Additional Information; Troubleshooting - Pioneer XDJ-RX Operating Instructions Manual

Additional information

Troubleshooting

! Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points
below and the [FAQ] for the [XDJ-RX] on the Pioneer DJ support site.
http://pioneerdj.com/support/
Sometimes the problem may lie in another component. Inspect the other components and electrical appliances being used. If the problem cannot
be rectified, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
! The unit may not operate properly due to static electricity or other external influences. If this happens, normal operation can be sometimes restored
by removing the power cord after turning the power off, and turning the power back on after inserting the power cord into the power outlet.
Power supply
Problem
The power is not turned on.
None of the indicators light.
Audio output
Problem
No sound or small sound.
Distorted sound.
No sound is produced, or sound is
distorted or noisy.
Microphone sound is not output or
volume is low.
Sound is distorted when an analog
player is connected to this unit's
[LINE/PHONO] terminals.
Or, lighting of the channel level
indicator does not change even when
the [TRIM] control is turned.
Display
Problem
The playing address display is not
displayed in the remaining time mode.
The category is not displayed.
Nothing is displayed.
32
En
Check
Is the power cord properly connected?
Is the [u] switch of the power on?
Check
Are the [DECK 1, PHONO1/LINE1] and [DECK 2,
PHONO2/LINE2] selector switches set to the
proper positions?
Are the [TRIM] control, channel faders, crossfader
and [MASTER LEVEL] control set to the proper
positions?
Is the [LINE, PHONO] selector switch on this
unit's rear panel properly set?
Is the [MASTER LEVEL] control set to the proper
position?
Is the [TRIM] control set to the proper position?
Is the [LINE, PHONO] selector switch on this
unit's rear panel properly set?
Is the sound level input to the [MIC] terminal set to
an appropriate level?
Is this unit placed near a TV?
Is the [MIC LEVEL] control set to the proper
position?
Is the switch on this unit or the microphone
turned off?
Have you connected an analog player with a built-
in phono equalizer?
Is an audio interface for computers connected
between the analog player and this unit?
Check
—
Is the rekordbox library information stored on the
USB device?
Is the USB device write-protected?
Is the auto standby function activated?
Remedy
Plug in the power cord to an AC outlet. (page 6 )
Turn the [u] switch of the power on. (page 27 )
Remedy
Switch the channel's input source using the [DECK 1, PHONO1/LINE1] and
[DECK 2, PHONO2/LINE2] selector switches. (page 27 )
Set the [TRIM] control, channel faders, crossfader and [MASTER LEVEL] control
to the proper positions. (page 27 )
Properly set the [LINE, PHONO] selector switch on this unit's rear panel accord-
ing to the connected device. (page 6 )
Adjust the [MASTER LEVEL] control so that the master level indicator's orange
indicator lights at the peak level. (page 27 )
Adjust the [TRIM] control so that the channel level indicator's orange indicator
lights at peak level. (page 27 )
Properly set the [LINE, PHONO] selector switch on this unit's rear panel accord-
ing to the connected device. (page 6 )
Set the [MIC LEVEL] control to the proper position. (page 24 )
Turn the TV's power off or install this unit and TV away from each other.
Set the [MIC LEVEL] control to the proper position. (page 24 )
Turn the switch on.
For analog players with built-in phono equalizers, use with the [LINE, PHONO]
selector switch on this unit's rear panel switched to [LINE]. (page 6 )
If the analog player with built-in phono equalizer has a [LINE, PHONO] selector
switch, switch it to [PHONO].
If the output of the audio interface for computers is line level, use with the [LINE,
PHONO] selector switch on this unit's rear panel switched to [LINE]. (page 6 )
If the analog player has a [LINE, PHONO] selector switch, switch it to [PHONO].
Remedy
When playing files recorded in VBR, it may happen that the set cannot detect the
length of the track immediately and that some time is required for the playing
address display to appear.
Use a device onto which the library information has been exported from
rekordbox.
Cancel the USB device's write-protection so that this unit can write on it.
This unit is shipped with the auto standby function turned on. If you do not want
to use the auto standby function, set [AUTO STANDBY] to [OFF]. (page 29 )