Resetting The Handset; Base Station Settings; Specifications - Siemens Gigaset A160 User Manual

Resetting the handset

You can reset any individual settings and changes
that you have made. Entries in the directory, the
calls list and the handset's registration on the base
station will be retained.
¢ ¢
MENU Settings
¢ ¢
Reset Handset
a
Cancel the reset with

Base station settings

The base station settings are carried out using a
registered handset.
For details on how to set the system PIN for the
base station, and for how to select the ringtone
volume and melody on devices with answering
machines, see Menu tree, page 12.
Restoring the base station to the factory
settings
When the settings are restored all handsets are de-
registered. The individual settings are reset. Only
the date and time are retained.
¢ ¢
MENU Settings
¢ ¢
OK
Base Reset
If you have forgotten your system PIN you can reset
the base station to the original code 0000:
Disconnect the power cord from the base station.
Hold down the registration/paging key
(page 1) on the base station while reconnecting
the power cable to the base station at the same
time. If your device has an answering machine you
will also hear a beep.
The base station has now been reset and the sys-
tem PIN 0000 set.
Operating the base station on the PABX
The following settings are only necessary when
your PABX requires them, see the PABX user guide.
Changing the dialling mode
¢ ¢
3 3 9 1 1
MENU
dialling mode flashes: 0 = Touch tone dialling
(DTMF); 1 = Dial pulsing (DP)
¢
.
OK
Setting the flashing time
¢ ¢
I I O 1 2
MENU
rent flashing time flashes
2 = 120 ms; 3 = 400 ms; 4 = 250 ms; 5 = 300 ms;
6 = 600 ms; 7 = 800 ms
¢ ¢
OK OK
Handset
OK
.
¢ ¢
OK OK
Base
÷
or
The number for the set
¢
Enter number
The number for the cur-
: 0 = 80 ms; 1 = 100 ms;
¢ ¢
Enter number
9
Changing pause after line seizure
You can set the length of the pause inserted
between pressing the talk key
phone number.
¢
I I O 1 O
MENU
pause length flashes: 1 = 1 sec.; 2 = 3 sec.; 3 = 7 sec.
¢
Enter number
Changing the pause after the recall key
¢
I I O 1 4
MENU
pause length flashes: 1 = 800 ms; 2 = 1600 ms;
3 = 3200 ms
Appendix
Entering special characters
Standard characters
1x
1
Space
Q
.
P
*
#
Abc-->
123

Specifications

Recommended battery pack
ù
(Valid at the time of going to press)
Nickel-metal-hydride (NiMH):
Handset A16: V30145-K1310-X383
Handset A26: V30145-K1310-X359, X402
The handset is supplied with the recommended
battery pack.
Base station power consumption
In standby mode: approx. 2W
During a call: approx. 3W
General specifications
DECT standard
GAP standard
Range
Base station power supply 230 V ~/50 Hz
Environmental conditions
in operation
.
OK
c
and sending the
¢
The number for the current
¢
.
OK
¢
The number for the current
¢ ¢
Enter number
2x 3x 4x
1 £ $
, ? !
/ ( )
# @
123-->
abc
is supported
is supported
up to 300 m outdoors,
up to 50 m in buildings
+5 °C to +45 °C;
20% to 75% humidity
.
OK
5x 6x
¥ ¤
0 +
< =
\ &