailer Towing Weights (Maximum Trailer Weight Ratings)
STARTING AND OPERATING 511 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. GCWR (Gross Max. GTW Engine/ Trailer Tow Max. Tongue Combined Frontal Area (Gross Trailer Transmission Package Weight Weight Rating)
Page 514: Vehicle Loading Chart
512 STARTING AND OPERATING Vehicle Loading Chart EXAMPLE: • GVWR = 6005 lbs (2723 kg) Follow these steps to determine the total weight the vehicle can carry. • CURB = 4500 lbs (2041 kg) 1. Determine the cargo capacity of your vehicle. •...
Page 515 STARTING AND OPERATING 513 Number Of Persons / Weight Of Occupants Max Cargo No Tongue Load, Max Cargo Trailer Max Trailer With Max Trailer 360 lb (136 kg) Tongue Load 1205 lbs (546 kg) – 360 lbs (136 kg) 1205 lbs (546 kg) = 845 lbs 845 lbs (383 kg) 2 People / 300 lbs (136) kg...
Page 516: Trailer And Tongue Weight
514 STARTING AND OPERATING • Make sure loading does not exceed GAWR of front or Consider the following items when computing the rear axles. weight on the rear axle of the vehicle: • The tongue weight of the trailer. • GAWR are found on sticker in Drier Side Door Jam. •...
Page 517: Towing Requirements
STARTING AND OPERATING 515 Towing Requirements And Caring For Your Vehicle” for the proper mainte- nance intervals. When towing a trailer, never exceed the To promote proper break-in of your new vehicle drive- GAWR or GCWR ratings. train components, the following guidelines are recom- mended.
Page 518 516 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Total weight must be distributed between the tow cause a loss of control, poor performance or dam- age to brakes, axle, engine, transmission, steering, vehicle and the trailer such that the following four suspension, chassis structure or tires.
Page 519 STARTING AND OPERATING 517 • Proper tire inflation pressures are essential to the safe Towing Requirements — Trailer Brakes and satisfactory operation of your vehicle. Refer to • Do not interconnect the hydraulic brake system or “Tires” in “Maintaining And Caring For Your Vehicle” vacuum system of your vehicle with that of the trailer.
Page 520 518 STARTING AND OPERATING WARNING! CAUTION! (Continued) could lead to accelerated brake lining wear, higher • Do not connect trailer brakes to your vehicle’s brake pedal effort, and longer stopping distances. hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have Towing Requirements —...
Page 521 STARTING AND OPERATING 519 Four-Pin Connector Seven-Pin Connector 1 — Female Pins 4 — Park 1 — Battery 5 — Ground 2 — Male Pin 5 — Left Stop/Turn 2 — Backup Lamps 6 — Left Stop/Turn 3 — Ground 6 —...
Page 522: Towing Tips
520 STARTING AND OPERATING Towing Tips Cooling System Before setting out on a trip, practice turning, stopping, To reduce potential for engine and transmission over- and backing up the trailer in an area located away from heating, take the following actions: heavy traffic.
Page 523: Recreational Towing
STARTING AND OPERATING 521 RECREATIONAL TOWING Towing This Vehicle Behind Another Vehicle Towing Condition Wheel OFF the Ground All Models Flat Tow NONE NOT ALLOWED Dolly Tow Front Rear NOT ALLOWED On Trailer • When towing your vehicle, always follow applicable NOTE: state and provincial laws.
Page 524: Recreational Towing - All Models
522 STARTING AND OPERATING Recreational Towing — All Models 7. Turn the ignition to the ON/RUN position, but do not start the engine. DO NOT flat tow this vehicle. Damage to the drivetrain will result. 8. Press and hold the brake pedal. Recreational towing is allowed ONLY if the front wheels 9.
Page 525: Driving Tips
STARTING AND OPERATING 523 CAUTION! (Continued) WARNING! • Towing this vehicle in violation of the above re- Rapid acceleration on slippery surfaces is dangerous. quirements can cause severe transmission damage. Unequal traction can cause sudden pulling of the Damage from improper towing is not covered un- front wheels.
Page 526: Driving Through Water
524 STARTING AND OPERATING 2. Slow down if the road has standing water or puddles. Flowing/Rising Water 3. Replace the tires when tread wear indicators first WARNING! become visible. Do not drive on or across a road or path where water 4.
Page 527 STARTING AND OPERATING 525 Shallow Standing Water CAUTION! Although your vehicle is capable of driving through • Always check the depth of the standing water shallow standing water, consider the following Cautions before driving through it. Never drive through and Warnings before doing so. standing water that is deeper than the bottom of the tire rims mounted on the vehicle.
Page 528 526 STARTING AND OPERATING CAUTION! (Continued) operate the vehicle if any fluid appears contami- nated, as this may result in further damage. Such damage is not covered by the New Vehicle Limited Warranty. • Getting water inside your vehicle’s engine can cause it to lock up and stall out, and cause serious internal damage to the engine.
Page 529 IN CASE OF EMERGENCY CONTENTS ▫ Interior Fuses ......558 HAZARD WARNING FLASHERS ...529 ASSIST AND 9–1–1 REARVIEW MIRROR —...
Page 530 528 IN CASE OF EMERGENCY ▫ Road Tire Installation ....579 MANUAL PARK RELEASE ....601 ▫...
Page 531: Hazard Warning Flashers
IN CASE OF EMERGENCY 529 HAZARD WARNING FLASHERS ASSIST AND 9–1–1 REARVIEW MIRROR — IF EQUIPPED The Hazard Warning flasher switch is located in the lower center area of the instrument panel. A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- Push the switch to turn on the Hazard Warning shield.
Page 532 530 IN CASE OF EMERGENCY WARNING! ALWAYS obey traffic laws and pay attention to the road. Some Uconnect Access services, including 9-1-1 and Assist, will NOT work without an operable 1X (voice/data) or 3G (data) network connection. NOTE: • Your vehicle may be transmitting data as authorized by the subscriber.
Page 533 IN CASE OF EMERGENCY 531 ASSIST Call 9-1-1 Call The ASSIST Button is used to automatically connect you 1. Push the 9-1-1 Call button on the Rearview Mirror. to any one of the following support centers: NOTE: In case the 9-1-1 Call button is pushed in error, •...
Page 534 532 IN CASE OF EMERGENCY 3. Once a connection between the vehicle and a 9-1-1 NOTE: operator is made, the 9-1-1 Call system may transmit • Your vehicle may be transmitting data as authorized the following important vehicle information to a 9-1-1 by the subscriber.
Page 535 IN CASE OF EMERGENCY 533 WARNING! WARNING! (Continued) electrical equipment to the vehicle’s electrical sys- • If anyone in the vehicle could be in danger (e.g., tem. This may prevent your vehicle from sending a fire or smoke is visible, dangerous road conditions signal to initiate an emergency call.
Page 536 534 IN CASE OF EMERGENCY 9-1-1 Call System Limitations WARNING! Vehicles sold in Canada and Mexico DO NOT have 9-1-1 • Ignoring the Rearview Mirror light could mean you Call system capabilities. will not have 9-1-1 Call services. If the Rearview 9-1-1 or other emergency line operators in Canada and Mirror light is illuminated, have an authorized Mexico may not answer or respond to 9-1-1 system calls.
Page 537 IN CASE OF EMERGENCY 535 • The vehicle’s electrical systems are not intact. WARNING! • The 9-1-1 Call system software and/or hardware are ALWAYS obey traffic laws and pay attention to the damaged during a crash. road. Some Uconnect Access services, including 9-1-1 •...
Page 538 536 IN CASE OF EMERGENCY General Information CAUTION! This device complies with Part 15 of the FCC Rules. To avoid damage to the mirror during cleaning, never Operation is subject to the following two conditions: (1) spray any cleaning solution directly onto the mirror. This device may not cause harmful interference, and (2) Apply the solution onto a clean cloth and wipe the this device must accept any interference received, includ-...
Page 539: Bulb Replacement
IN CASE OF EMERGENCY 537 BULB REPLACEMENT Replacement Bulbs Interior Bulbs Lamps Bulb Number Center & Rear Dome Lamp LED (Serviced at Authorized Dealer) Center & Rear Reading Lamps LED (Serviced at Authorized Dealer) Front Door Courtesy Lamp LED (Serviced at Authorized Dealer) Front Header Reading Lamps –...
Page 540 538 IN CASE OF EMERGENCY Exterior Bulbs Lamps Bulb Number High Intensity Discharge Headlamp Low Beam - D3S High Beam - 9005LL Halogen Headlamp Reflector Low Beam - H11LL Projector Halogen Low Beam - 9005HL+ All High Beams - 9005LL Dedicated Daytime Running Lamp (If Equipped) LED (Serviced at Authorized Dealer) Front Turn Signal Lamp...
Page 541: Replacing Exterior Bulbs
IN CASE OF EMERGENCY 539 Lamps Bulb Number Rear Tail/Side Marker Lamp Rear Tail - Body Side - W21/5WLL (If Bulb Equipped); LED (Serviced at Authorized Dealer) Rear Tail - Liftgate - W5WLL (If Bulb Equipped); LED (Serviced at Authorized Dealer) Rear Side Marker: W3W Backup Lamp W21W...
Page 542 540 IN CASE OF EMERGENCY WARNING! (Continued) ON. It may cause serious electrical shock or electro- cution if not serviced properly. See your authorized dealer for service. Bi-Halogen Headlamps 1. Reach behind the headlamp housing to access the headlamp bulb cap. 2.
Page 543 IN CASE OF EMERGENCY 541 Headlamp Bulb Socket Headlamp Bulb 4. Disconnect the bulb from the electrical connector and CAUTION! then connect the replacement bulb. Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.
Page 544 542 IN CASE OF EMERGENCY 5. Install the bulb and connector assembly into the headlamp housing and rotate clockwise to lock it in place. 6. Install the headlamp bulb cap in the headlamp hous- ing and rotate clockwise to lock it in place. Front Turn Signal Lamp 1.
Page 545 IN CASE OF EMERGENCY 543 Front And Rear Side Marker Lamps 2. Firmly grasp the front side marker lamp socket and rotate 1/4 turn counterclockwise to remove it from the 1. Remove the three fasteners from the inner wheel liner lamp assembly.
Page 546 544 IN CASE OF EMERGENCY 4. Install front side marker lamp socket in lamp assembly and rotate 1/4 turn clockwise to lock into place. 5. Position the inner wheel liner in place and install the three fasteners. Front Fog Lamp — Halogen 1.
Page 547 IN CASE OF EMERGENCY 545 3. Back-up lamps/tail lamp (if bulb equipped) are now CAUTION! visible. Rotate socket(s) counter clockwise. Do not touch the new bulb with your fingers. Oil 4. Remove/replace bulb(s). contamination will severely shorten bulb life. If the 5.
Page 548: Fuses
546 IN CASE OF EMERGENCY 6. Reverse process to reinstall the lamp onto vehicle. WARNING! (Continued) Center High-Mounted Stop Lamp (CHMSL) replace a blown fuse with metal wires or any other material. Failure to use proper fuses may result in The center high-mounted stop lamp is an LED assembly.
Page 549: General Information
IN CASE OF EMERGENCY 547 General Information The fuses protect electrical systems against excessive current. When a device does not work you must check the electrical circuit inside the fuse for a break/melt. Also please be aware that when using power outlets for extended periods of time with the engine off may result in vehicle battery discharge.
Page 550: Fuse Location
548 IN CASE OF EMERGENCY Fuse Location The fuses are grouped into four controllers located in the engine compartment and under the instrument panel. Underhood Fuses The Power Distribution Center is located in the engine compartment near the battery. This center contains car- tridge fuses, mini-fuses, micro-fuses, circuit breakers and relays.
Page 551 IN CASE OF EMERGENCY 549 Cavity Cartridge Fuse Blade Fuse Description – – Not Used – – Not Used – 5 Amp Tan Battery Sensor (IBS) – – Not Used – 10 Amp Red 40 Amp Green – Power Locks –...
Page 552 550 IN CASE OF EMERGENCY Cavity Cartridge Fuse Blade Fuse Description – – Not Used – – Not used – 20 Amp Yellow RR Wiper F25B – 10 Amp Red LT RR Door/RT RR Re- lease Module/Active Grill Shutter/Power Mirror 40 Amp Green –...
Page 553 IN CASE OF EMERGENCY 551 Cavity Cartridge Fuse Blade Fuse Description 20 Amp Blue – 30 Amp Pink – Power Liftgate Module 25 Amp Clear – RR Door Node 25 Amp Clear – Sunroof Control Module – – Not Used 40 Amp Green –...
Page 554 552 IN CASE OF EMERGENCY Cavity Cartridge Fuse Blade Fuse Description 30 Amp Pink – Power Inverter 30 Amp Pink – Driver Door Module 30 Amp Pink – Passenger Door Module – – Not Used 25 Amp Clear – RR Sliding Door Module 25 Amp Clear –...
Page 555 IN CASE OF EMERGENCY 553 Cavity Cartridge Fuse Blade Fuse Description – 10 Amp Red Front and Rear HVAC Control Module/ESP/ – – Not Used – – Not Used 30 Amp Pink – 7 Way Connector Recep- tacle — If Equipped –...
Page 556 554 IN CASE OF EMERGENCY Cavity Cartridge Fuse Blade Fuse Description – 15 Amp Blue Instrument Panel Cluster (IPC) – 10 Amp Red In Vehicle Temperature Sensor/Humidity Sensor/ Drivers Assist System Module (DASM)/Park Assist (PAM) – If Equipped – – Not Used –...
Page 557 IN CASE OF EMERGENCY 555 Cavity Cartridge Fuse Blade Fuse Description – 5 Amp Tan Overhead Console / RR – 20 Amp Yellow Uconnect/DCSD/ Telematics – 10 Amp Red RR Entertainment Screen 1 And 2/ Media Screen 1 And 2/ 3rd Row Row USB Charge Only/ 2nd Row YSB Charge Only/ Sunroof/Rainsensor/...
Page 558 556 IN CASE OF EMERGENCY Cavity Cartridge Fuse Blade Fuse Description – – Not Used – – Not Used 20 Amp Blue – TT Park Lights — If Equipped 40 Amp Green – ESP Motor Pump – 20 Amp Yellow Cigar Lighter –...
Page 559 IN CASE OF EMERGENCY 557 Cavity Cartridge Fuse Blade Fuse Description – – Not Used – 10 Amp Red USB Charge Only Port – 10 Amp Red Occupant Restraint Con- troller (ORC) (Airbag) – 10 Amp Red Occupant Restraint Con- troller (ORC) (Airbag) –...
Page 560: Interior Fuses
558 IN CASE OF EMERGENCY Interior Fuses The interior fuse panel is located in the passenger compartment on the left side dash panel under the instrument panel. Cavity Blade Fuse Description 15 Amp Blue Low Beam Left 10 Amp Red Interior Lighting 10 Amp Red Intrusion Module / Siren...
Page 561: Jacking And Tire Changing - If Equipped
IN CASE OF EMERGENCY 559 Cavity Blade Fuse Description 5 Amp Tan Fog Lamp Front Left 5 Amp Tan Fog Lamp Front Right 10 Amp Red Low Beam Right JACKING AND TIRE CHANGING — IF EQUIPPED WARNING! (Continued) • Being under a jacked-up vehicle is dangerous. The WARNING! vehicle could slip off the jack and fall on you.
Page 562: Jack And Spare Tire Location
560 IN CASE OF EMERGENCY Jack And Spare Tire Location Equipment Removal The jacking tools, spare tire and portable air compressor 1. Remove the access panel to the jacking equipment. (if equipped) or tire service kit (if equipped)are stowed 2. Unlatch the Portable Air Compressor or Tire Service behind a access panel on left hand side of the vehicle.
Page 563 IN CASE OF EMERGENCY 561 3. Remove Jack by turning the jack screw counterclock- wise to collapse from storage area that is located behind the tire. Jacking Equipment 1 — Inflatable Spare Tire 2 — Tire Service Kit 3 — Wrench Jack Location 4 —...
Page 564: Preparations For Jacking
562 IN CASE OF EMERGENCY Preparations For Jacking 6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if chang- 1. Park the vehicle on a firm, level surface. Avoid ice or ing the right front tire, block the left rear wheel.
Page 565 IN CASE OF EMERGENCY 563 WARNING! (Continued) • Turn on the Hazard Warning flasher. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set the transmis- Jack Warning Label sion in PARK. •...
Page 566 564 IN CASE OF EMERGENCY Extending The Wrench Jack Locations 1. Loosen (but do not remove) the wheel lug nuts by CAUTION! turning them to the left one turn while the wheel is still on the ground. Do not attempt to raise the vehicle by jacking on locations other than those indicated.
Page 567 IN CASE OF EMERGENCY 565 Front Jack Location Front Jack Engaged...
Page 568 566 IN CASE OF EMERGENCY Rear Jacking Location Rear Jack Engaged WARNING! Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body (Continued)
Page 569 IN CASE OF EMERGENCY 567 WARNING! (Continued) WARNING! under a vehicle that is on a jack. If you need to get Raising the vehicle higher than necessary can make under a raised vehicle, take it to a service center the vehicle less stable. It could slip off the jack and where it can be raised on a lift.
Page 570 568 IN CASE OF EMERGENCY CAUTION! (Continued) WARNING! damaged if the inflatable spare tire is mounted To avoid the risk of forcing the vehicle off the jack, incorrectly. do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in serious injury.
Page 571 IN CASE OF EMERGENCY 569 equipped. Refer to “Tire Service Kit For Inflating Tire” 11. Lower the jack to its fully-closed position. in this section for usage procedure if equipped WARNING! 9. Lower the car once the inflatable Spare has reached its pressure and the compressor-hose has been removed A loose tire or jack thrown forward in a collision or from the tire valve.
Page 572 570 IN CASE OF EMERGENCY 12. Place the deflated (flat) tire and foam tray cover assembly in the rear cargo area. Do not stow the deflated tire in the inflatable spare tire location. Have the full-sized tire repaired or replaced, as soon as possible.
Page 573: Portable Air Compressor - If Equipped
IN CASE OF EMERGENCY 571 Portable Air Compressor — If Equipped Your vehicle may be equipped with a Portable Air Compressor. Use the Portable Air Compressor located in the side compartment of the cargo area to inflate the inflatable tire to 60 psi (4.2 Bar). Portable Air Compressor 1 —...
Page 574 572 IN CASE OF EMERGENCY Portable Air Compressor Usage With Inflatable Spare 3. Install the Inflatable Spare tire as Tire described in the Jack Instructions section in this manual. Make sure 1. Remove the Portable Air Compressor from the storage that the valve stem is located near location.
Page 575 IN CASE OF EMERGENCY 573 5. Always start the engine before 7. Inflate the tire to 60 psi (4.2 Bar) turning ON the Portable Air Com- recommended as per the label on pressor. the wheel or if the vehicle equipped with the inflatable spare tire pres- sure indicated on the Tire and Loading information label located...
Page 576: Tire Service Kit For Inflating Tire - If Equipped
574 IN CASE OF EMERGENCY 9. Remove the speed limit label WARNING! sticker from the Portable Air Com- • Do not lift or carry the Portable Air Compressor by pressor and place it on the center of the steering wheel. the hose.
Page 577 IN CASE OF EMERGENCY 575 Tire Service Kit And Components And Operation Using The Mode Select Knob And Hoses Your Tire Service Kit is equipped with the following symbols to indicate the air or sealant mode. Selecting Air Mode Push in the Mode Select Knob and turn to this position for air mode op- eration only.
Page 578 576 IN CASE OF EMERGENCY Using The Power Button WARNING! Push and release the Power Button • Keep Tire Service Kit away from open flames or once to turn On the Tire Service Kit. heat source. Push and release the Power Button •...
Page 579 IN CASE OF EMERGENCY 577 kit when running the air pump. Move the vehicle as WARNING! (Continued) necessary to place the valve stem in this position • Tire Service Kit Sealant solution contains latex. In before proceeding. case of an allergic reaction or rash, consult a phy- 3.
Page 580 578 IN CASE OF EMERGENCY 3. Uncoil the Power Plug and insert 7. Turn the Mode Select Knob to Air the plug into the vehicle’s 12 Volt Mode position. power outlet. 4. Place the Tire Service Kit on the ground next to the NOTE: Do not fill inflatable spare tire with sealant.
Page 581: Road Tire Installation
IN CASE OF EMERGENCY 579 9. Inflate the tire to 60 psi (4.2 Bar) 11. Remove the speed limit label recommended as per the label on sticker from the Tire Service Kit the wheel or if the vehicle equipped and place it on the center of the with the inflatable spare tire pres- steering wheel.
Page 582 580 IN CASE OF EMERGENCY the lug nuts with the cone shaped end of the nut 3. Align the valve notch in the wheel cover with the toward the wheel. Lightly tighten the lug nuts. valve stem on the wheel. Install the cover by hand, snapping the cover over the two lug nuts.
Page 583 IN CASE OF EMERGENCY 581 leverage. Tighten the lug nuts in a star pattern until WARNING! each nut has been tightened twice. Refer to “Torque Specifications” in the “Technical Data” section for To avoid the risk of forcing the vehicle off the jack, proper wheel lug nut torque.
Page 584: Return Inflatable Spare Tire
582 IN CASE OF EMERGENCY 5. After 25 miles (40 km) check the lug nut torque with a 6. Install the Tire Service Kit or Portable Air Compressor torque wrench to ensure that all lug nuts are properly if equipped and tighten the strap. seated against the wheel.
Page 585 IN CASE OF EMERGENCY 583 Tire Service Kit And Components And Operation Tire Service Kit Components 1 — Mode Select Knob Tire Service Kit Location 2 — Sealant/Air Hose 3 — Hose Accessories 4 — Sealant Bottle 5 — Power Plug 6 —...
Page 586 584 IN CASE OF EMERGENCY Using The Mode Select Knob And Hoses Using The Power Button Your Tire Service Kit is equipped with the following Push and release the Power Button symbols to indicate the air or sealant mode. once to turn On the Tire Service Kit. Push and release the Power Button Selecting Air Mode again to turn Off the Tire Service Kit.
Page 587 IN CASE OF EMERGENCY 585 • You can use the Tire Service Kit air pump to inflate on the bottle label) to assure optimum operation of the system. Refer to “Sealant Bottle Replacement” in this bicycle tires. The kit also comes with two needles, section.
Page 588 586 IN CASE OF EMERGENCY WARNING! (Continued) WARNING! (Continued) • Do not use Tire Service Kit or drive the vehicle of the vehicle. Always stow the Tire Service Kit in under the following circumstances: the place provided. Failure to follow these warn- ings can result in injuries that are serious or fatal to –...
Page 589 IN CASE OF EMERGENCY 587 running the air pump. Move the vehicle as necessary WARNING! (Continued) to place the valve stem in this position before proceed- reach of children. If swallowed, rinse mouth imme- ing. diately with plenty of water and drink plenty of 3.
Page 590 588 IN CASE OF EMERGENCY 3. Remove the cap from the valve Injecting Tire Service Kit Sealant Into The Deflated Tire: stem and then screw the fitting at 1. Always start the engine before the end of the Sealant Hose onto the turning ON the Tire Service Kit.
Page 591 IN CASE OF EMERGENCY 589 3. After pushing the Power Button, Make sure the valve stem is free of debris. Reconnect the sealant (white fluid) will flow the Sealant Hose to the valve stem. Check that the from the Sealant Bottle through the Mode Select Knob is in the Sealant Mode position and Sealant Hose and into the tire.
Page 592 590 IN CASE OF EMERGENCY If the sealant (white fluid) does flow through the 2. The pump will start to inject air into Sealant Hose: the tire immediately after the Seal- ant Bottle is empty. Continue to 1. Continue to operate the pump until operate the pump and inflate the sealant longer...
Page 593 IN CASE OF EMERGENCY 591 If the tire inflates to the recommended pressure or is at 2. Remove the speed limit label from least 26 psi (1.8 Bar) pressure within 15 minutes: the Tire Service Kit and place sticker on the steering wheel. NOTE: If the tire becomes over-inflated, push the Defla- tion Button to reduce the tire pressure to the recom- mended inflation pressure before continuing.
Page 594 592 IN CASE OF EMERGENCY Drive Vehicle: After Driving: Immediately after injecting sealant Pull over to a safe location. Refer to “Whenever You Stop and inflating the tire, drive the vehicle To Use Tire Service Kit” in this section before continuing. 5 miles (8 km) or 10 minutes to ensure 1.
Page 595 IN CASE OF EMERGENCY 593 4. Uncoil the power plug and insert 6. Turn the Mode Select Knob and the plug into the vehicle’s 12 Volt turn to the Air Mode position. power outlet. 5. Uncoil the Hose and screw the fit- 7.
Page 596 594 IN CASE OF EMERGENCY If the tire pressure is 19 psi (1.3 Bar) or higher: 4. Have the tire inspected and repaired or replaced at the earliest opportunity at an authorized dealer or tire 1. Push the Power Button to turn on service center.
Page 597: Jump-Starting
IN CASE OF EMERGENCY 595 4. Rotate the bottle up beyond vertical to release. NOTE: When using a portable battery booster pack follow the manufacturer’s operating instructions and 5. Pull the bottle away from the Compressor. precautions. NOTE: CAUTION! • For sealant bottle installation follow these steps re- verse order.
Page 598: Preparations For Jump-Start
596 IN CASE OF EMERGENCY Preparations For Jump-Start The battery in your vehicle is located on the left side of the engine compartment. Negative Remote Battery Post Positive Remote Battery Post...
Page 599: Jump-Starting Procedure
IN CASE OF EMERGENCY 597 3. If using another vehicle to jump-start the battery, park WARNING! the vehicle within the jumper cables reach, set the • Take care to avoid the radiator cooling fan when- parking brake and make sure the ignition is OFF. ever the hood is raised.
Page 600 598 IN CASE OF EMERGENCY 4. Connect the opposite end of the negative (-) jumper CAUTION! cable to the negative post near the windshield cowl (exposed metal part of the discharged vehicle’s engine). Failure to follow these procedures could result in damage to the charging system of the booster vehicle WARNING! or the discharged vehicle.
Page 601: Refuelling In Emergency
IN CASE OF EMERGENCY 599 6. Once the engine is started, remove the jumper cables CAUTION! in the reverse sequence: Accessories plugged into the vehicle power outlets Disconnecting The Jumper Cables draw power from the vehicle’s battery, even when not 1.
Page 602: If Your Engine Overheats
600 IN CASE OF EMERGENCY • You can also turn the temperature control to maximum For more information on the Cap-Less Fuel System refer to “Refuelling The Vehicle” in “Starting And Operating ” heat, the mode control to floor and the blower control in this manual.
Page 603: Manual Park Release
IN CASE OF EMERGENCY 601 MANUAL PARK RELEASE WARNING! WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If You should be seated in the driver’s seat with your you see or hear steam coming from under the hood, foot firmly placed on the brake pedal to maintain do not open the hood until the radiator has had time control of the vehicle before activating the Manual...
Page 604 602 IN CASE OF EMERGENCY In order to move the vehicle in cases where the transmis- 2. Apply the parking brake if possible. sion will not shift out of PARK (such as a dead battery), 3. Using a small screwdriver or similar tool, remove the a Manual Park Release is available.
Page 605: Freeing A Stuck Vehicle
IN CASE OF EMERGENCY 603 To Reset The Manual Park Release: NOTE: Shifts between DRIVE and REVERSE can only be achieved at wheel speeds of 5 mph (8 km/h) or less. 1. Pull the tether strap out again, then release it. Whenever the transmission remains in NEUTRAL for 2.
Page 606 604 IN CASE OF EMERGENCY CAUTION! WARNING! • Racing the engine or spinning the wheels may lead Fast spinning tires can be dangerous. Forces gener- to transmission overheating and failure. Allow the ated by excessive wheel speeds may cause damage, or engine to idle with the transmission in NEUTRAL even failure, of the axle and tires.
Page 607: Towing A Disabled Vehicle
IN CASE OF EMERGENCY 605 TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service. Towing Condition Wheel OFF the Ground ALL MODELS Flat Tow NONE NOT ALLOWED Wheel Lift Or Dolly Tow Front Rear NOT ALLOWED...
Page 608 606 IN CASE OF EMERGENCY • Vehicles with a discharged battery or total electrical CAUTION! failure when the electric parking brake (EPB) is en- gaged, will need a wheel dolly or jack to raise the rear Towing this vehicle in violation of the above require- wheels off the ground when moving the vehicle onto a ments can cause severe transmission damage.
Page 609 IN CASE OF EMERGENCY 607 • Use approved receptacle location to free the disabled CAUTION! vehicle from its environment. Recovery feature: • Is to be used by a professional ONLY. • Is used only to provide recovery of the vehicle. •...
Page 610: Enhanced Accident Response System (Ears)
608 IN CASE OF EMERGENCY NOTE: The Safehold feature will engage the Electric Park CAUTION! (Continued) Brake whenever the driver’s door is opened (if the • When securing the vehicle to a flatbed truck, do not ignition is ON, transmission is not in PARK, and brake attach to front or rear suspension components.
Page 611: Event Data Recorder (Edr)
IN CASE OF EMERGENCY 609 EVENT DATA RECORDER (EDR) This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per- formed.
Page 613 MAINTAINING AND CARING FOR YOUR VEHICLE CONTENTS ▫ Engine Air Cleaner Filter ....625 SCHEDULE SERVICING ....613 ▫...
Page 614 612 MAINTAINING AND CARING FOR YOUR VEHICLE ▫ Tire Safety Information ....639 STORING THE VEHICLE ....665 ▫...
Page 615: Schedule Servicing
MAINTAINING AND CARING FOR YOUR VEHICLE 613 SCHEDULE SERVICING than your authorized dealer, the message can be reset by referring to “Vehicle Info” in “Display” in “Getting To Your vehicle is equipped with an automatic oil change Know Your Instrument Panel”. indicator system.
Page 616 614 MAINTAINING AND CARING FOR YOUR VEHICLE • Check the fluid levels of the coolant reservoir and At Every Oil Change Interval As Indicated By Oil brake master cylinder, fill as needed. Change Indicator System: • Check function of all interior and exterior lights. •...
Page 617: Maintenance Plan
MAINTAINING AND CARING FOR YOUR VEHICLE 615 Maintenance Plan Mileage: Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, boot seals, tie rod ends, and replace if necessary. Inspect the brake linings, parking brake function. Inspect front accessory drive belt, tensioner, idler pulley, and replace if necessary Additional Maintenance Replace engine air cleaner filter.
Page 618 616 MAINTAINING AND CARING FOR YOUR VEHICLE Mileage: Or Years: Or Kilometers: Replace spark plugs ** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first. Inspect and replace PCV valve if necessary. ** The spark plug change interval is mileage based only, yearly intervals do not apply.
Page 619: Heavy Duty Use Of The Vehicle
MAINTAINING AND CARING FOR YOUR VEHICLE 617 Heavy Duty Use Of The Vehicle WARNING! Change Engine Oil at 4,000 miles (6,500 km) if the vehicle • You can be badly injured working on or around a is operated in a dusty and off road environment or is motor vehicle.
Page 620: Engine Compartment - 3.6L
618 MAINTAINING AND CARING FOR YOUR VEHICLE ENGINE COMPARTMENT — 3.6L 1 — Engine Coolant Pressure Cap 6 — Battery 2 — Engine Oil Fill 7 — Engine Oil Dipstick 3 — Brake Fluid Reservoir 8 — Window Washer Fill 4 —...
Page 621: Checking Oil Level
MAINTAINING AND CARING FOR YOUR VEHICLE 619 Checking Oil Level Adding Washer Fluid To assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed engine is shut OFF.
Page 622: Maintenance-Free Battery
620 MAINTAINING AND CARING FOR YOUR VEHICLE windshield washer solvent (not radiator antifreeze) and Maintenance-Free Battery operate the system for a few seconds to flush out the Your vehicle is equipped with a maintenance-free battery. residual washer fluid. You will never have to add water, nor is periodic main- When refilling the washer fluid reservoir, take some tenance required.
Page 623: Dealer Service
MAINTAINING AND CARING FOR YOUR VEHICLE 621 WARNING! (Continued) CAUTION! (Continued) • If a “fast charger” is used while the battery is in the an output greater than 12 Volts. Do not allow cable clamps to touch each other. vehicle, disconnect both vehicle battery cables be- •...
Page 624: Engine Oil
622 MAINTAINING AND CARING FOR YOUR VEHICLE NOTE: Under no circumstances should oil change inter- WARNING! vals exceed 10,000 miles (16,000 km), twelve months or 350 hours of engine run time, whichever comes first. The You can be badly injured working on or around a 350 hours of engine run or idle time is generally only a motor vehicle.
Page 625 MAINTAINING AND CARING FOR YOUR VEHICLE 623 American Petroleum Institute (API) Engine Oil Engine Oil Viscosity Identification Symbol MOPAR SAE 0W-20 engine oil approved to FCA Material Standard MS-6395 such as Pennzoil, Shell Helix or This symbol means that the oil has equivalent is recommended for all operating tempera- been certified by the American tures.
Page 626: Engine Oil Filter
624 MAINTAINING AND CARING FOR YOUR VEHICLE Synthetic Engine Oils indiscriminately discarded, can present a problem to the environment. Contact your authorized dealer, service You may use synthetic engine oils provided the recom- station or governmental agency for advice on how and mended oil quality requirements are met, and the recom- where used oil and oil filters can be safely discarded in mended maintenance intervals for oil and filter changes...
Page 627: Engine Air Cleaner Filter
MAINTAINING AND CARING FOR YOUR VEHICLE 625 Engine Air Cleaner Filter Engine Air Cleaner Filter Selection Refer to the “Scheduled Servicing” in this section for the The quality of replacement engine air cleaner filters proper maintenance intervals. varies considerably. Only high quality filters should be used to assure most efficient service.
Page 628 626 MAINTAINING AND CARING FOR YOUR VEHICLE WARNING! CAUTION! • Use only refrigerants and compressor lubricants Do not use chemical flushes in your air conditioning approved by the manufacturer for your air condi- system as the chemicals can damage your air condi- tioning system.
Page 629: Body Lubrication
MAINTAINING AND CARING FOR YOUR VEHICLE 627 Body Lubrication Windshield Wiper Blades Locks and all body pivot points, including such items as Clean the rubber edges of the wiper blades and the seat tracks, door hinge pivot points and rollers, liftgate, windshield periodically with a sponge or soft cloth and a tailgate, decklid, sliding doors and hood hinges, should mild nonabrasive cleaner.
Page 630: Exhaust System
628 MAINTAINING AND CARING FOR YOUR VEHICLE Exhaust System CAUTION! The best protection against carbon monoxide entry into • The catalytic converter requires the use of un- the vehicle body is a properly maintained engine exhaust leaded fuel only. Leaded gasoline will destroy the system.
Page 631 MAINTAINING AND CARING FOR YOUR VEHICLE 629 NOTE: Intentional tampering with emissions control WARNING! systems can result in civil penalties being assessed • Exhaust gases can injure or kill. They contain against you. carbon monoxide (CO), which is colorless and In unusual situations involving grossly malfunctioning odorless.
Page 632: Cooling System
630 MAINTAINING AND CARING FOR YOUR VEHICLE • Do not idle the engine with any spark plug wires system should be drained, flushed, and refilled with disconnected or removed, such as when diagnostic fresh OAT coolant (conforming to MS.90032) by an testing, or for prolonged periods during very rough authorized dealer.
Page 633 MAINTAINING AND CARING FOR YOUR VEHICLE 631 Cooling System — Drain, Flush And Refill CAUTION! NOTE: Some vehicles require special tools to add coolant • Mixing of engine coolant (antifreeze) other than properly. Failure to fill these systems properly could lead specified Organic Additive Technology (OAT) en- to severe internal engine damage.
Page 634 632 MAINTAINING AND CARING FOR YOUR VEHICLE Please review these recommendations for using Organic CAUTION! (Continued) Additive Technology (OAT) engine coolant (antifreeze) rust inhibitors or antirust products, as they may not that meets the requirements of FCA Material Standard be compatible with the radiator engine coolant and MS.90032.
Page 635 MAINTAINING AND CARING FOR YOUR VEHICLE 633 Please note that it is the owner’s responsibility to main- Cooling System Pressure Cap tain the proper level of protection against freezing ac- The cap must be fully tightened to prevent loss of engine cording to the temperatures occurring in the area where coolant (antifreeze), and to ensure that engine coolant the vehicle is operated.
Page 636 634 MAINTAINING AND CARING FOR YOUR VEHICLE Coolant Level WARNING! (Continued) The coolant expansion bottle provides a quick visual • Do not use a pressure cap other than the one method for determining that the coolant level is ad- specified for your vehicle. Personal injury or en- equate.
Page 637 MAINTAINING AND CARING FOR YOUR VEHICLE 635 • If frequent engine coolant (antifreeze) additions are Points To Remember required, the cooling system should be pressure tested NOTE: When the vehicle is stopped after a few miles/ for leaks. kilometers of operation, you may observe vapor coming •...
Page 638: Brake System
636 MAINTAINING AND CARING FOR YOUR VEHICLE result in unsatisfactory engine coolant (antifreeze) Brake Master Cylinder performance, poor gas mileage, and increased emis- The fluid in the master cylinder should be checked when sions. performing under hood services or immediately if the “Brake Warning Light”...
Page 639: Automatic Transmission
MAINTAINING AND CARING FOR YOUR VEHICLE 637 WARNING! WARNING! (Continued) • Overfilling the brake fluid reservoir can result in • Use only manufacturer’s recommended brake spilling brake fluid on hot engine parts, causing fluid. Refer to “Fluids And Lubricants” in “Tech- the brake fluid to catch fire.
Page 640 638 MAINTAINING AND CARING FOR YOUR VEHICLE fluid specifications. It is important to maintain the trans- its performance may be impaired by supplemental addi- mission fluid at the correct level using the recommended tives. Therefore, do not add any fluid additives to the fluid.
Page 641: Raising The Vehicle
MAINTAINING AND CARING FOR YOUR VEHICLE 639 tools. If you notice fluid leakage or transmission malfunc- Routine fluid and filter changes are not required. How- tion, visit your authorized dealer immediately to have ever, change the fluid and filter if the fluid becomes the transmission fluid level checked.
Page 642 640 MAINTAINING AND CARING FOR YOUR VEHICLE Tire Markings NOTE: • P (Passenger) — Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. •...
Page 643 MAINTAINING AND CARING FOR YOUR VEHICLE 641 • LT (Light Truck) — Metric tire sizing is based on U.S. Tire Identification Number (TIN) design standards. The size designation for LT-Metric The TIN may be found on one or both sides of the tire, tires is the same as for P-Metric tires except for the however, the date code may only be on one side.
Page 644 642 MAINTAINING AND CARING FOR YOUR VEHICLE EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation – This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards and is approved for highway use MA = Code representing the tire manufacturing location (two digits) L9 = Code representing the tire size (two digits) ABCD = Code used by the tire manufacturer (one to four digits)
Page 645 MAINTAINING AND CARING FOR YOUR VEHICLE 643 Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after Cold Tire Inflation Pressure the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three...
Page 646 644 MAINTAINING AND CARING FOR YOUR VEHICLE Tire Loading And Tire Pressure NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Example Tire Placard Location (B-Pillar) Example Tire Placard Location (Door)
Page 647 MAINTAINING AND CARING FOR YOUR VEHICLE 645 Tire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4.
Page 648 646 MAINTAINING AND CARING FOR YOUR VEHICLE NOTE: Under a maximum loaded vehicle condition, Steps For Determining Correct Load Limit gross axle weight ratings (GAWRs) for the front and rear 1. Locate the statement “The combined weight of occu- axles must not be exceeded. For further information on pants and cargo should never exceed XXX lbs or GAWRs, vehicle loading, and trailer towing, refer to XXX kg”...
Page 649 MAINTAINING AND CARING FOR YOUR VEHICLE 647 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • If your vehicle will be towing a trailer, load from your “XXX” amount equals 1,400 lbs (635 kg) and there will trailer will be transferred to your vehicle.
Page 650 648 MAINTAINING AND CARING FOR YOUR VEHICLE...
Page 651: Tires - General Information
MAINTAINING AND CARING FOR YOUR VEHICLE 649 Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions.
Page 652 650 MAINTAINING AND CARING FOR YOUR VEHICLE Fuel Economy WARNING! (Continued) Underinflated tires will increase tire rolling resistance • Unequal tire pressures from one side of the vehicle resulting in higher fuel consumption. to the other can cause the vehicle to drift to the right or left.
Page 653 MAINTAINING AND CARING FOR YOUR VEHICLE 651 At least once a month: 1 mile (1.6 km) after sitting for a minimum of three hours. The cold tire inflation pressure must not exceed the • Check and adjust tire pressure with a good quality maximum inflation pressure molded into the tire side- pocket-type pressure gauge.
Page 654 652 MAINTAINING AND CARING FOR YOUR VEHICLE Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) WARNING! during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. High speed driving with your vehicle under maxi- mum load is dangerous.
Page 655 MAINTAINING AND CARING FOR YOUR VEHICLE 653 Tire Repair Run Flat Tires — If Equipped Run Flat tires allow you the capability to drive 50 miles If your tire becomes damaged, it may be repaired if it (80 km) at 50 mph (80 km/h) after a rapid loss of inflation meets the following criteria: pressure.
Page 656 654 MAINTAINING AND CARING FOR YOUR VEHICLE Tire Spinning Tread Wear Indicators When stuck in mud, sand, snow, or ice conditions, do not Tread wear indicators are in the original equipment tires to help you in determining when your tires should be spin your vehicle’s wheels above 30 mph (48 km/h) or replaced.
Page 657 MAINTAINING AND CARING FOR YOUR VEHICLE 655 • Performance tires, tires with a speed rating of V or These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth higher, and Summer tires typically have a reduced becomes a 1/16 of an inch (1.6 mm).
Page 658 656 MAINTAINING AND CARING FOR YOUR VEHICLE wear and correct cold tire inflation pressures. The manu- It is recommended you contact your authorized tire facturer strongly recommends that you use tires equiva- dealer or original equipment dealer with any questions lent to the originals in size, quality and performance you may have on tire specifications or capability.
Page 659: Tire Types
MAINTAINING AND CARING FOR YOUR VEHICLE 657 Tire Types WARNING! (Continued) All Season Tires — If Equipped lose control and have a collision resulting in seri- ous injury or death. Use only the tire and wheel All Season tires provide traction for all seasons (Spring, sizes with load ratings approved for your vehicle.
Page 660 658 MAINTAINING AND CARING FOR YOUR VEHICLE Summer tires do not contain the all season designation or Snow Tires mountain/snowflake symbol on the tire sidewall. Use Some areas of the country require the use of snow tires Summer tires only in sets of four; failure to do so may during the Winter.
Page 661: Spare Tires - If Equipped
MAINTAINING AND CARING FOR YOUR VEHICLE 659 While studded tires improve performance on ice, skid Spare Tire Matching Original Equipped Tire And and traction capability on wet or dry surfaces may be Wheel — If Equipped poorer than that of non-studded tires. Some states pro- Your vehicle may be equipped with a spare tire and hibit studded tires;...
Page 662 660 MAINTAINING AND CARING FOR YOUR VEHICLE T, S = Temporary Spare Tire WARNING! (Continued) Since this tire has limited tread life, the original equip- replaced. Be sure to follow the warnings, which ment tire should be repaired (or replaced) and reinstalled apply to your spare.
Page 663: Tire Chains (Traction Devices)
MAINTAINING AND CARING FOR YOUR VEHICLE 661 Limited Use Spare — If Equipped WARNING! (Continued) The limited use spare tire is for temporary emergency use inflated to the cold tire inflation pressures listed on only. This tire is identified by a label located on the your Tire and Loading Information Placard located limited use spare wheel.
Page 664 662 MAINTAINING AND CARING FOR YOUR VEHICLE • For a 235/65R17 or 235/60R18 tire, use of a snow CAUTION! (Continued) traction device with a maximum projection of 9 mm damage. Stop the vehicle immediately if noise beyond the tire profile is recommended. occurs that could indicate device breakage.
Page 665: Tire Rotation Recommendations
MAINTAINING AND CARING FOR YOUR VEHICLE 663 Tire Rotation Recommendations The suggested rotation method is the “forward cross” shown in the following diagram. This rotation pattern The tires on the front and rear of your vehicle operate at does not apply to some directional tires that must not be different loads and perform different steering, driving, reversed.
Page 666: Department Of Transportation Uniform Tire Quality Grades
664 MAINTAINING AND CARING FOR YOUR VEHICLE DEPARTMENT OF TRANSPORTATION UNIFORM significantly from the norm due to variations in driving TIRE QUALITY GRADES habits, service practices, and differences in road charac- teristics and climate. The following tire grading categories were established by the National Highway Traffic Safety Administration.
Page 667: Temperature Grades
MAINTAINING AND CARING FOR YOUR VEHICLE 665 Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, The temperature grade for this tire is established for representing the tire’s resistance to the generation of heat a tire that is properly inflated and not overloaded. and its ability to dissipate heat, when tested under Excessive speed, under-inflation, or excessive load- controlled conditions on a specified indoor laboratory...
Page 668 666 MAINTAINING AND CARING FOR YOUR VEHICLE • If you do not disconnect the battery from the electrical • Do not drain the engine cooling system. system, check the battery charge every thirty days. • Whenever you leave the vehicle is stationary for two •...
Page 669: Bodywork
MAINTAINING AND CARING FOR YOUR VEHICLE 667 road surfaces on which the vehicle is operated, extreme CAUTION! hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- Before removal of the positive and negative termi- body protection.
Page 670: Body And Underbody Maintenance
668 MAINTAINING AND CARING FOR YOUR VEHICLE Body And Underbody Maintenance CAUTION! Wheel And Wheel Trim Care All wheels must have the same size and type tires. • All wheels and wheel trim, especially aluminum and Unequal tire sizes must not be used. Unequal tire chrome plated wheels, should be cleaned regularly size may cause failure of the power transfer unit.
Page 671: Preserving The Bodywork
MAINTAINING AND CARING FOR YOUR VEHICLE 669 Preserving The Bodywork CAUTION! Washing • Do not use abrasive or strong cleaning materials • Wash your vehicle regularly. Always wash your ve- such as steel wool or scouring powder that will hicle in the shade using MOPAR Car Wash, or a mild scratch metal and painted surfaces.
Page 672: Interiors
670 MAINTAINING AND CARING FOR YOUR VEHICLE • If you detect any stone chips or scratches in the paint, INTERIORS touch them up immediately. The cost of such repairs is Seats And Fabric Parts considered the responsibility of the owner. Use MOPAR Total Clean to clean fabric upholstery and •...
Page 673: Plastic And Coated Parts
MAINTAINING AND CARING FOR YOUR VEHICLE 671 Replace the belts if they appear frayed or worn or if the CAUTION! buckles do not work properly. Direct contact of air fresheners, insect repellents, WARNING! suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may A frayed or torn belt could rip apart in a collision and cause permanent damage.
Page 674: Leather Parts
672 MAINTAINING AND CARING FOR YOUR VEHICLE 1. Clean with a wet soft cloth. A mild soap solution may CAUTION! be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a Do not use Alcohol and Alcohol-based and/or Keton clean damp cloth.
Page 675 TECHNICAL DATA CONTENTS ▫ MMT In Gasoline .....680 IDENTIFICATION DATA ....675 ▫...
Page 676 674 TECHNICAL DATA ▫ Cruising Range ..... . .684 FLUIDS AND LUBRICANTS ....687 ▫...
Page 677: Identification Data
TECHNICAL DATA 675 IDENTIFICATION DATA Vehicle Identification Number The Vehicle Identification Number (VIN) is on the left front corner of the instrument panel and is visible from outside of the vehicle through the windshield. This number also appears stamped under the right front seat and printed on the Automobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title.
Page 678: Wheel And Tire Torque Specifications
676 TECHNICAL DATA WHEEL AND TIRE TORQUE SPECIFICATIONS Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Any time a wheel has been removed and reinstalled on the vehicle the lug nuts/bolts should be torqued using a properly calibrated torque wrench.
Page 679: Fuel Requirements
TECHNICAL DATA 677 WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. FUEL REQUIREMENTS These engines are designed to meet all emissions regulations and provide opti- mum fuel economy and performance...
Page 680: Reformulated Gasoline
678 TECHNICAL DATA While operating on gasoline with an octane number of The use of reformulated gasoline is recommended. Prop- 87, hearing a light knocking sound from the engine is not erly blended reformulated gasoline will provide im- a cause for concern. However, if the engine is heard proved performance and durability of engine and fuel making a heavy knocking sound, see your dealer imme- system components.
Page 681: Gasoline/Oxygenate Blends
TECHNICAL DATA 679 Detergent gasoline is recommended. Visit www.toptier- CAUTION! (Continued) gas.com for a list of TOP TIER Detergent Gasoline problems, damage critical fuel system components, Retailers. cause emissions to exceed the applicable standard, Indiscriminate use of fuel system cleaning agents should and/or cause the “Malfunction Indicator Light”...
Page 682: Mmt In Gasoline
680 TECHNICAL DATA CNG or LP are not the responsibility of the manufacturer Fuel System Cautions and may void or not be covered under the New Vehicle Limited Warranty. CAUTION! MMT In Gasoline Follow these guidelines to maintain your vehicle’s performance: Methylcyclopentadienyl Manganese Tricarbonyl (MMT) •...
Page 683: Carbon Monoxide Warnings
TECHNICAL DATA 681 Carbon Monoxide Warnings CAUTION! (Continued) • The use of fuel additives, which are now being WARNING! sold as octane enhancers, is not recommended. Carbon monoxide (CO) in exhaust gases is deadly. Most of these products contain high concentrations Follow the precautions below to prevent carbon of methanol.
Page 684: Flexible Fuel - If Equipped
682 TECHNICAL DATA WARNING! (Continued) WARNING! time the vehicle is raised. Have any abnormal Only vehicles with the E-85 fuel filler door label or a conditions repaired promptly. Until repaired, drive yellow gas cap can operate on E-85. with all side windows fully open. Ethanol Fuel (E-85) FLEXIBLE FUEL —...
Page 685: Fuel Requirements
TECHNICAL DATA 683 Fuel Requirements NOTE: • Use seasonally adjusted E-85 fuel (ASTM D5798). With If your vehicle is E-85 compatible, it will operate on unleaded gasoline with any octane rating, or solely E-85 non-seasonally adjusted E-85 fuel, hard starting and fuel, or any mixture of these fuels.
Page 686: Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles
684 TECHNICAL DATA Selection Of Engine Oil For Flexible Fuel Vehicles until the engine is fully warmed up. These issues may be (E-85) And Gasoline Vehicles improved with the use of seasonally adjusted E-85 fuel. FFV vehicles operated on E-85 require specially formu- NOTE: Use of the engine block heater (if equipped) may lated engine oils.
Page 687: Replacement Parts
TECHNICAL DATA 685 Replacement Parts Maintenance All fuel and engine components in your Flexible Fuel CAUTION! Vehicle (FFV) are designed to be compatible with ethanol. Ethanol compatible service components are required. Do not use ethanol mixture greater than 85% in your vehicle.
Page 688: Fluid Capacities
686 TECHNICAL DATA FLUID CAPACITIES U.S. Metric Fuel (Approximate) 3.6L Engines 19 Gallons 71 Liters Engine Oil With Filter 3.6 Liter Engine (SAE 0W-20 , API 5 quarts 4.7 liters Certified) Cooling System* 3.6 Liter Engine (MOPAR 13.1 Quarts — Standard Duty 12.4 Liters —...
Page 689: Fluids And Lubricants
TECHNICAL DATA 687 FLUIDS AND LUBRICANTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of FCA Material Standard MS.90032. Engine Oil – 3.6L Engine We recommend you use API Certified SAE 0W-20 Engine Oil, meeting the requirements of FCA Material Standard MS-6395 such as MOPAR, Pennzoil, and Shell Helix.
Page 690 688 TECHNICAL DATA CAUTION! CAUTION! (Continued) • Do not use water alone or alcohol-based engine • Mixing of engine coolant (antifreeze) other than coolant (antifreeze) products. Do not use additional specified Organic Additive Technology (OAT) en- rust inhibitors or antirust products, as they may not gine coolant (antifreeze), may result in engine be compatible with the radiator engine coolant and damage and may decrease corrosion protection.
Page 691: Chassis
TECHNICAL DATA 689 Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Use only MOPAR ZF 8&9 Speed ATF Automatic Trans- mission Fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Brake Master Cylinder We recommend you use MOPAR DOT 3 Brake Fluid, SAE J1703 should be used.
Page 693 MULTIMEDIA CONTENTS UCONNECT RADIOS ....694 AUX/USB/MP3 CONTROL ....743 PERSONALIZED MENU BAR .
Page 694 692 MULTIMEDIA ▫ Media Sources ......752 ▫ General Information....770 ▫...
Page 695 MULTIMEDIA ▫ Navigation ......784 ▫ SiriusXM Travel Link ....791 ▫...
Page 696: Uconnect Radios
694 MULTIMEDIA UCONNECT RADIOS For detailed information about your Uconnect radio, refer to your Uconnect Supplement Manual. PERSONALIZED MENU BAR The Uconnect features and services in the main menu bar are easily changed for your convenience. Simply follow these steps: Personalized Menu Bar 1.
Page 697: Cybersecurity
MULTIMEDIA CYBERSECURITY The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent Your vehicle may be a connected vehicle and may be version of vehicle software (such as Uconnect software) is equipped with both wired and wireless networks.
Page 698: Uconnect Settings
696 MULTIMEDIA Privacy of any wireless and wired communications can- WARNING! (Continued) not be assured. Third parties may unlawfully intercept may increase the possibility for vehicle systems to information and private communications without your be breached. consent. For further information, refer to “Privacy Prac- •...
Page 699: Customer Programmable Features - Uconnect
MULTIMEDIA Buttons on the faceplate are located below, and beside the Customer Programmable Features — Uconnect Uconnect system in the center of the instrument panel. In 5.0 Settings addition, there is a Scroll/Enter control knob located on the right side. Turn the control knob to scroll through menus and change settings (i.e., 30, 60, 90), push the center of the control knob one or more times to select or change a setting (i.e., ON, OFF).
Page 700 698 MULTIMEDIA Push the MORE button on the faceplate, then press KeySense the “Settings ” button on the touchscreen to display The vehicle’s KeySense settings are protected by a unique the settings menu screen. In this mode the Uconnect 4-digit PIN, which the vehicle owner creates when ac- system allows you to access all of the available pro- cessing the specific settings for the first time.
Page 701 MULTIMEDIA • Forward Collision Warning Active Braking • Front ParkSense Volume The FCW system includes Advanced Brake Assist (ABA). The chime volume settings include LOW, MEDIUM, and When this feature is selected, the ABA applies additional HIGH. The KeySense default volume setting is ME- brake pressure when the driver requests insufficient DIUM.
Page 702 700 MULTIMEDIA • Rear ParkSense Braking Assist exterior mirrors as well as an audible alert when the turn signal is on. The KeySense default is “Light & Chime”. When this feature is selected, the ParkSense system will Press the “Lights” or “Lights & Chime” button on the detect objects located behind the vehicle and utilize touchscreen to change the Blind Spot Alert status.
Page 703 MULTIMEDIA • SiriusXM Setup Write down the SIRIUS ID numbers for your receiver. To reactivate your service, either call the number listed on After pressing the “SiriusXM Setup” button on the touch- the screen or visit the provider online. screen, the following settings will be available: •...
Page 704 702 MULTIMEDIA • Brightness the “Touchscreen Beep” button on the touchscreen until a check-mark appears next to the setting, showing that When in this display, you may select the overall screen setting has been selected. brightness with the headlights on or off. Adjust the brightness with the “+”...
Page 705 MULTIMEDIA • Pressure Status setting press the “Show Time Status” button on the Select from: “psi,” “kPa,” or “bar.” touchscreen and select from “ON” or “OFF.” • Temperature • Sync Time — If Equipped Select from: “°C,” or “°F.” When in this display, you may sync the time with GPS. Clock &...
Page 706 704 MULTIMEDIA 8 mph (13 km/h), the transmission is shifted into PARK front of you. The forward collision button is located in or the ignition is switched to the OFF position. the Uconnect display in the controls settings. To turn the •...
Page 707 MULTIMEDIA are much closer to the vehicle in front of you. To change visual) to indicate the proximity to other objects. The the FCW+ status, press and release the “Near” “Med” or system can be enabled with Sound Only, or Sound and “Far”...
Page 708 706 MULTIMEDIA • LaneSense Warning — If Equipped this mode is selected, the Blind Spot Monitor (BSM) system is activated and will only show a visual alert in When this feature is selected, it sets the distance at which the outside mirrors. When Lights & Chime mode is the steering wheel will provide feedback for potential activated, the Blind Spot Monitor (BSM) will show a lane departures.
Page 709 MULTIMEDIA • Hill Start Assist — If Equipped • Tilt Side Mirrors In Reverse When this feature is selected, the Hill Start Assist (HSA) When this feature is selected, the exterior sideview system is active. Refer to “Electronic Brake Control mirrors will tilt downward when the ignition is in the System”...
Page 710 708 MULTIMEDIA setting, press the Headlights Off Delay button on the turned off if they were turned on by this feature. To make touchscreen, and choose either 0 sec, 30 sec, 60 sec or 90 your selection, press the “Lights w/Wipers” button on seconds.
Page 711 MULTIMEDIA • Daytime Running Lights • Auto Door Locks When this feature is selected, the headlights will turn on When this feature is selected, all doors will lock auto- while the engine is running. To make your selection, matically when the vehicle reaches a speed of 12 mph press the “Daytime Running Lights”...
Page 712 710 MULTIMEDIA NOTE: The seat will return to the memorized seat To make your selection, press the “Hands Free Lift Gate” location (if Recall Memory with Remote Key Unlock is set button on the touchscreen and select from “On” or “Off.” to ON) when the Remote Keyless Entry (RKE) Key Fob is •...
Page 713 MULTIMEDIA • Flash Lights With Lock activated. To make your selection, press the “Sound Horn With Remote Start” button on the touchscreen and select When this feature is selected, the exterior lights will flash “ON” or “OFF.” when the doors are locked or unlocked with the Remote •...
Page 714 712 MULTIMEDIA • Auto-On Driver Heated/Ventilated Seat & Steering Key Fob UNLOCK button twice to unlock the passen- ger’s doors. When “All” is selected, all of the doors will Wheel With Vehicle Start — If Equipped unlock on the first press of the RKE Key Fob UNLOCK When this feature is selected the driver’s heated seat and button.
Page 715 MULTIMEDIA DVD video system (if equipped), power sunroof (if Seat” button on the touchscreen until a check-mark equipped), and power outlets will remain active for up to appears next to setting, showing that setting has been 10 minutes after the ignition is cycled to OFF. Opening selected.
Page 716 714 MULTIMEDIA Once properly set, the compass will automatically com- “YES” button on the touchscreen and complete one or pensate for the differences when calibrated, and provide more 360-degree turns (in an area free from large metal or the most accurate compass headings. metallic objects).
Page 717 MULTIMEDIA • Surround Sound — If Equipped setting buttons on the touchscreen or by selecting any point on the scale between the “+” and “–” buttons on the This feature provides simulated surround sound mode. touchscreen. To make your selection, press the “Surround Sound” NOTE: Bass/Mid/Treble allow you to simply slide your button on the touchscreen, select “On”...
Page 718 716 MULTIMEDIA • Subscription Information Phone/Bluetooth After pressing the “Phone/Bluetooth” button on the New vehicle purchasers or lessees will receive a free touchscreen the following settings will be available: limited time subscription to SiriusXM Satellite Radio with your radio. Following the expiration of the free •...
Page 719 MULTIMEDIA Restore Settings Clear Personal Data After pressing the “Restore Settings” button on the After pressing the “Clear Personal Data Settings” button touchscreen the following settings will be available: on the touchscreen the following settings will be avail- able: • Restore Settings •...
Page 720: Customer Programmable Features - Uconnect
718 MULTIMEDIA Customer Programmable Features — Uconnect Press the “Apps ” button, then press the “Settings 8.4 Settings ” button on the touchscreen to display the menu setting screen. In this mode the Uconnect system allows you to access all of the available programmable features.
Page 721 MULTIMEDIA • Forward Collision Sensitivity screen. Pressing the Up or Down Arrow button on the right side of the screen will allow you to toggle up or The Forward Collision Warning (FCW) This means the down through the available settings. system will warn you of a possible collision with the KeySense vehicle in front of you.
Page 722 720 MULTIMEDIA • ParkSense — If Equipped • Rear ParkSense Volume The ParkSense system will scan for objects behind the The chime volume settings include LOW, MEDIUM, and vehicle when the transmission gear selector is in RE- HIGH. The KeySense default volume setting is ME- VERSE and the vehicle speed is less than 7 mph DIUM.
Page 723 MULTIMEDIA • Blind Spot Alert — If Equipped NOTE: If your vehicle has experienced any damage in the area where the sensor is located, even if the fascia is When this feature is selected, the Blind Spot Alert feature not damaged, the sensor may have become misaligned. Provides alerts, visual and/or audible, to indicate objects Take your vehicle to an authorized dealer to verify sensor in your blind spot.
Page 724 722 MULTIMEDIA • Subscription Information Display New vehicle purchasers or lessees will receive a free After pressing the “Display” button on the touchscreen limited time subscription to SiriusXM Satellite Radio the following settings will be available: with your radio. Following the expiration of the free •...
Page 725 MULTIMEDIA • Display Brightness With Headlights OFF nomenclature, including the trip functions and the navi- gation system (if equipped). Press the “Set Language” When in this display, you may select the brightness with button on the touchscreen, then press the desired lan- the headlights off.
Page 726 724 MULTIMEDIA • Speed Time-Out” button on the touchscreen until a check-mark appears next to the setting, showing that setting has been Select from: “MPH” or “km/h.” selected. • Distance • Navigation Turn-By-Turn In Cluster — If Equipped Select from: “mi” or “km.” When this feature is selected, the turn-by-turn directions •...
Page 727 MULTIMEDIA Voice Clock After pressing the “Voice” button on the touchscreen the After pressing the “Clock” button on the touchscreen the following settings will be available: following settings will be available: • Voice Response Length • Sync Time With GPS — If Equipped When in this display, you may change the Voice Re- This feature will allow you to automatically have the sponse Length settings.
Page 728 726 MULTIMEDIA • Set Time Minutes Safety & Driving Assistance After pressing the “Safety & Driving Assistance” button This feature will allow you to adjust the minutes. The on the touchscreen the following settings will be avail- “Sync time with GPS” button on the touchscreen must be able: unchecked.
Page 729 MULTIMEDIA • Forward Collision Warning — If Equipped ABA system becomes active at 5 mph (8 km/h). To make your selection, press the “Forward Collision Warning The Front Collision Warning (FCW) feature provides an Active Braking” button on the touchscreen, until a check- audible and/or visual warning to potential forward mark appears next to setting, indicating that the setting collisions.
Page 730 728 MULTIMEDIA • ParkSense — If Equipped indicating that the setting had been selected. ParkSense will retain its last known configuration state through The ParkSense system will scan for objects behind the ignition cycles. vehicle when the transmission gear selector is in RE- •...
Page 731 MULTIMEDIA • Tilt Side Mirrors In Reverse Spot Monitor (BSM) will show a visual alert in the exterior mirrors as well as an audible alert when the turn When this feature is selected, the exterior sideview signal is on. When “Off” is selected, the Blind Spot mirrors will tilt downward when the ignition is in the Monitor (BSM) system is deactivated.
Page 732 730 MULTIMEDIA display along with a caution note to “Check Entire “Controls” button on the touchscreen, the “settings” Surroundings” across the top of the screen. After five button on the touchscreen, then the “Safety & Driving seconds, this note will disappear. To make your selection, Assistance”...
Page 733 MULTIMEDIA • Sliding Door Alert remains less than 8 mph (12 km/h). When vehicle is shifted into a different gear (other than ‘REVERSE’), the When this feature is selected, a chime plays when the image will remain displayed for 10 seconds or until sliding door reverses or an obstacle is sensed.
Page 734 732 MULTIMEDIA • Hill Start Assist — If Equipped • Headlight Off Delay When this feature is selected, the Hill Start Assist (HSA) When this feature is selected, it allows adjustment of the system is active. To make your selection, press the “Hill amount of time the headlights remain on after the engine Start Assist”...
Page 735 MULTIMEDIA • Headlights With Wipers — If Equipped • Daytime Running Lights — If Equipped When this feature is selected, and the headlight switch is When this feature is selected, the headlights will turn on in the AUTO position, the headlights will turn on ap- whenever the engine is running.
Page 736 734 MULTIMEDIA • Flash Lights With Lock Doors & Locks After pressing the “Doors & Locks” button on the touch- When this feature is selected, the exterior lights will flash screen the following settings will be available: when the doors are locked or unlocked with the Remote Keyless Entry (RKE) Key Fob, or when using the passive •...
Page 737 MULTIMEDIA • Sound Horn With Remote Start NOTE: If the vehicle is programmed 1st Press Of Key Fob Unlocks “All Doors,” all doors will unlock no matter When this feature is selected, the horn will sound when which Passive Entry equipped door handle is grasped. If the remote start is activated.
Page 738 736 MULTIMEDIA • Power Liftgate Alert touchscreen, until a check-mark appears next to the setting, showing that the setting has been selected. When this feature is selected, an alert plays when the • Personal Settings Linked to Key Fob — If Equipped power liftgate is raising or lowering.
Page 739 MULTIMEDIA • Sliding Door Alert make your selection, press the “Hands Free Power Slid- ing Door” button on the touchscreen, until a check-mark When this feature is selected, a chime plays when the appears next to the setting, showing that the setting has sliding door reverses or an obstacle is sensed.
Page 740 738 MULTIMEDIA Engine Off Options button on the touchscreen to select your desired time interval, and choose from “0 seconds,” “45 seconds,” “5 After pressing the “Engine Off Options” button on the minutes” or “10 minutes.” touchscreen the following settings will be available: •...
Page 741 MULTIMEDIA • Equalizer • Surround Sound — If Equipped This feature allows you to adjust the Bass, Mid and Treble This feature provides simulated surround sound mode. settings. Adjust the settings with the “+” and “–” setting To make your selection, press the “Surround Sound” buttons on the touchscreen or by selecting any point on button on the touchscreen, select “On”...
Page 742 740 MULTIMEDIA • Channel Skip Phone/Bluetooth After pressing the “Phone/Bluetooth” button on the SiriusXM can be programmed to skip channels. To make touchscreen the following settings will be available: your selection, press the “Channel Skip” button on the touchscreen, select the channels you would like to skip. •...
Page 743 MULTIMEDIA NOTE: SiriusXM Travel Link is a separate subscription Clear Personal Data and is available for U.S. residents only. After pressing the “Clear Personal Data Settings” button on the touchscreen the following settings will be avail- able: Restore Settings • Clear Personal Data After pressing the “Restore Settings”...
Page 744: Steering Wheel Audio Controls
742 MULTIMEDIA System Information After pressing the “System Information” button on the touchscreen the following information will be available: • System Information When System Information is selected, a System Informa- tion screen will appear displaying the system software version. STEERING WHEEL AUDIO CONTROLS The remote sound system controls are located on the rear surface of the steering wheel at the three and nine o’clock Steering Wheel Audio Controls (Back View Of Steering...
Page 745: Radio Operation
MULTIMEDIA Pushing the center button will make the radio switch AUX/USB/MP3 CONTROL between the various modes available (AM/FM/SXM/ There are numerous USB ports located throughout the AUX, etc.). vehicle. This feature allows an external USB device to be plugged into the USB port. The left-hand control is a rocker-type switch with a push-button in the center.
Page 746 744 MULTIMEDIA • In the center console • On the back of the front row seats in the Uconnect Theater Media hubs • Above the rear cup holders in the third row of seats Front Center Stack AUX Jack And USB Ports 1 —...
Page 747: Uconnect Theater - If Equipped
MULTIMEDIA UCONNECT THEATER — IF EQUIPPED Your Uconnect Theater is designed to give your family years of enjoyment. There are multiple ways to interact with your Uconnect Theater system. • Play your favorite CDs, DVDs or Blu-ray Discs • Plug and play a variety of standard video games or devices into the HDMI port •...
Page 748: Getting Started
746 MULTIMEDIA Getting Started There are three different ways to operate the features of the Uconnect Theater: • The Remote Control • The Touchscreen Radio • The Individual Video Screens Uconnect Theater Screen 1 — Uconnect Theater Touchscreen 2 — Uconnect Radio 3 —...
Page 749: Accessing The System From The Uconnect Radio
MULTIMEDIA Accessing The System From The Uconnect Radio You can access your Uconnect Theater system from the radio touchscreen following the steps below: 1. Press the “Media” button. 2. Press the “Uconnect Theater” button icon. NOTE: The Uconnect Theater icon may be dragged and dropped down to the personalized menu bar to create an App/shortcut.
Page 750: Uconnect Theater Controls
748 MULTIMEDIA Uconnect Theater Controls Parents can control certain features of the system with the “Uconnect Theater Controls” screens, right from the Uconnect touchscreen radio. Options are: • Change media sources • Lock one or both screens • Mute an individual screen or both screens •...
Page 751: Accessing The System From The Uconnect Theater Rear Screens
MULTIMEDIA Accessing The System From The Uconnect Theater Rear Screens You can also access your Uconnect Theater system from the rear screens from the steps below: 1. Lift screen upward, the system will automatically power on. NOTE: A message asking if you would like to pair a remote will pop up if one has not already been paired to the system.
Page 752: Pairing The Remote
750 MULTIMEDIA NOTE: Pairing The Remote • There will be a touchscreen notification message when pairing is successful. Repeat the above steps to pair the second remote. • If remote is ever non-operational, try pairing remote. When watching a video source, pushing “Settings” icon on the touchscreen activates the Settings menu.
Page 753: Unpairing The Remote
MULTIMEDIA 2. Press the “Remote” button on the touchscreen in the will need to be unpaired from your Uconnect Theater settings menu. system. To unpair the remote, follow the procedure below: 3. Select “Pair Remote” and follow the on screen instruc- tions to complete the pairing process.
Page 754: Multimedia Media Sources
752 MULTIMEDIA Media Sources Users can select content for each screen from the radio by choosing desired content from drop down menu. NOTE: Use the “View Screen” function to pull content from one screen to the other in a single press of a button. Doing this however will disable and gray out certain player controls on the screen viewing the other screen’s content.
Page 755: Uconnect Theater Remote Control
MULTIMEDIA Uconnect Theater Remote Control 2. Mute Button — Mutes headphone audio. 3. Home Button — Push to access “Sources”. 4. Arrow Buttons — Push the arrow but- tons to highlight an item or scroll through menus. 5. Fast Forward Button —...
Page 756 754 MULTIMEDIA 9. Screen Selector Button — Push the screen selector to NOTE: Perchlorate Material — special handling may toggle between screen 1 (Driver Side), or screen 2 apply. Visit dtsc.ca.gov/hazardouswaste/perchlorate (Passenger Side). To replace the batteries: 10. Back Button — Push to exit out of menus or return to 1.
Page 757: Uconnect Theater Home Screen And Controls
MULTIMEDIA Uconnect Theater Home Screen And Controls Uconnect Theater Home Screen Source Card Selection 1 — Search Button (Media 5 — Source Card Page Indica- You can choose sources such as HDMI, USB, Apps, or Search) tor 1 or 2 Blu-ray.
Page 758: Play A Dvd/Blu-Ray Or Usb Media File From Uconnect Radio
756 MULTIMEDIA NOTE: NOTE: System information can also be displayed under General Settings. • Source card order can be changed by pressing the Remote Settings Settings button on the touchscreen and scrolling down to Source Card Order . Under this setting, you can access the following: •...
Page 759 MULTIMEDIA 2. Press the “Uconnect Theater” button on the touch- screen. Refer to “Accessing The System From The Uconnect Radio” in this section for further informa- tion. 3. Select Disc or USB from the source controls on the desired screen (1 or 2). NOTE: To play a DVD/Blu-ray disc on both screens simultaneously, select disc from both screen drop downs.
Page 760 758 MULTIMEDIA Using The Touchscreen Radio Source Controls — Uconnect Radio Media Control Screen NOTE: Control functions apply to individual screen selected displayed on touchscreen.
Page 761: Blu-Ray Controls - Disc Specific Functions
MULTIMEDIA 1. Power NOTE: Viewing a Blu-ray disc on the radio screen is not available in all states/provinces, and the vehicle must be Press to turn “selected Screen” On/Off. stopped, and the gear selector must be in the PARK 2. Mute position for vehicles with automatic transmission.
Page 762: Uconnect Theater Apps
760 MULTIMEDIA Uconnect Theater Apps Blu-ray Controls – Disc Specific Functions 1 — Red Button 3 — Blue Button Apps Home Screen 2 — Green Button 4 — Yellow Button...
Page 763 MULTIMEDIA • Hanging Fruit • License Plate Game • Math Flash Cards • Solitaire • Sudoku • Tic Tac Toe NOTE: To exit a game, push “Exit Button” than “Back Arrow,” or “Home Button” on the touchscreen. Home Screen Select the Apps source card to play pre-loaded games. Pressing the “Help”...
Page 764 762 MULTIMEDIA Are We There Yet? When a navigation route has been set from the Uconnect radio the second row passengers can use “Are We There Yet?” for an animated screen showing distance and time remaining on navigation routes as well as the estimated time of arrival with pop-up notifications.
Page 765: Using The Rear Video Usb Port
MULTIMEDIA Using The Rear Video USB Port NOTE: To view USB media on the rear theater screens, insert a USB jump drive into the port on the DVD/Blu- ray disc player. The USB jump drive port is located under the radio controls in the instrument panel. Rear Video USB Port Plug in a jump drive, iPhone, iPod or mass storage device and play your favorite music or movies.
Page 766: Play Video Games
764 MULTIMEDIA Play Video Games Connect the video game console to the HDMI 1 or 2 ports, located behind the first row seat. AUX/HDMI/USB 1 — AUX Jack (Headphone Output Only) 2 — HDMI Port 3 — USB Port (Charge Only)
Page 767: Headphones Operation
MULTIMEDIA CAUTION! Certain high-end video games will exceed the power limit of the vehicle’s Power Inverter. Refer to “Power Inverter” in “Getting To Know Your Vehicle” in this guide for further information. Headphones Operation The headphones receive two separate channels of audio using an infrared transmitter from the video screens.
Page 768 766 MULTIMEDIA NOTE: Uconnect Theater must be turned on before sound can be heard from the headphones. To conserve battery life, the headphones will automatically turn off approximately three minutes after the Uconnect Theater system is turned off. Changing the Audio Mode for Headphones 1.
Page 769 MULTIMEDIA To replace the batteries: How Long Does the Coverage Last? This warranty lasts as long as you own the Product. 1. Locate the battery compartment on the left ear cup of the headphones, and then slide the battery cover What Does This Warranty Cover? Except as specified downward.
Page 770: Disc Menu
768 MULTIMEDIA DAMAGES OF ANY KIND OR NATURE WHATSO- If you have any questions or comments regarding your EVER. Some states and jurisdictions may not allow the Delphi Automotive wireless headphones, please phone exclusion or limitation of incidental or consequential 1-888-293-3332.
Page 771: Listening To Audio With The Screen Closed
MULTIMEDIA Listening To Audio With The Screen Closed Rear Climate Controls To listen to only audio portion of the channel with the The rear climate controls can also be controlled using the screen closed: Uconnect Theater system. Refer to “Climate Controls” in “Getting To Know Your Vehicle”...
Page 772: General Information
770 MULTIMEDIA General Information Regulatory And Safety Information The operation is subject to the following two conditions: USA/CANADA Exposure to Radio Frequency Radiation 1. This device may not cause harmful interference. The radiated output power of the internal wireless radio 2.
Page 773 MULTIMEDIA situations or environments, such as aboard airplanes. If and, if not installed and used in accordance with the you are unsure of restrictions, you are encouraged to ask instructions, may cause harmful interference to radio for authorization before turning on the wireless radio. communications.
Page 774: Uconnect Voice Recognition Quick Tips
772 MULTIMEDIA UCONNECT VOICE RECOGNITION QUICK TIPS Introducing Uconnect Start using Uconnect Voice Recognition with these help- ful quick tips. It provides the key Voice Commands and tips you need to know to control your Uconnect 5.0, 8.4 or 8.4 NAV system. Uconnect 5.0...
Page 775: Get Started
MULTIMEDIA Get Started All you need to control your Uconnect system with your voice are the buttons on your steering wheel. 1. Visit UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing in- structions. 2. Reduce background noise. Wind and passenger con- versations are examples of noise that may impact recognition.
Page 776 774 MULTIMEDIA 3. Speak clearly at a normal pace and volume while facing straight ahead. The microphone is positioned on the rearview mirror and aimed at the driver. 4. Each time you give a Voice Command, you must first push either the VR or Phone button, wait until after the beep, then say your Voice Command.
Page 777: Basic Voice Commands
MULTIMEDIA Basic Voice Commands The basic Voice Commands below can be given at any point while using your Uconnect system. Push the VR button . After the beep, say • Cancel to stop a current voice session • Help to hear a list of suggested Voice Commands •...
Page 778: Radio
776 MULTIMEDIA Radio Use your voice to quickly get to the AM, FM or SiriusXM Satellite Radio stations you would like to hear. (Subscrip- tion or included SiriusXM Satellite Radio trial required.) Push the VR button . After the beep, say •...
Page 779 MULTIMEDIA Uconnect 5.0 Radio Uconnect 8.4 Radio...
Page 780: Media
778 MULTIMEDIA Media TIP: Press the “Browse” button on the touchscreen to see all of the music on your AUX or USB device. Your Voice Uconnect offers connections via USB, SD, Bluetooth and Command must match exactly how the artist, album, auxiliary ports (If Equipped).
Page 781: Phone
MULTIMEDIA Phone Making and answering hands-free phone calls is easy with Uconnect. When the Phonebook button is illumi- nated for the Uconnect 5.0 and 8.4/8.4 NAV radios, your system is ready. Visit UconnectPhone.com for mobile phone compatibility and pairing instructions. Push the Phone button .
Page 782 780 MULTIMEDIA TIP: When providing a Voice Command, push the Phone button and say “Call,” then pronounce the name exactly as it appears in your phone book. When a contact has multiple phone numbers, you can say “Call John Smith work.” Uconnect 8.4 Phone Uconnect 5.0 Phonebook...
Page 783: Voice Text Reply
MULTIMEDIA Voice Text Reply PRE-DEFINED VOICE TEXT REPLY RESPONSES Uconnect will announce incoming text messages. Push Yes. Stuck in traffic. See you later. the Phone button and say Listen. (Must have com- Start without I’ll be late. patible mobile phone paired to Uconnect system.) Okay.
Page 784 782 MULTIMEDIA Apple iPhone iOS 6 or later supports reading incoming text messages only. To enable this feature on your Apple iPhone, follow these 4 simple steps: iPhone Notification Settings 1 — Select “Settings” 2 — Select “Bluetooth” 3 — Select the (i) for the paired vehicle 4 —...
Page 785: Climate
MULTIMEDIA TIP: Voice Text Reply is not compatible with iPhone, but TIP: Voice Command for Climate may only be used to if your vehicle is equipped with Siri Eyes Free, you can adjust the interior temperature of your vehicle. Voice use your voice to send a text message.
Page 786: Navigation
. After the beep, say: • For the 8.4 Uconnect System, say: “Enter state.” • For the 8.4 NAV Uconnect System, say: “Find ad- dress 800 Chrysler Drive Auburn Hills, Michigan.” 2. Then follow the system prompts. Uconnect 8.4 Navigation...
Page 787: Uconnect Access
MULTIMEDIA Uconnect Access Alaska and Hawaii. Services can only be used where coverage is available; see coverage map for details. WARNING! 9-1-1 Call ALWAYS obey traffic laws and pay attention to the Security Alarm Notification road. Some Uconnect Access services, including 9-1-1 Remote Door Lock/Unlock and Assist, will NOT work without an operable 1X (voice/data) or 3G (data) network connection.
Page 788: Register
786 MULTIMEDIA Register 3. A helpful Uconnect Care Agent will register your vehicle and handle all of the details. To unlock the full potential of Uconnect Access in your vehicle, you first need to register with Uconnect Access. Signing up is easy! Simply follow the steps above. Or, press the “Apps ”...
Page 789 MULTIMEDIA 3. Press the app you’d like to connect to your vehicle. 4. Enter your login information for the selected app and press Link. 5. Next time you’re in your vehicle, enable Bluetooth, pair your phone and select the Via Mobile app you want to play from the Uconnect touchscreen to stream your personalized music.
Page 790: Voice Texting
788 MULTIMEDIA Voice Texting You must be registered with Uconnect Access and have a compatible MAP – enabled smartphone to use your voice 1. To send a message, push the Phone button . After to send a personalized text message. For details about the beep, say the following command: “Send mes- MAP, visit UconnectPhone.com.
Page 791 MULTIMEDIA TIP: • Voice Texting is not compatible with iPhone, but if your vehicle is equipped with Siri Eyes Free, you can use your voice to send a text message. • Messages are limited to 140 characters. • The Messaging button on the touchscreen must be illuminated to use the feature.
Page 792: Yelp
790 MULTIMEDIA Yelp TIP: Once you perform a search, you can reorganize the results by selecting either the Best Match, Rating or Once registered with Uconnect Access, you can use your Distance tab on the top of the touchscreen display. voice to search for the most popular places or things around you.
Page 793: Siriusxm Travel Link
MULTIMEDIA SiriusXM Travel Link Need to find a gas station, view local movie listings, check a sports score or the 5 - day weather forecast? SiriusXM Travel Link is a suite of services that brings a wealth of information right to your Uconnect 8.4 NAV system.
Page 794: Siri Eyes Free - If Equipped
792 MULTIMEDIA Siri Eyes Free — If Equipped Siri lets you use your voice to send text messages, select media, place phone calls and much more. Siri uses your natural language to understand what you mean and will respond back to confirm your requests. The system is designed to keep your eyes on the road and your hands on the wheel by letting Siri help you perform useful tasks.
Page 795 MULTIMEDIA on the road and hands on the wheel. For your conve- While in Do Not Disturb, Conference Call can be selected nience there is a counter display to keep track of your so you can still place a second call without being inter- missed calls and text messages while you were using Do rupted by incoming calls.
Page 796: General Information
794 MULTIMEDIA • The term IC before the certification/registration num- General Information ber only signifies that Industry Canada technical speci- This device complies with FCC rules Part 15 and Industry fications were met. Canada RSS-210. Operation is subject to the following two conditions: Additional Information 1.
Page 797: Cd/Dvd Disc Maintenance
MULTIMEDIA Uconnect System Support: 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. • U.S. residents call 1-877-855-8400 (24 hours a day 7 days a week) or visit DriveUconnect.com 3. Do not apply paper or tape to the disc; avoid scratch- ing the disc.
Page 799 CUSTOMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or Speech SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE ..... . .798 Impaired (TDD/TTY).
Page 800: Suggestions For Obtaining Service For Your Vehicle
798 CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 801: Fca Us Llc Customer Center
CUSTOMER ASSISTANCE 799 • Authorized dealer name facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized FCA US LLC Customer Center dealer service manager first.
Page 802: In Mexico Contact
1-800-380-CHRY. Puerto Rico And U.S. Virgin Islands Canadian residents with hearing difficulties that require Customer Service Chrysler International Services LLC assistance can use the special needs relay service offered P.O. Box 191857 by Bell Canada. For TTY teletypewriter users, dial 711...
Page 803 CUSTOMER ASSISTANCE 801 Warranty expires. The manufacturer stands behind only We appreciate that you have made a major investment the manufacturer’s service contracts. If you purchased a when you purchased the vehicle. An authorized dealer manufacturer’s service contract, you will receive Plan has also made a major investment in facilities, tools, and Provisions and an Owner Identification Card in the mail training to assure that you are absolutely delighted with...
Page 804: Warranty Information
802 CUSTOMER ASSISTANCE WARRANTY INFORMATION If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in See the Warranty Information Booklet, located on the a group of vehicles, it may order a recall and remedy DVD, for the terms and provisions of FCA US LLC campaign.
Page 805: In Canada
CUSTOMER ASSISTANCE 803 In Canada Service Manuals If you believe that your vehicle has a safety defect, you These comprehensive Service Manuals provide the infor- should contact the Customer Service Department imme- mation that students and professional technicians need in diately.
Page 806 804 CUSTOMER ASSISTANCE Owner’s Manuals Call toll free at: • 1-800-890-4038 (U.S.) These Owner’s Manuals have been prepared with the assistance of service and engineering specialists to ac- • 1-800-387-1143 (Canada) quaint you with specific FCA US LLC vehicles. Included are starting, operating, emergency and maintenance pro- cedures as well as specifications, capabilities and safety Visit us on the Worldwide Web at:...
Page 807 INDEX...
Page 808 806 INDEX Adaptive Cruise Control (ACC) (Cruise Control) . . .409 Transporting Pets ..... . .373 Adding Engine Coolant (Antifreeze) ... .632 Air Bag Light .
Page 809 INDEX 807 Antifreeze (Engine Coolant)....631, 686 Auxiliary Power Outlet .....194 Disposal .
Page 810 808 INDEX Master Cylinder ......636 Center High Mounted Stop Light ....546 Parking .
Page 811 INDEX 809 Using The Top Tether Anchorage ... .369 Coolant Level ......634 Clean Air Gasoline .
Page 812 810 INDEX Delay (Intermittent) Wipers ....121 Electrical Outlet, Auxiliary (Power Outlet) ..194 Diagnostic System, Onboard ....261 Electric Parking Brake .
Page 813 INDEX 811 Overheating ......600 Overheating ......600 Towing .
Page 814 812 INDEX Turn Signal .....254, 377, 542 Freeing A Stuck Vehicle .....603 Flash-To-Pass .
Page 815 INDEX 813 Gasoline, Clean Air ......678 Washers ......112 Gasoline, Reformulated .
Page 816 814 INDEX Interior Appearance Care ....670 Keys ........19 Interior Fuses .
Page 817 INDEX 815 Center Mounted Stop ....546 Seat Belt Reminder ..... .232 Cruise .
Page 818 816 INDEX Lug Nuts .......676 Outside ......106 Rearview .
Page 819 INDEX 817 Filter Disposal ......624 Parking Brake......389 Identification Logo .
Page 820 818 INDEX Radiator Cap (Coolant Pressure Cap) ...633 Remote Keyless Entry (RKE) Radio Frequency Arm The Alarm ......38 General Information .
Page 821 INDEX 819 Rotation, Tires ......663 Seat Belt Reminder ..... .304 Seat Belt Maintenance .
Page 822 820 INDEX Heated .......94 Snow Chains (Tire Chains) ....661 Memory .
Page 823 INDEX 821 Steering Tire And Loading Information Placard ..644 Tilt Column ......101 Tire Markings .
Page 824 822 INDEX Rotation ......663 Cooling System Tips .....520 Safety .
Page 825 INDEX 823 Turn Signals......254, 542 Untwisting Procedure, Seat Belt ....311 UCI Connector .
Page 826 824 INDEX Wheel And Wheel Trim .....668 Wheel And Wheel Trim Care ....668 Wind Buffeting .
Page 827 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.

Chrysler 2017 Pacifica Owner's Manual

Getting to Know Your Vehicle

Getting to Know Your Instrument Panel

Safety

Starting and Operating

In Case of Emergency

Maintaining and Caring for Your Vehicle

Quick Links

Chapters

Related Manuals for Chrysler 2017 Pacifica

Summary of Contents for Chrysler 2017 Pacifica