Using The Sync Function; Slip Beat Looping; Slip Loop Slice/Reverse - Pioneer XDJ-RX Operating Instructions Manual

! At the point 4 beats after hot cueing began, the slip hot cue mode is
automatically canceled and normal playback of the sound that was
playing in the background resumes.
4 Release your finger from the Performance button.
Normal playback of the sound that was playing in the background
resumes upon releasing your finger from the Performance button before
4 beats have elapsed from the starting position of the hot cue.

 Slip beat looping

1 Press the [SLIP] button.
The mode switches to the slip mode.
2 Switch to the Auto Beat Loop function by pressing
the [AUTO BEAT LOOP] button.
3 Keep the Performance button pressed.
The loop is set automatically and loop playback begins.
You can specify 1 beat, 2 beats, 4 beats, and 8 beats from the left end.
Normal playback continues in the background even during loop
playback.
The [SLIP] button flashes in beat with the sound playing in the
background.
! If the Performance button is pressed while keeping the [SHIFT] but-
ton pressed, you can specify the beats as 1/16 beats, 1/8 beats, 1/4
beats, 1/2 beats from the left edge.
4 Release your finger from the Performance button.
Normal playback of the sound that was playing in the background
resumes.
5 Press the [RELOOP/EXIT] button.
The last loop that was set is played and the slip loop mode is set.
 Slip Loop Slice
1 Press the [SLIP] button.
The mode switches to the slip mode.
2 Switch to Loop Slice function by pressing the
[LOOP SLICE/EXIT] button.
3 Press the Performance button corresponding to the
beats to want be set (1 beat, 2 beats, 4 beats, 8 beats).
From the playback position where the Performance button was pressed,
the loops corresponding to the number of beats set are automati-
cally set, after which loop playback starts. During loop playback, the
Performance button will flash.
! If the track's BPM cannot be detected, the BPM is set to 120.
! This operation is not necessary when switching over to loop slice
function during loop playback.
4 Keep the Performance button pressed.
This plays the specified section intervals repeatedly.
To change the length of section interval without changing the
length of the loop, press the [CUE/LOOP CALL c (LOOP 1/2X)] or
[CUE/LOOP CALL d (LOOP 2X)] buttons while the Performance button
is pressed.
! Loop Slice does not work for loops longer than 16 seconds.
5 Release your finger from the Performance button.
Directly migrates to Slip Loop.
6 Press the [LOOP SLICE/EXIT] button or the
[RELOOP/EXIT] button.
Looping is canceled, and normal playback of the sound that was playing
in the background resumes.
16
En
 Slip reverse
1 Press the [SLIP] button.
The mode switches to the slip mode.
2 Press the [DIRECTION, REV] button while the playback
is going on.
The [DIRECTION, REV] button lights and reverse playback starts.
Normal playback continues in the background even during reverse
playback.
The [SLIP] button flashes in beat with the sound playing in the
background.
! Slip reverse play is automatically canceled after 8 beats have elapsed
from the position at which the [DIRECTION, REV] button was
pressed. The playback returns to normal after reverting to the back-
ground and the [DIRECTION, REV] button turns off.
! If the [DIRECTION, REV] button is pressed before 8 beats have
elapsed, the slip reverse cancels, and the normal playback of the
sound that was playing in the background resumes.
 Canceling the slip mode
Press the [SLIP] button.
The slip mode is canceled.
! The slip mode is also canceled when a track is loaded.

Using the SYNC function

This function can be used to automatically synchronize the tempo (BPM)
and beat positions on the left and right decks based on the tracks' beat
grid information as analyzed with rekordbox.
! Music files must be analyzed with rekordbox beforehand in order to
use the SYNC function. For instructions on analyzing music files with
rekordbox, see the rekordbox user's manual.
! The following describes the procedure for synchronizing the
[DECK 2] track to the [DECK 1] track.
1 Play a track that has been analyzed with rekordbox
on [DECK 1].
The deck on which a track that has been analyzed with rekordbox is
played first is set as the MASTER for the SYNC function.
! The master can also be specified by pressing the [MASTER] button.
2 Play a track that has been analyzed with rekordbox
on [DECK 2].
3 Press the [SYNC] button for [DECK 2].
[DECK 2] is synchronized to the tempo (BPM) and beat positions of the
track playing on [DECK 1].
! When the [SYNC] button is pressed again, the SYNC function turns
off.
! Use the procedure below to restore the currently playing track's
tempo (BPM) to its original tempo after turning the SYNC function
off.
— Move the tempo slider to the position of the synchronized
[TEMPO] (BPM), and then set it back to the center position.
— Reload the same track.
! Depending on the track's beat information, the sound may not be
synchronized after the [SYNC] button is pressed. If this happens, the
sound can be re-synchronized by pressing the [SYNC] button to turn
the sync mode off then back on.