Error Messages - Pioneer XDJ-RX Operating Instructions Manual

Functions and operations
Problem
Can't crossfade.
Back cue function does not work.
Beat effect does not work.
Color effect does not work.
SYNC function does not work.
SYNC function does not work even
when files are analyzed.
Settings are not stored in the memory. Has the power been turned off directly after
USB devices
Problem
USB device is not recognized.
Time is required to read USB devices
(flash memory drives and hard discs).
Playback does not start when a track
is loaded from a USB device.
File cannot be played.
Music files cannot be played.
DJ software
Problem
DJ software on a computer cannot be
operated.
DJ software's sound is not properly
output.
Sound being played is interrupted
when using DJ software.

Error messages

When this unit cannot operate normally, an error code appears on the display. Check the table below and take the measures indicated. If an error code
not shown on the table below is displayed, or if the same error code is displayed again after taking the indicated action, contact your store of purchase
or a nearby Pioneer service station.
Error code Error type
E-8302
CANNOT PLAY TRACK
E-8304
UNSUPPORTED FILE FORMAT
E-8305
Check
Is the [CROSS FADER CURVE (THRU,
(crossfader curve selector) switch set to [THRU]?
Is a cue point set?
Is the [LEVEL/DEPTH] control set to the center
position?
Is the [TRIM] control set to the proper position?
Is the [SOUND COLOR FX
(NOISE, GATE/COMP, CRUSH, FILTER)] button
pressed?
Is the [COLOR] control set to the proper position?
Has the music file been analyzed?
Is the beat grid irregular?
Is the beat grid properly tapped?
Are the BPMs of the tracks in the two decks too
different?
Are you scratching?
changing the setting?
Check
Is the USB device properly connected?
Is the USB device connected via a USB hub?
Is the USB device supported by this unit?
Is the file format supported by this unit?
—
Is there a large number of folders or files recorded
on the USB device?
Are files other than music files stored on the USB
device?
Are the files playable?
Is the auto cue function activated?
Is the file copyright-protected (by DRM)?
Are the music files damaged?
Check
Is the USB cable properly connected?
Are the DJ software's output settings and this
unit's [MIXER MODE] setting properly set?
Is the driver software properly set?
Is the driver software's latency value suitable?
Description of error
Track data (files) on the storage device cannot
be read correctly.
Music files that cannot be played normally
are loaded.
Remedy
, )] Set the [CROSS FADER CURVE (THRU,
switch to a position other than [THRU]. (page 27 )
Set a cue point. (page 12 )
Turn the [LEVEL/DEPTH] control clockwise or counterclockwise. (page 25 )
Set the [TRIM] control to the proper position. (page 25 )
Press any of the [SOUND COLOR FX (NOISE, GATE/COMP, CRUSH, FILTER)]
buttons. (page 26 )
Set the [COLOR] control to the proper position. (page 26 )
Analyze the file. (page 16 )
Set the beat grid properly. (page 19 )
The SYNC function will not work properly if the BPM of the track on the deck for
which the [SYNC] button is pressed is outside the adjustable tempo range of the
track on the deck for which the [SYNC] button is not pressed.
The SYNC function is disabled while scratching.
After changing settings, wait at least 10 seconds before turning the power off.
Always turn off the power by pressing [u] switch.
Remedy
Connect the device securely (all the way in).
USB hubs cannot be used.
This unit supports such USB mass storage class USB devices as external hard
disks and portable flash memory devices.
Check that the file format of the connected USB device is supported on the unit.
(page 4 )
Turn the power off, wait 1 minute, then turn the power back on.
When there are many folders or files, some time may be required for loading.
When files other than music files are stored in folders, time is required to read
them as well. Do not store files or folders other than music files on the USB
device.
Check that the file format of the playing track is supported on the unit. (page 4 )
Press and hold the [TIME MODE(AUTO CUE)] button for one second or more,
and disable the auto cue function. (page 19 )
Copyright-protected files cannot be played.
Play music files that are not damaged.
Remedy
Connect the unit and the computer directly by using the USB cable. USB hub
cannot be used. (page 6 )
Check the DJ software's settings, then check this unit's settings on the
[UTILITY] screen and set the proper signal path. (page 31 )
Set the driver software properly.
Set the driver software's latency to a suitable value.
Set the DJ software's latency to a suitable value.
Cause and action
The track data (file) may be corrupt.
dCheck whether the track (file) can be played on another player,
etc., capable of playing the same formats as this unit.
Format is wrong.
dReplace with music files in the proper format.
, )] (crossfader curve selector)
En
33