Jet J-A3816 Operating Instructions And Parts Manual
  1. Manuals
  2. Brands
  3. Jet Manuals
  4. Power Tool
  5. J-A3816
  6. Operating instructions and parts manual

Jet J-A3816 Operating Instructions And Parts Manual

15-inch vari-speed drill press
Hide thumbs Also See for J-A3816:
Table of Contents

Advertisement

Quick Links

This .pdf document is bookmarked
Operating Instructions and Parts Manual
15-inch Vari-Speed Drill Press
Models: J-A3816, J-A5816, J- A5818
Model J-A3816
Model J-A5816
For models with serial no. 11110696 and higher
WALTER MEIER (Manufacturing), Inc.
427 New Sanford Road
LaVergne, Tennessee 37086
Part No. M-354500
Ph.: 800-274-6848
Revision D 11/2013
www.jettools.com
Copyright © 2013 Walter Meier (Manufacturing), Inc.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the J-A3816 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Jet J-A3816

Summary of Contents for Jet J-A3816

  • Page 1 This .pdf document is bookmarked Operating Instructions and Parts Manual 15-inch Vari-Speed Drill Press Models: J-A3816, J-A5816, J- A5818 Model J-A3816 Model J-A5816 For models with serial no. 11110696 and higher WALTER MEIER (Manufacturing), Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Part No.

  • Page 2: Warranty And Service

    Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET, Wilton or Powermatic branded websites.

  • Page 3: Table Of Contents

      Exploded View — Head Model J-A3816 ......................21   Parts List – Base Floor Models J-A3816, J-A5816 and J-A5818 ..............22   Exploded View – Base Floor Models J-A3816, J-A5816 and J-A5818 ............. 23 The specifications in this manual are given as general information and are not binding.

  • Page 4: Warnings

    Warnings 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace warning labels if they become obscured or removed. 4.
  • Page 5 24. Check for damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function - check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation.

  • Page 6: Safety Instructions For Drill Presses

    Safety Instructions for Drill Presses 1. All work shall be secured using either clamps or 6. Always wear protective wear when a vise to the drill press table. It is unsafe to use operating, servicing or adjusting machinery. your hands to hold any workpiece being drilled. Eyewear shall be impact resistant, protective safety glasses with side shields complying with 2.

  • Page 7: Specifications

    LED speed display on the faceplate of the machine. JET's 15-inch vari-speed drill press provides a solid base for drilling and offers a wide range of spindle speeds. The large quill provides greater accuracy.

  • Page 8: Introduction

    JET 15-Inch Assembly Vari-Speed Drill Presses, Models J-A3816, J- A5816, and J-A5818. This manual also includes The Drill Press is shipped with the head in parts listings and illustrations of replaceable lowered position. Follow these instructions to parts.

  • Page 9: Cleaning

    4. Figure 4: Loosen (do not remove) the four screws in the worm gear housing. Figure 4 5. Figure 5: Place the rack against the column and slide it down as far as it will go into the slot in the table bracket. (Position the rack Figure 6 with the longer flat area toward the top and the short flat area toward the bottom.)

  • Page 10: Depth Stop

    The speed control handwheel is located on the 1. The head assembly must be locked to the left side of the drill head. An LED speed column so the thrust produced by drilling will indicator is provided on the face plate on the drill not force the head assembly up the column.

  • Page 11: Maintenance

    Indication of Extreme Speeds and Feeds 4. Remove belt. (With speed control setting at the highest speed, the belt should be loose A drill that splits up the web is evidence of too enough to remove.) much feed or insufficient tip clearance at the center as a result of improper grinding.

  • Page 12: Adjustments

    Adjustments Table Adjustment The table can be raised or lowered to accommodate the height of the component being drilled (refer to Figure 9). To raise or lower the table, loosen the lock handle. Then use the hand crank to move the table to the desired height.

  • Page 13: Electrical

    230-volt plug. Figure 12 Permanently Connected Tools Models J-A3816, J-A5816 and J-A5818 drill Figure 11 presses that are intended for permanent connection should be connected to a grounded metal permanent wiring system or to a system...

  • Page 14: Grounding Instructions

    Grounding Instructions Extension Cords Make sure your extension cord is in good This tool must be grounded condition. When using an extension cord, be while in use to protect the operator from sure to use one heavy enough to carry the electric shock.

  • Page 15: Troubleshooting

    Troubleshooting Problem Probable Cause Suggested Remedy Spindle does Circuit breaker tripped. Reset circuit breaker. not turn. Branch circuit breaker tripped or fuse Reset branch circuit breaker/replace fuse. blown. Open wire in switch circuit. Repair open circuit. Defective switch. Repair switch. Replace drive belt.

  • Page 16: Parts List - Head Models J-A5816 And J-A5818

    Parts List - Head Models J-A5816 and J-A5818 Item Part No. Description Size Qty. 1 ....5507580....Chuck (with Key) ................... 1 2A .... 5507495....Arbor ..............#2 MT x JT3 ....1 3A .... 5507496A ....Spindle ....................1 4 ....J-5053070 ....Quill Band....................1 5 ....
  • Page 17 Parts List - Head Models J-A5816 and J-A5818 Item Part No. Description Size Qty. 55 ..... 5041140....Vaiable Speed Pulley (Spindle) .............. 1 55A ..5513510....Hex Nut ....................1 55B ..5513511....SHCS ....................1 56 ..... 9100421....Bearing....................1 57 ..... 9058571....Spring Washer ..................1 58 .....

  • Page 18: Exploded View - Head Models J-A5816 And J-A5818

    Exploded View — Head Models J-A5816 and J-A5818...

  • Page 19: Parts List - Head Model J-A3816

    Parts List - Head Model J-A3816 Item Part No. Description Size Qty. 1 ....5507580....Chuck (with Key) ................... 1 2A .... 5507495....Arbor ..............#2 MT x JT3 ....1 3A .... 5507496A ....Spindle Assembly ................. 1 4 ....J-5053070 ....Quill Band....................1 5 ....
  • Page 20 Parts List - Head Model J-A3816 Item Part No. Description Size Qty. 64 ..... 9138011....Self Tapping Screw ..........#10 x 3/4 Type A ..4 69 ..... J-5518168 ....Pulley Cover (w/door & latch) ..............1 70 ..... J-5518169 ....Face Plate ..................... 1 75 .....

  • Page 21: Exploded View - Head Model J-A3816

    Exploded View — Head Model J-A3816...

  • Page 22: Parts List - Base Floor Models J-A3816, J-A5816 And J-A5818

    Parts List – Base Floor Models J-A3816, J-A5816 and J-A5818 Item Part No. Description Size Qty. 1 ....1000772 ....Locknut ....................1 2 ....5003751 ....Table Lock (Plain Side) ................. 1 3 ....J-5507508 ....Table ....................1 4 ....

  • Page 23: Exploded View - Base Floor Models J-A3816, J-A5816 And J-A5818

    Exploded View – Base Floor Models J-A3816, J-A5816 and J-A5818...
  • Page 24 Walter Meier (Manufacturing), Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com...

This manual is also suitable for:

J-a5816J- a5818J-a5818

Table of Contents