ADJ WiFLY EXR QA5 IP User Instructions page 8

WiFly EXR QA5 IP
mode.
3. Press the SET UP button and "SPEED:XX" will be displayed. Use
the UP and DOWN buttons to adjust the speed of the color
fade.
Auto Run Mode:
In this mode the WiFly EXR QA5 IP will run a auto program.
1. Plug the fixture in and press the MODE button until "AUTO RUN
FAD+SNAP" is displayed.
2. Press the SET UP button and "SPEED:XX" will be displayed. Use
the UP and DOWN buttons to adjust the speed of the Auto Run.
Static Color Mode:
1. Plug the fixture in and press the MODE button until "CLR MACS
COLOR:XX" is displayed. "XX" represents a number between
00-64.
2. Use the UP and DOWN buttons to scroll through the 64 colors
and find you desired color. After you have found your desired
color you can activate strobing by pressing the SET UP button to
enter the strobe mode.
3. "STROB:XX" will be displayed, this is strobe mode. The strobing
can be adjusted between "00" (flash off) to "15" (fastest flash).
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs. This
function also allows you to use your fixtures as spot lights. The WiFly
EXR QA5 IP has 5 DMX modes: 4 Channel mode, 5 Channel mode,
6 Channel mode, 10 Channel mode, and a 11 Channel mode. See
pages 19-26 for each mode's DMX traits.
1. This function will allow you to control each individual fixture's
traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
"DMX MODE ADDR:XXX" is displayed. "XXX" represents the dis-
played DMX address. Use the UP or DOWN buttons to scroll
through and find your desired DMX address.
3. After you have set your DMX address press the SET UP button so
that "CHAN:XX" is displayed. "XX" represents the current DMX
Channel mode that is displayed. Use the UP or DOWN buttons to
ADJ Products, LLC - www.adj.com - WiFly EXR QA5 IP User Manual Page 14
Operating Instructions WiFly EXR QA5 IP
scroll through the DMX Channel modes.
4. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX con-
troller.
Battery Life:
This is used to check/display the battery life.
1. Plug the fixture in and press the MODE button until "BATT LEV
XXX" is displayed. "XXX" represents the remaining battery life. If
"BATT LEV ----" is displayed, it means either the battery is dead or
your running the unit on AC power.
Battery Load:
This is used to activate the PC board On.
1. Press the MODE button until "BATT LEV" is displayed.
2. Press the SET UP button until "BATT LEV LOAD:XX" is displayed.
"XX" represents either "ON" or "OFF".
3. Press the UP or DOWN button so that "ON" is displayed. If "ON"
is displayed already then the PCB is active.
Default Running Mode:
This is a default running mode. When this mode is activated all modes
will return to their default settings.
1. Plug the fixture in and press the MODE button until "OPTION
BLGT:XX" is displayed. "XX" represents either "on" or "oFF".
2. Press the SET UP button until "SYSRESET" is displayed.
3. Press the UP and DOWN buttons simultaneously to reset to
default settings.
ADJ RFC:
This function is used to activate and deactivate the ADJ RFC (Remote
Control). When this function is activated you can control the fixture
using the ADJ RFC. Please see the next page for ADJ RFC controls
and functions.
1. Plug the fixture in and press the MODE button until "OPTION" is
displayed.
2. Press the SET UP button until "RFXX" is displayed. "XX" repre-
sents either "ON" or "OFF".
3. Press the UP or DOWN buttons to either activate the remote func-
ADJ Products, LLC - www.adj.com - WiFly EXR QA5 IP User Manual Page 15
Operating Instructions