Download  Print this page

Connecting The Receiver; Operation; Basic Settings - JTS UF-10R/12 Instruction Manual

Uhf wideband receiver 624 – 694 mhz
Hide thumbs

Advertisement

Table of Contents

5 Connecting the Receiver

1) Insert the two supplied antennas (1) into the
antenna jacks ANT. 1 and ANT. 2 (13) and put
them in a vertical position.
Hint: To increase the range and the interference resist-
ance, use two antenna amplifiers UB-900 / 2 (incl.
antennas) available as accessories instead of the
antennas provided. The amplifiers are supplied with
power via the antenna jacks of the receiver (
ter 6.1).
2) To connect the subsequent unit, e. g. mixer or
amplifier, two audio outputs are available:
XLR chassis plug (11)
balanced output (phantom power resistant)
for connection to a microphone input or to a
line input (The output level can be switched
accordingly,
6.3 mm jack (12)
balanced output for connection to a line input
3) Connect the power supply unit provided to the
power supply jack (10) and to a mains socket
(230 V~ / 50 Hz).

6 Operation

1) Switch on the receiver with the button
display (5) shows various information (
ter 1, item 5).
2) Turn the knob PUSH / CONTROL (7) to adjust
the output level of the XLR jack (11) and the
6.3 mm jack (12). As soon as the knob is turned,
the display shows the value adjusted (-31 dB ...
0 dB) in large characters. To mute the sound,
turn the knob counterclockwise until the mes-
sage
Volume Mute
-31 dB.
When you stop turning the knob, the level
value indicated in large characters disappears
after a few seconds. The value adjusted is then
shown after the symbol
3) All further settings are made via a menu:
a) To call up the main menu (fig. 1), keep the
button SETUP (6) pressed for two seconds
until the menu appears.
b) Turn the knob PUSH / CONTROL to select
the desired menu item. Then press the knob
to call up the menu item.
14
chapter 6.1.)
appears after the value
.
c) Turn the knob to change the setting or, if a
submenu appears, select a submenu item
and press the knob to call it up.
d) Menu item
to switch between setting in steps of 1 MHz
and steps of 0.025 MHz. Menu item
Channel
tween setting of group and channel.
chap-
e) To save a setting, press the button SETUP.
To return to the previous setting, press the
button EXIT (8) twice.
f) To return to the main menu from a submenu,
press the button EXIT or, if available, select
the menu item
PUSH / CONTROL.
g) To exit the main menu, press the button
Exit
press the knob PUSH / CONTROL.
All setting options via the menu can be found in
the following chapters.
4) To switch off the unit, keep the button
for two seconds until the display shows
OFF
.
If the receiver is not in use for a longer
(9). The
period of time, disconnect the power supply unit
chap-
from the mains socket; even if the receiver is
switched off, the power supply unit will have a
low power consumption.

6.1 Basic settings

1) If the receiver has been connected to the fol-
lowing unit via the XLR connector (11), make a
rough adjustment of the output level via the
menu item
a) Keep the button SETUP (6) pressed for two
seconds until the main menu (fig. 1) ap -
pears.
b) Turn the knob PUSH / CONTROL (7) to se -
lect the menu item
press the knob to call up the menu item.
Frequency
: Press the knob
: Press the knob to switch be -
Return
and press the knob
or select the menu item EXIT and
Output Level
:
Output Level
Output Level
Line
Mic.
Group/
pressed
Power
. Then
Fig. 4

Advertisement

Table of Contents
loading

  Also See for JTS UF-10R/12

  Related Manuals for JTS UF-10R/12