2Touch 2150 series Installation Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

2Touch 2150 series

Interactive Whiteboard

Installation Guide

Revised 30 November 2010

This Installation Guide is intended for technicians installing a 2Touch board onto a flat

wall. It does not include the information required to adjust the 2Touch board's optical

system for best performance. This is the subject of a separate document.

CAUTION: Utilities and procedures referred to in this manual change the configuration of

the whiteboard's on-board processor. If these utilities are used incorrectly, the

whiteboard will not perform as designed, and may not function at all.

Please ensure that any access to these utilities is only by personnel trained and authorised

by 2Touch distributors. Always ensure that a backup copy is taken of the existing on-

board configuration file before any changes are made.

Table of Contents

Summary of Contents for 2Touch 2150 series

Page 1 Please ensure that any access to these utilities is only by personnel trained and authorised by 2Touch distributors. Always ensure that a backup copy is taken of the existing on- board configuration file before any changes are made.
Page 2 Even if you have no specific feedback to offer, your contact will always be welcome if only to register your name as a user of 2Touch boards. We will then be able to keep you informed of new developments, of where to download various software utilities, and of news relating to uses of the boards.
Page 3: Table Of Contents
Installing the 2Touch Audio (2Touch model 014) ..........15 Installing the 2Touch Audio (2Touch model 015) ..........15 Installing the Calibration Switch ................16 Installing the Epson EB450 Projector with a 2Touch IWB ......17 Installing the 2Touch Modular Connection System (MCS-1, MCS-2).....18 Final checks: ......................20 Registering your 2Touch Interactive Whiteboard ..........21...
Page 4: On Delivery
On Delivery Handling your 2Touch Board Always keep your 2Touch board right way up. The cameras are located at the top corners of the board. Placing the board upside down may damage or affect the camera settings. Do not store your 2Touch board horizontally or even on a significant lean, for more than a few minutes.
Page 5: Accessories For Your 2Touch Board
Accessories for your 2Touch Board Accompanying your 2Touch board is a wall mount kit containing four aluminium angle brackets and fasteners to secure these to the wall. If you have purchased the board is part of a “ready to install” pack, then the...
Page 6: Installation
Where a customer elects to “self-install” a 2Touch board, or use a person who is not a 2Touch Certified Installer to install a board, we advise careful study of this manual. It is also strongly recommended that a 2Touch Certified Installer...
Page 7: Additional Software Utilities
(to drill out rivets) Additional Software Utilities An accredited 2Touch technician will use either USB_Settings or USBConfig software utilities to ensure satisfactory performance after installation. The process of using these tools to analyse and optimise the performance of the...
Page 8: Removing Your 2Touch Board From The Packaging
Guide. Installers wanting to become 2Touch Certified Installers are invited to apply by email to installers@twotouch.com. Removing your 2Touch Board from the packaging The carton packaging comprises of an outer two-piece wrap plus top and bottom trays.
Page 9: Height Of The Iwb
USB feed from the wall connection point C (below). Typically, this zone also includes provision for audio connections in the case of the 2Touch model 014 audio solution. C. A wall connection panel provides users with the facility to connect: a.
Page 10 2m USB extension cable will be required if the wall panel is positioned on the right hand side of the board). Note also that in the case of the 2Touch 015 audio solution being used, there is no provision of USB ports on the front of the speakers. Therefore the...
Page 11 • USB cabling from the IWB to the powered USB hub, and from the powered USB hub to the wall panel; • Calibration switch cabling from the IWB to the desired location of the calibration switch. Copyright 2Touch Technologies Limited 2007-2008. All rights reserved.
Page 12: Installing Your 2Touch Board On The Wall
On the 2150 model of 2Touch IWB, electronics are included only in the top (horizontal) rail, and not on the other three sides of the board. Copyright 2Touch Technologies Limited 2007-2008. All rights reserved.
Page 13: Configuring The 2Touch Board To Suit Multiple Platforms
(50mm). Otherwise, a GPO will need to be provided within 900mm of the hub. 3. USB connection to IWB: The USB flylead on the 2Touch IWB is 1.6m long with a type A plug, and emerges from a position 300mm from the top left corner of the IWB.
Page 14: Installing A Cat5 Extender With A 2Touch Iwb
5. USB type A cable from board into hub outlet (note additional USB extension needed if port is placed on right side of board) 6. If 2Touch model 014 speakers supplied, then a USB type A male to USB type B male cable will be required to connect from a hub outlet port, to the USB input port on the active speaker.
Page 15: Installing The 2Touch Audio (2Touch Model 014)
Installing the 2Touch Audio (2Touch model 015) The 2Touch Audio_015 speaker assembly is the standard assembly included with 2Touch packages. It consists of an active (powered) speaker incorporating a stereo amplifier, plus a passive speaker.
Page 16: Installing The Calibration Switch
780 above and adhere these to any flat surface. • Front panel of speaker on 2Touch Audio 014 model. In this case, drill 12mm mounting hole through the front facia of speaker in lower recess, and fit easily switch 716 through from rear.
Page 17: Installing The Epson Eb450 Projector With A 2Touch Iwb
Installing the Epson EB450 Projector with a 2Touch IWB 1. Position bottom of bracket 40cm above top edge of whiteboard. 2. If image is to be placed at one edge of board, then projector bracket centreline should be 950mm from that (outer) edge of board (see diagram below).
Page 18: Installing The 2Touch Modular Connection System (Mcs-1, Mcs-2)
The MCS is available from 2Touch in two pre-configured packs: • A single gang (MCS-1) providing for three snap-in modules.
Page 19 A large slide on one side of the connector box can be removed for easy side access by cables or ducting. Additional holes are available through press-outs in the plastic container both at rear and on sides. Copyright 2Touch Technologies Limited 2007-2008. All rights reserved.
Page 20: Final Checks
Calibration performs correctly; Performance is accurate, responsive and comprehensive. Using 2Touch Workbook, rapidly draw dense lines on screen to ensure that there are no “dead spots” and that responsiveness is good. Draw fast tight circles all over the surface in a continuous stream (not “touch- off”), to ensure that circles and curves are smooth and that there are...
Page 21: Registering Your 2Touch Interactive Whiteboard
• Screen capture of camera scope from USB Settings • Saved .v299 board configuration file after install. If your board is not being installed by a 2Touch Certified Installer, then as a minimum please register your 2Touch device by advising the following to support@twotouch.com:...
Page 22: Using The 2Touch Board
Using the 2Touch Board Switching On Connect the cables and switch on power to any USB peripherals prior to connecting the USB cable to the 2Touch board. Connect and power up the computer and projector. The computer then automatically detects the USB device and, after a short pause, displays a series of messages on screen.
Page 23: Using Your 2Touch Board As A Mouse
Multi touch gestures on the 2Touch Board: If using the 2Touch board on a computer with Windows 7, the board surface can be used with 2Touch gestures to perform the following basic functions in any compliant Windows environment:...
Page 24: Caring For And Cleaning Your 2Touch Interactive Whiteboard
Caring for and Cleaning your 2Touch Interactive Whiteboard Cleaning the Whiteboard surface: The 2Touch IWB uses a porcelain steel whiteboard surface. Porcelain on steel whiteboard surfaces deliver the best performance in terms of eraseability, ease of cleaning and resistance to scratches and stains.
Page 25: User Software
Wordwall Where a 2Touch interactive whiteboard is purchased by either a primary or a secondary school, one concurrent-user license of the innovative Wordwall teaching and collaboration software is available for every 2Touch board purchased.
Page 26: Support Contacts
2Touch interactive whiteboard. Please ensure therefore that you have the serial number of the affected 2Touch board to hand before you call. This will allow the technician taking your call to access that unit’s factory history and any records available, and will also enable the call to be logged and any actions arising to be assigned.