Jet JAT-100 Operations & Parts Manual

3/8” pneumatic impact wrench

Advertisement

 
3/8" Pneumatic Impact Wrench
#505100, JAT-100
Operation & Parts Manual
M-505100
Edition 2
06/2015
JET
427 New Sanford Road
LaVergne, TN 37086
Ph.: 800-274-6848
www.jettools.com
Copyright © 2015 JET

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the JAT-100 and is the answer not in the manual?

Questions and answers

Summary of Contents for Jet JAT-100

  • Page 1   3/8” Pneumatic Impact Wrench #505100, JAT-100 Operation & Parts Manual M-505100 Edition 2 06/2015 427 New Sanford Road LaVergne, TN 37086 Ph.: 800-274-6848 www.jettools.com Copyright © 2015 JET...
  • Page 2: Warranty And Service

    Accessories; Shop Tools; Warehouse & Dock products; Hand Tools; Air Tools NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries, Inc., or any of its successors in interest to the JET brand.
  • Page 3: Safety Warnings

    10. The air tool must be properly lubricated before operating. Do not use this tool for other than its intended use. If used for other purposes, JET disclaims 11. Never start a percussion type air tool (chipper, any real or implied warranty and holds itself breaker, buster, etc.) without securing the...
  • Page 4 22. Shut off air supply and discharge any residual 33. Do not lubricate the tool with combustible pressure from tool before removing hose, liquids, such as kerosene, diesel or jet fuel. making adjustments, changing accessories, 34. Do not dispose of this tool with normal or storing tool.
  • Page 5: About This Manual

    As with any tool operation, safety of operator and bystanders should be first priority. If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com.
  • Page 6: Tool Specifications

    Specifications were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations.
  • Page 7: Setup And Assembly

    Any missing parts or damage should be reported Lowest setting ‘0’ is recommended for ® immediately to your JET distributor. Do not use a smaller nuts and bolts. Setting ‘8’ provides damaged tool. Read this instruction manual highest amount of torque and speed.
  • Page 8: Maintenance

    Always oil the tool and disconnect Tool Pressure air hose before storage. JET Air Tools operate on 70-to-100 psi (pounds Air system requirements per square inch) air pressure measured at the tool when the tool is operating. Set tool to 90 psi Use proper air hose size (refer to tool unless indicated otherwise.
  • Page 9 Use a light oil containing rust inhibitors, such as replaceable air filter that can be easily cleaned. SAE #10. Many JET air tools have integral oil reservoirs, which should be kept filled when in-line Use safety shut-off valves so air flow can be oilers are not used.
  • Page 10 Troubleshooting JAT-100 Impact Wrench Any disassembly of the tool should be done by qualified service personnel. For problems not addressed below, contact JET technical service at 800-274-6846. Problem Possible cause Remedy Tool will not start. Air valve closed or obstructed.
  • Page 11: Replacement Parts

    Problem Possible cause Remedy Severe air leakage. Air valve obstructed or damaged. Clean or replace. (Note: Minimal escape of Housing loose or damaged. Tighten or replace as needed. air is often normal for air tools.) Replacement parts Service parts are listed on the following pages. To order parts or reach our service department, call 1-800- 274-6848 Monday through Friday, 8:00 a.m.
  • Page 12 #505100, JAT-100, 3/8-inch Impact Wrench – exploded view JAT-100 Butterfly Impact Wrench  ...
  • Page 13 #505100, JAT-100, 3/8-inch Impact Wrench – parts list Index Part No. Description Index Part No. Description JAT100-01 Motor housing SM-40126 O-Ring S36 SM-40102 Anvil 3/8in. SM-40128 Snap ring ISTW-12 SM-40103 Retaining ring SM-40129 Washer JAT100-04 Throttle lever SM-40130 O-Ring 8.8x1.7...
  • Page 14 This page intentionally left blank.                                             JAT-100 Butterfly Impact Wrench  ...
  • Page 15 This page intentionally left blank.                                              ...
  • Page 16                                       427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com JAT-100 Butterfly Impact Wrench  ...

This manual is also suitable for:

505100

Table of Contents